IMPECCA KJM-509B HD LED Home Thearter Projector User Guide

MPECCA KJM-509B HD LED Home Thearter Projector

IMPORTANT SAFETY INSTRUCTIONS

• CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
• WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
• CAUTION: TO PREVENT ELECTRIC SHOCK. DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
• WARNING: This equipment has been tested and found to comply with the limits for a Class B dig­ital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to correct the interfer­ence by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party responsible for compli­ance with the FCC Rules could void the user’s authority to operate this equipment.

FCC Declaration of Conformity Compliance Statement (Part 15):

• This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

The party responsible for compliance to these rules is: IMPECCAUSA

• Wilkes Barre, PA https://www.impecca.com.
• service@impecca.com.

CHILD SAFETY

• The projector should always be placed on proper, stable surfaces or installed according to the manufacturer’s recommendations.
• Don’t allow children to climb on or play with the projector and its surroundings. Route all cords and cables so that they cannot be pulled or grabbed by curious children.
• The warranty does not cover product failure due to improper installation. The unit and its acces­sories should not be adjusted or repaired by anyone except qualified service personnel.

Correct Disposal of this product

• This symbol on the product or in its packing indicates that this product may not be treated as household waste.
• Instead, it should be taken to the appropriate waste col­lection point for the recycling of electrical and electronic equipment.
• By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by the inappropriate waste handling of this product.
• For more detailed information about the recycling of this product, please contact your local council, your household waste disposal service, or the shop where you purchased the product.
• Please read and adhere to all safety instructions in this user guide. All governing codes and ordi­nances must be observed. If you are uncomfortable or unable to perform any of the steps in this guide, please consult a certified professional.

SAFETY PRECAUTION

SAFETY: CAUTIONS & WARNINGS

DANGER: ELECTRICAL SHOCK HAZARD

Touching the internal components of this device can cause serious personal injury or even death. Do not disassemble this unit.

• Do not tamper with or stare directly into the projector lens!
• Do not use an extension cord with this unit!
• Carefully review all of these instructions and warnings in the BEFORE operating your Projec­tor. Failure to do so may cause fires, damage, injury, or bodily harm.
• Do not use this product near water.
• Do not block any ventilation openings. Install following the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.
• Protect the power cord from being walked on or pinched.
• Use only with a cart, stand, bracket, or table allowed by the manufacturer. If a cart is used, use caution when moving it to avoid it tipping over and causing injury.
• Unplug this unit during lightning storms or when unused for a long period.
• Refer all servicing to qualified service personnel. Servicing is required when the unit or its or cord has been damaged in any way, such as the unit being dropped or exposed to water.
• NEVER expose this product to water, rain, or moisture. Objects filled with liquids, such as vases, should not be placed on or near the projector or its cables.
• Do not overload wall outlets, as this can result in fire or electric shock.
• Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short-out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
• This unit should only be serviced by qualified service technicians. Contact technical support for information regarding your closest authorized service center for further examination, re­pair, or adjustment to your unit.
• Do not immerse the cord or plug in water. Keep the cord away from hot surfaces. Do not let the cord hang over the edge of a table or stand. Do not operate this unit if the cord or plug is damaged or is not working correctly.
• When replacement parts are required, be sure the service technician uses replacement parts allowed by the manufacturer. Unauthorized substitutions may result in fire, electric shock, or other hazards.
• Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.
• When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet.
• Failure to do so may cause an electric shock and serious personal injury. Read the owner’s manual of the other equipment carefully and follow the instructions when making any connections.
• Sudden high-volume sound may cause hearing or speaker damage. When using headphones, keep the volume at a moderate level to avoid hearing damage.
• Do not allow the product to output loud, distorted sound for an extended period. It may cause speaker overheating and fire.

