DEFA 715000 Power Premium Charging Station User Manual

DEFA 715000 Power Premium Charging Station

Description

DEFA Power is a premium charging station for electric vehicles and plug-in hybrids.
The charging station has been created with the user in mind. Smart features, simple set-up, and powerful functionality,
such as full dynamic load balancing and active phase rotation, characterizes the device. The charging station can be installed directly onto a wall or a pole, indoors or outdoors.

1. Precise load balancing: Utilizes all available power, independent of cloud connection.
2. Effective cooling: No derating ensures maximal charging power.
3. Active phase rotation: It utilizes power on all phases.
4. Intuitive display: Information and status sharing with the user.
5. Small and compact: It fits everywhere and can easily be installed and handled.
6. For everyone: It can handle all power and phase needs in European markets.
7. Plug and play: Easy installation, setup and configuration via app.
8. Powersmart: It minimizes charging cost by utilizing spot market energy prices and planning of charging curve.

A self-test of the built-in RDC-DD will be performed in every charging start- up cycle and every 24h.
If the built-in RDC-DD is tripped, a clear error message will be displayed on the screen.
To reset the built-in RDC-DD, unplug the charging cable from the vehicle and then plug it in again.

Safety information

Important! Read this document before using the device. Failure to follow any of the instructions or warnings can result in material damage or personal injury.
Important! If the device fails to behave according to instructions, immediately contact an electrician, responsible vendor or DEFA, see chapter Contact information.
Important! DEFA Power must be installed, uninstalled, or repaired by a licensed electrician. These actions must be executed in accordance with national and local regulations.

DANGER
Sections marked with this symbol draw attention to electrical voltages that represent a danger to life and limb. Actions contrary to these safety notices may lead to severe or fatal injury. Actions contrary to these safety notices must not be carried out under any circumstances.

WARNING
Sections marked with this symbol draw attention to additional hazards that may lead to damage to the cable itself or to other electrical devices. Actions marked with this symbol must be carried out with special care.

NOTICE
Sections marked with this symbol draw attention to additional important information and special features that are necessary for the reliable operation of the device. Actions marked with this symbol should be carried out as required.

Danger

Warning

Handling

DANGER Ensure that the cable is never run over by a vehicle.

Handle the cable with care and do not subject it to strong force or impact. Do not pull, twist, tangle, drag, or step on the cable or plug.

Always hold the cable by the plug when pulling it. Do not pull the cable itself.

Sorting
See chapter Store and protect for information about how to coil the cable correctly.

1. Always store the product with the cable coiled. Do not leave the cable on the ground after usage.
2. Attach the plug cap to protect the vehicle plug when the product is not in use.
3. Use the cable clip to coil the cable for when the product is not in use.

Main parts

A. Charging unit
B. Display
C. RFID-reader
D. Cable clip
E. Plug
F. Plug cap
G. Cable
H. Wall bracket
J. Locking tool
K. Rating label (public key)

Symbols on the display

Charging procedure

NOTICE Please read the charging instructions in the vehicle’s manual before using the charging station.
WARNING The plug locks to the vehicle inlet when charging starts. The plug stays locked until the charging procedure is finished. Always complete or end charging in the vehicle before unplugging (refer to the vehicle’s charging instructions for information about this).

Plug In

1. Pick up the plug, uncoil the cable, and remove the plug cap
2. Make sure that the charger is ready to be used. The Charger Ready icon should be visible on the display.
3. Insert the plug into the vehicle inlet. The following symbol should now be visible on the display to indicate that charging is initialized.
   • If authorization is enabled, that process has to finish before charging can begin. See the chapter Authorization for more information.
4. Make sure that charging has started. The following symbol should now be visible on the display.

NOTICE The plug must be fully inserted into the inlet of the vehicle. Failure to connect will prevent the vehicle inlet from locking the plug in place and start charging.

Unplug
WARNING Complete or stop the charging process before unplugging. To stop charging before the vehicle is fully charged, see the vehicle’s manual.

Unlock the plug from the vehicle, refer to the vehicle’s manual for more information.

1. Remove the plug from the vehicle inlet.
2. Put on the plug cap onto the plug.
3. Insert the cable into the clip.

Once the charger is disconnected, the display will show a summary of the charging session.

Authorization

If authorization is needed this icon will be shown on the display:

The authorization process can be completed by either:

1. Scanning your RFID-tag on the RFID-scanner, if the charger is registered to your account in the user application.
2. Opening the user application on your phone or scanning the QR code shown on the display. Follow the instructions shown on the screen.

If the authorization fails this icon will be shown on the display:

Check your user application or contact customer support of the facility.

Troubleshooting

The following symbols indicate that there has been an issue. In order to fix the issue, scan the QR-code on the screen and follow the instructions on the web page, or contact support.

Store and protect

Coil the cable
Roll the cable around the charging unit. Make sure that the plug hangs with the plug cap facing the ground. Attach the clip to the cable.

Use the plug cap
The plug strap can adjust the cap’s position. This prevents the cap from collecting water and dirt, and keeps the cap clear of the vehicle.

Maintenance and care

WARNING Do not flush water on the charging station. Do not use harsh chemicals when cleaning.

Checking

1. Keep the plug dry and check regularly for dust, dirt, pebbles, etc.
2. Check the cable regularly for cracks and other damage.

Cleaning
Use a damp cloth to clean. Do not use water or harsh chemicals.

Contact information

If you have any questions, contact your local vendor or visit defa.com
If you have any feedback on how the system or support can be improved, feel free to give us your input at defa.com

Technical specification

Item number| 715000|
---|---|---
Rated voltage| 380-420Vac (Three phase, 50-60Hz) 220-240Vac (Single phase, 50-60Hz)|
Charger type| Mode 3|
Connection to vehicle| Type 2|
RDC-DD| 6mA DC in acc. IEC 62955|
GRID type| TN/IT/TT|
Overheat protection| Internal sensor|
Operating temperature| -40°C to +50°C|
Storage temperature| -50°C to +85°C|
Size (L x W x T)| 113 x 167 x 350 mm|
Material control box| Plastic|
IK rating| IK 10|
IP rating| IP 55 (Wallbracket IP44)|
Weight| 5.0 kg|
Certification| CE, IEC61851, IEC62955|
Recycling| EE-waste|

We ‘DEFA AS’ hereby that this product (Product Name: DEFA Power™, Model Name: DEEVC/CT2/22 &DEEVC/WB480/22) is compliant with the essential requirements and other related provisions of Directive 2014/53/EU.
We have two labels, one of which is the unit label named DEFA Power Up and the other is the bracket label named DEFA Power Ready. The end product model name is combined with above two type names and Its name is DEFA Power™

To download a full manual in your local language and see user instructions or video/animations, scan the QR code or visit defa.com

References

• DEFA • World leading preheating, charging and inverter systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>