TOOLPORT L1-Q3 Universal Base Frame Instruction Manual
- June 16, 2024
- TOOLPORT
Table of Contents
PT-L1-Q36mx12m
Assembly instructions PE Tent
Safety Instructions
Introduction
Congratulations on the purchase of your new product and welcome to
TOOLPORT. Our customer service depart- ment or authorised sales representative
will be happy to answer your questions and give any valuable instructions.
Your new tent will give you freedom to plan many activities. It can be used at
a party, to screen you from the sun- light, as a shelter, for storage and in
many other ways.
Please observe the instructions provided below in order to extend the useful
life of your tent.
Important
Please read these assembly instructions before usage of the tent and keep
it for future reference.
Safety
The tent was not tested for wind and snow learly indicated by the
manufacturer. Therefore, these loads are not covered by guarantee. Please
watch the weather forecasts to be able to properly protect or disassemble the
tent before problems appear.
Warnings
Tents are intended for temporary accommodation and should be taken down in
adverse weather conditions. Always be sure to keep sufficient distance to
hoses as well as gas and power lines to avoid possible damage. Please check
the area for power cables and gas lines. Ask your local autority for further
information to avoid damages.
When using suitable heaters (available e. g. in specialist shops), keep a
minimum distance of 1.2 m to tarp material. Open fire or heaters with open
flames such as patio heaters, umbrella heaters, gas heaters etc. should not be
used in any case.
The person setting up the tent is responsible for adequately securing it to
ensure its safety. Please check the anchoring constantly to avoid damages. A
stabil anchoring can extend the endurance of the tent.
Please wear head protection, gloves and solid shoes. The heavy metal parts
could have sharp edges and could be oily because of rust prevention treatment.
Please make sure that there is no permanent snow load. It should be removed
right away. The same applies for rain and other forms of load.
Children should not play with the spare parts of the tent. These components
must be adequately protected. Please find a flat and even ground base to pitch
the tent. Only those materials provided with the tent can be used.
Caution!
Please check whether the ground base is suitable for your purpose. The tent
can be used also during temperatures a few degrees below zero. However, prior
to such use, the tarp material must be stored in temperature of at least 10 °C
for a sufficiently long time, and then unwrapped at such, or higher
temperature. Otherwise, the material may break at points of folds.
Each country has separate regulations regarding movable structures (tents) and
unmovable structures. Please ask your local authorities whether a permission
be obtained to pitch the tent. In some countries this depends on the size of
the tent. The tarps should not come into contact with any objects with sharp
edges.
Before first usage
Please unpack the cartons and check against the packing list enclosed whether
all parts have been delivered. Metal parts have been covered by a thin film of
lubricant in the manufacturer‘s plant. Some parts may have more than the
ordinary amount of lubricant on them. In such case, use a cloth to remove
excess lubricant. Please excuse us for that.
The screws joining the pipes with connectors must be tightened manually, using
a hexagon key or an automatic screw driver, set at a max. level 2, to avoid
material wear.
Cleaning and storage
Please do not use agressive chemicals to clean the tarp material. The best
cleaning agent is water with slightly alkaline reaction. The tent should not
be folded and packed when wet. First dry it thoroughly.
Do not make any modifications of the metal structure of the tent, such as for
example, connecting and/or welding additional loads, making grooves and/or any
deformations.
Please be careful when handling individual components of the tent. During
disassembly, please use the lopacking list again to check the possible missing
parts, so as to avoid problems with next assembly.
For outdoor use only. To be stored outdoors only.
Enviroment
After the end of usage, please do not dispose of the tent or any of its
components with ordinary garbage, but re- cycle it. If in doubt, please ask
the manufacturer or an authorised sales representative. We will be happy to
help you recycle the tent correctly, at the same time preserving the
environment.
Guarantee and customer services
For more information or replacement parts and accessoires, please write an
emailor contact us by telephone. Our customer service will be happy to help
you. For further questions please provide the article number.
The product was manufactured with utmost care and under constant control. If
you have any complaints, please contact the service hotline or contact us by
e-mail. Our service staff will coordinate with you as soon as possible. Please
keep the proof of purchase (receipt).
Contents
Item no. | 12 m | |
---|---|---|
33351 | 28 | |
33060 | ![TOOLPORT L1-Q3 Universal Base Frame - Contents |
2](https://manuals.plus/wp-content/uploads/2024/01/TOOLPORT-L1-Q3-Universal-
Base-Frame-Contents-2.jpg)| 18
33057| | 14
33079| | 14
33064| | 4
33065| | 10
33066| | 2
33067| | 5
33352| | 14
30430| | 100
30050| |
4
30080| | 12
30081| | 24
30051| | 4
| | 1
| | 2
| | 2
30046| | 4
30047| | 36
Assembly instructions
https://manuals.toolport.eu/CONTACT_FORM.pdf
Do you have any questions?
Contact us, we are happy to help!
TOOLPORT GmbH • Gutenbergring 1–5 • 22848 Norderstedt • GERMANY
Telefon +49 (0)40 / 60 87 27 17 • Fax +49 (0)40 / 60 87 27 37 •
www.toolport.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>