WHAT’S IN THE BOX

• Thanks for purchasing this 720p LED Home Theater Projector from mecca!
• This unit comes with a remote and supports HDMI, and AV inputs.
• It also accepts USB and SD Micro media and can connect to Bluetooth speakers!
• You should have received the following in the box along with this manual:

Projector Unit and Lens Cover

PRODUCT DAIGRAM

1. POWER Button
2. RETURN Button
3. NAVIGATION
4. MENU Button
5. SOURCE Button
6. Keystone Correction
7. Focusing Ring
8. LENS
9. Headphone Jack
10. AV
11. Micro SD Card
12. HDMI Port 1
13. HDMI Port2
14. USB Port
15. POWER INPUT
16. Adjusting Knob
17. POWER on Indicator
18. IR Window(Back Side)
19. IR Window(Front Side)
20. HDMI 3
21. Micro USB port(For power supply)

REMOTE CONTROL BUTTONS AND FEATURES

1. Power: Press to power ON. Press twice to power OFF. Mute: Press to mute volume.
2. VOL+ /VOL- (/): Press to adjust the audio level.
3. Arrows / OK: Press to navigate and confirm selections in Settings and other menus.
4. Return/ Exit: Press to exit the projector menu.
5. Flip: Press to flip the display image 180 degrees.
6. Home: Press to enter the home menu.
7. Menu: Press to access the projector Settings.
8. Play/Pause: Press to play or pause an individual chapter or track.

INSTALLING THE BATTERIES

INSTALLING THE BATTERIES FOR THE REMOTE

• To use the remote, you must first install the 2 AAA batteries (not included). Ensure they are inserted facing the correct direction, matching the + and – symbols in the battery compartment of the remote.
  • NOTE: Do not mix old and new batteries. Do not mix alkaline with standard (carbon-zinc) or rechargeable (ni-cad,ni-mh, etc.) batteries.

BUTTONS ON THE PROJECTOR

INSTALLING YOUR PROJECTOR

• The projector can be placed on a table or other similar, stable surface.
• It can also be mounted to the ceiling.
• Professional installation is recommended for a ceiling mount installation.
  • Warning: To avoid danger, please do not install the projector near water or extreme heat Do not block the ventilation on the back of the projector. 10 cm (4 inches) of free space must be available around the entire unit.

DETERMINING THE DISTANCE AND LOCATION OF THE PROJECTOR

• You may wish to measure the distance from the lens to the surface that the image will be projected on.
• This will give an idea of how big the projected image will be.

Light, brightness, etc. will affect the projection distance, this data is for reference only.
Projection Position
It is recommended to place the projector in front of the center of the screen.

IMPORTANT: For any type of installation other than front table projection, you will need to rotate the image. This can be done with the Flip button, or by noting the Rotate setting below and changing it in the Options section of the Settings menu (covered later in the guide).

PLACING THE PROJECTOR ON A TABLE

• Select a sate, stable surface and center the pro- jector lens on the surface it will be projecting on.
• Try to make sure that the projection surface is parallel with the front of the projector so that the projection is casting to the screen directly and is not angled to the left or right.
• The angle adjustment knob can later be used to raise or lower the angle of the projector.
• This will raise or lower the projected image.

MOUNTING THE PROJECTOR

MOUNTING THE PROJECTOR TO THE CEILING

• The projector does not ship with the neces- sary mounting hardware for ceiling mount installation. It does, however, have a built-in hanger hole to allow for this type of installa- tion.
• Professional installation is strongly recommended for mounting the projector to the ceiling. If you are not skilled and comfortable with mounting it to the ceiling, do not pertorm a ceiling installa- tion. Never perform any installation without assistance.

Ceiling Mount (Rear projection) (Rotate Setting: 1)

PLUGGING IN THE POWER AND SOURCE DEVICES

Before powering on the projector:

1. Attach the AC power adapter (included).
   • Note: Plug the power cable into the projector first and then into the power socket.
2. Attach any HDMI, or AV cables (not included) to the projector and also to their source (DVD player, computer, etc.).
3. Insert any USB drives or SD cards that will be used.
   • Note: If you change or remove any cables, USB cards or SD cards at a later time, be sure to power off the projector first, make the cabling adjustments and then power back on.

