saxby lighting 91513 Lalo Round Fixed LED Downlight Instruction Manual
- June 4, 2024
- saxby lighting
Table of Contents
91513 Lalo Round Fixed LED Downlight
Instruction Manual
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This light fitting is double insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off the mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distances between the transformer each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position
cables and junction boxes (not supplied) away from areas where they may be at
risk of being cut, trapped, or damaged.
The distance between units must be 0.5m minimum.
The unit must be located a minimum distance of 100mm from a joist.
The main supply cable must have a minimum cross-section area of 1.0mm2.
Cables must be protected using suitable conduit or plastic trunking.
This product must be mounted out of arm’s reach.
This product is suitable for use in outside zones of a bathroom and Zone 2.
Please see the diagram.
If this unit is being fitted in a room containing a bath or shower, a 30mA RCD
must be used – in accordance with IEE regulations.
Installation
Existing fitting must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the switch is turned off before installation.
The ceiling surface must be flat and smooth to ensure a good fit.
After deciding on the layout of the light fittings ensure that the cables are
long enough to connect to desired positions.
Ensure a minimum ceiling void depth of 30mm is available.
Position the LED Driver next to the main outlet that the system will connect
to do not connect at this stage.
Cut a mounting hole of 35mm diameter in the ceiling taking care not to foul
any pipes, main cables, or joists beneath the surface.
It is always recommended to cut the hole slightly smaller than the size
specified, and then file the hole until the recessed unit fits snugly.
Pull the mains wire through the hole and connect it with the LED driver.
Press the spring leaf and fit it into the ceiling hole.
Push the unit up until firmly in position. Ensure that the product is fitted
properly in the hole.
Replace the fuse or circuit breaker and switch it on. Your light is now ready
for use.
Wiring
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect it to the connection block inside the LED driver in the following way:
Check that…
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
Technical data
Supply
Voltage:| 220-240 V~, 50 Hz
---|---
Bulb
Type:| 91513 / 99557: 4W LED module (SMD), 3000K
92518 / 99558: 4W LED module (SMD), 4000K
The light source of this luminaire is not replaceable; when the light source
reaches its end of life the whole luminaire shall be replaced.
| Conformity with all relevant UKCA Directive requirements.
| Conformity with all relevant EC Directive requirements.
| The power supply is Double Insulated and does not require connection to an
Earth circuit.
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
| This product can be dimmable when using dimmable driver 92519
| This product is rated at IP44.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
V3 01/11/2021
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>