POWER ON AND ADJUSTING THE IMAGE

• When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount.
• Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt please ask the advise from an installation professional.
  • NOTE: Projector Mount and Screw(s) are not included.

ADJUSTING FOCUS

• As shown in the picture, adjust the lens focus wheel until you get a clear picture.

AV INPUT

• The “AV” input on the projector is for older RCA connections and requires a 3.5 mm AV cable, such as the following:

HDMI1 / HDMI2 / HDMI 3

• Simply connect your HDMI source to these inputs. HDMI cables carry both video and audio.

MEDIA PLAYER MODE (USB / SD CARDS)

• Your projector has both a USB port and an SD card slot for media playback.
• Each slot supports a card or drive of up to 32GB capacity.
• The projector supports viewing or playback of jpg, mp3, or mpeg video.
• Press SOURCE and select the Media Player. Se- lect USB or SD if necessary, then the media player interface will appear, allowing you to play back the content.
• Most of the play controls are self-explanatory, but here is an explanation of some of the extra features that you can select during playback:

Remember:

• Only 200 files per folder are supported. Please make sure pictures and other mediado not exceed this limit.
• When adding or removing USB or SD media, power off the projector first, change the media, then power back on.

THE MAIN MENU SYSTEM

• Press MENU to enter the main menu system. This is where you can view or change the projector’s settings.
• There are four primary sections in the menu.
• Use the 4-way directional button on the projector or remote to select the Menu section on the left. Press OK or to enter that menu.
• Let’s review some features in each of these menu sections.

PICTURE MENU

• This menu allows you to change the display to better match the projection surface.
• Picture Mode allows you to select pre-set styles it to Standard, Dynamic,
• Mild or you can set it to “User” to adjust this yourself.

Noise Reduction

• Smooths out the static/pixels and may be useful for some sources.

AUDIO MENU

• Sound mode can be selected here just as is it in the picture mode menu.
• You can select Music, Movie, User (custom), Sports, or Standard. If you find it necessary to frequently adjust the volume with the audio source you are using, Auto Volume may be useful for that as it will automatically regulate the sound level.

OPTIONS MENU

• This menu allows you to change the Language, active Bluetooth (covered later) or select
• Aspect Ratio. Projection mode is the setting used to rotate the image if the projector is used for anything other than front table projection.
• See the “Installing Your Projector” section for the correct setting, select Reset to restore the projector to factory settings. Info provides technical into on the projector.

Language Sub Menu

• Deutsch, English, Espanol, Francais, Polski, Italiano, Nederlands, Portuguese, Svenska, Suomi, Dansk, Norge, Hungarian, Czech, Slovakian, Croatian, Serbian, Chinese and Japanese

TIME MENU

• This menu allows you to set the system time or set a sleep timer to automatically power down (Press Power to exit sleep mode).
• You can also set an “on time” or “off time” for the unit to power on or off.
• This is only for a single instance and does not repeat on the next day.

USING EXTERNAL SPEAKERS AND HEADPHONES BLUETOOTH PLAYBACK

• The projector has its own speakers built-in but can also be paired with Bluetooth speakers.
• Bluetooth is disabled by default. Enable Bluetooth in the Options menu described in the previous section by selecting Bluetooth in the Options menu and turning it on.
• You will see a prompt to scan for Bluetooth devices.
• Enable Bluetooth on the receiver (external speakers, sound bar, etc.) to which you wish to connect.
• Devices such as smartphones, tablets, or computers are not Bluetooth receivers and will not connect to the projector.
• To eliminate confusion, you can disable Bluetooth on all receivers to which you do not wish to connect.
• Make sure the Bluetooth speaker is ready to pair with the projector and press OK on this screen to scan for speakers.
• Select the Bluetooth speaker on the projector screen and press OK. You will see a “Bluetooth connected” message once the pairing has been completed. The projector should remember this connection in the future.
• If the Bluetooth speaker you’ve paired is powered on and nearby with the projector is turned on again, the speaker should automatically be paired up.
• If not, return to the Options menu and pertorm the same steps again to pair with that Bluetooth speaker or another one.

AUDIO OUT

• The headphone jack (seen in the product diagram at the beginning of this guide) can be used with headphones.
• You can also connect speakers here, just as you would to connect computer speakers to a PC. This requires a 3.5 mm RCA audio cable.

CARE INSTRUCTIONS

PROTECTING THE LENS

• Always place the lens cover on the projector when it is not in use.

CLEANING

1. Turn off the Projector and unplug the power cable before cleaning.
2. Clean the Projector with 100% cotton cloth or micro-fibre cloth. Use a dry cloth if possible. If necessary, use a damp (but not wet) cloth and then a dry cloth afterwards. Do not use abrasive chemicals (such as alcohol, rosin, or toluene).
3. Use lens paper to clean the lens. Be careful not to scratch it.

CONDENSATION

• Moisture may form on the unit if it is moved from cool surroundings into a warm room or if the temperature of the room rises suddenly.
• When this happens, the unit’s performance may be impaired.
• To prevent this, let the unit stand in its new surroundings for about an hour before switching it on, or make sure that the room temperature rises gradually.

SPECIFICATIONS

Brightness Output White light output ANSI:| 200 Lu mens; LED light output: 8600 Lu mens; LED life: est. 50,000+ hours
---|---
Native Display Resolution| 1280 X 720
Supported HDMI Video Modes| 1080p, 1080i, 720p, 576i, 480p, and 480i
Power Consumption| Operating 72W; Standby lW
Power Input Rating| DC 30V, 2.4A
Power Adapter Specs| Input AC100-240V,50/60Hz; Output DC30V, 2.4A
Display Color| 6000-8000K
Projection Size| 30-150 inch
USB Drive and SD card support| Up to 32GB Capacity
Formats:| mpegl, mpeg2, mpeg4, mp3, jpeg
Weight| 1.35 KG
Dimensions| 221 X 68X

TROUBLESHOOTING TIPS

power light on? If it is not, check that the projector is plugged into a working outlet, and then press the power button on the projector.

•       If power is on, check that the lens cover has been removed.

•       Check that the cables are securely attached.

•      The image source may not be set correctly. Press the SOURCE button on the Control Panel or the Remote to select the correct setting.

The lamp (bulb) switches off after some time.| 1.      Leave the projector to cool for a few moments.

2.      Once cooled, check if anything is blocking the ventilation vents.

3.      Turn on the projector.

If the issue persists, please contact your support provider for further assistance.

The image is wider at the top/ bottom of the screen.| This is called the “keystone effect” and is due to the projection angle not being perpendicular to the screen. To correct this, use the keystone adjustment to correct the image.
Spots on the screen.| Use a portable vacuum cleaner to clean the lens. If cleaning doesn’t help, please contact your support provider for further assistance.
The image brightness has faded.| This could be caused by the ambient light in the room. Turn off lights or place curtains over any windows as needed. If the room is dark and the projection is still faint, you may need to have the lamp (bulb) replaced.

CUSTOMER SUPPORT

• Visit our website to contact us, find answers to Frequently Asked
• Questions, and for other resources which may include an updated version of this user’s manual.
  • www.impecca.com.

If you wish to contact us by phone, please be sure to have your model number and serial number ready and call us between 9:00 am and 6:00 pm ET, at + 1 866-954-4140. Keep tabs on Impecca’s newest innovations and enter contests via our social network feeds:

• www.facebook.com/Impecca/.
• www.instagram.com/impecca/.
• @impeccausa

LIMITED WARRANTY

IMPECCABLE 90 DAYS LIMITED WARRANTY

• Impecca® warrants this product against defects in material and workmanship to the original purchaser as specified below. Please register your product online within fourteen (14) days of purchase.
• If the product is determined to have a manufacturing defect, within ninety (90) days from the date of the original purchase, Impecca® will repair or replace the product parts at no charge (for parts) to consumers in the U.S.A.
• Shipping costs to and from our warranty service centre are the sole responsibility of the consumer.
• To obtain warranty service by an authorized Impecca® service center, please email us at: service@impecca.com to obtain a Repair and Maintenance Authorization (RMA) number and to locate the Warranty Service Center nearest you.
• Once authorized,  you must mail the product to the authorized Impecca® service center in its original product packaging materials or equivalent, to prevent damage while in transit. Further, should Impecca® determine that the product is outside of the Warranty terms, Impecca® will return the product to the sender at the sender’s expense without being repaired or replaced unless authorized by the consumer to service the out-of-warranty product at the consumer’s expense. All handling or restocking charges for returns and/or replacements shall be refundable.
• Impecca specifically excludes from this warranty any non-electric/mechanical attachments, accessories, and disposable parts including, but not limited to, outside case, connecting cables, batteries, and AC adapters. Impecca® reserves the right to repair or replace defective products with the equivalent, or newer models. same,
• We reserve the right to either repair or replace the product at our discretion.
• The replacement may be either new or refurbished and while every endeavour will be made to ensure it is the same model if the same model is not available, it will be replaced with a model of equal or higher specification.
• Normal “Wear and Tear” is not covered by this, or any other, warranty. Further, Impecca® hereby reserves the right to determine “Wear and Tear” on any products. Tampering or opening the product casing or shell will void this warranty in its entirety.
• In addition, this warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; has been altered or modified without the written permission of Impecca®; has been serviced by a non-authorized repair center of Impecca®; has not been properly maintained or operated according to the operation manual; has been used for commercial, non-household purposes; has been cosmetically damaged; was not imported by Impecca®; was not manufactured according to the specification of the United States market; was damaged due to improper installation by the or neglect consumer, was damaged due to improper packaging in shipment to the Warranty Service Center; was damaged due to natural disasters; or if the serial number for the product has been removed or defaced.
• ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE (1) YEAR PARTS AND NINETY (90) DAYS LABOR FROM THE DATE OF THE ORIGINAL RETAIL PURCHASE OF THIS PRODUCT.
• THESE WARRANTIES AND REMEDIES ARE THE SOLE AND EXCLUSIVE WARRANTIES AND REMEDIES IN CONNECTION WITH THE SALE AND USE OF THE PRODUCT. NO OTHER WARRANTIES, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, ARE GIVEN.
• IMPECCA® IS NOT RESPONSIBLE OR LIABLE FOR ANY DAMAGE, WHETHER SPECIAL, INCIDENTAL, CONSEQUENTIAL, DIRECT OR OTHERWISE, OR WHETHER KNOWN OR SHOULD HAVE BEEN KNOWN TO IMPECCA®, INCLUDING LOST PROFITS, GOODWILL, AND PROPERTY AND PERSONAL INJURY RESULTING FROM ANY BREACH OF WARRANTY, THE INABILITY TO USE THE PRODUCT OR UNDER ANY LEGAL THEORY IN CONTRACT OR TORT.
• IMPECCA LIABILITY IS LIMITED TO THE ACTUAL PURCHASE PRICE PAID TO THE RETAIL SELLER OF THE DEFECTIVE PRODUCT.
• No Impecca® dealer, agent, or employee is authorized to make any modification, extension, change or amendment to this warranty without written consent and authorization from Impecca®. Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages or do not allow a limitation on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state.

Important: Be Sure to Register Your Product at WWW.IMPECCA.COM within 14 Days Impecca®

• USA
• PA 18711
• www.impecca.com.
• service@impecca.com.

Do not send any returns to this address, as they may be lost and this will delay your repair and service process.

FCC

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.

Operation is subject to thefollowing two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

• MODEL: VP-302W
• www.impecca.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>