Dimplex IgniteXL Built-in Linear Electric Fireplace User Guide

Dimplex IgniteXL Built-in Linear Electric Fireplace

Specifications

• Models : XLF50, XLF60, XLF74, XLF100
• Electrical Rating : Not specified
• UL Listing : Not specified
• Product Dimensions : Not specified

Product Usage Instructions

Welcome
Thank you for choosing to purchase a Dimplex fireplace. Please carefully read and save these instructions.

Important Instructions
Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard, and will void the warranty. Please record your model and serial numbers for future reference. Model and serial numbers can be found on the label located behind the front glass of your fireplace.

Installation
To install the electric fireplace, follow the steps below

1. Step 1 : Choose a suitable location for the fireplace.
2. Step 2 : Ensure that the power supply meets the electrical rating requirements.
3. Step 3 : Unpack the package contents.
4. Step 4 : Install the fireplace according to the provided wiring diagrams.
5. Step 5 : Connect the fireplace to the power supply.
6. Step 6 : Test the fireplace to ensure proper functionality.

Refer to the Troubleshooting section in case of any issues during installation.

Troubleshooting
If you encounter any problems with the electric fireplace, refer to the Troubleshooting section in the user manual. It provides solutions to common issues and helps you troubleshoot the fireplace.

Warranty
For warranty information, please refer to the Warranty section in the user manual. It contains details about the warranty coverage and how to contact Dimplex for assistance.

FAQ

• Q: Where can I find the model and serial numbers of my fireplace?
  A: The model and serial numbers can be found on the label located behind the front glass of your fireplace.

• Q: What should I do if I have questions or need support for this product?
  A: If you have questions regarding the operation of this product or if you require support, please visit the Dimplex website at www.dimplex.com for more information.

We value your feedback

Your input helps to create even better products and experiences.
Share the warmth and leave a review.dimplex.com/sharethewarmth

IMPORTANT SAFETY INFORMATION
Read this manual first before attempting to install or use this electric fireplace. Always comply with the warnings and safety instructions contained in this manual to prevent personal injury or property damage.
To view the full line of Dimplex products, visit www.dimplex.com

Conventions used in this manual

NOTE : Procedures and techniques that are considered important enough to emphasize.
CAUTION : Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
WARNING : Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death.

Welcome

Thank you and congratulations for choosing to purchase a Dimplex fireplace. Please carefully read and save these instructions.

WARNING : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.
Please record your model and serial numbers for future reference. Model and serial numbers can be found on the label located behind the front glass of your fireplace.

• Model
• Serial Number
• MOD

NO NEED TO RETURN TO THE STORE

If you have questions regarding the operation of this product or if you require service, before returning this product to the place of purchase,
Contact us a t: www.dimplex.com/support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-346-7539
Please have your model number and product serial number ready.

IMPORTANT INSTRUCTIONS

When using any electrical appliance, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons. These precautions include:

1. Read all instructions before using this electric fireplace.

2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the fireplace.
   DANGER : High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of the fireplace.

3. Extreme caution is necessary when the fireplace is used by or near children or people with disabilities and whenever the fireplace is left operating and unattended.

4. Young children should be supervised to ensure that they do not play with the appliance.

5. The appliance is not intended for use by young children or infirmed persons without supervision.

6. Do not operate the fireplace after it malfunctions, has been dropped, or damaged in any manner. Disconnect power at the service panel and have the fireplace inspected by a reputable electrician before using.

7. Do not use this fireplace outdoors.

8. Never locate the fireplace where it may fall into a bathtub or other water container.

9. To disconnect the heater, turn the unit off with the controls and turn off the power to the heater circuit at the main disconnect panel.

10. Do not locate the heater immediately below a fixed socket-outlet.

11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire, or damage to the fireplace.

12. To prevent a possible fire, do not block air intakes or exhaust in any manner.

13. All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.

14. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.

15. Do not burn wood or other materials in this electric fireplace.

16. Do not strike the fireplace glass.

17. Always use a qualified technician or service agency to repair this fireplace.

18. Disconnect all power coming to the fireplace at the main service panel before performing any cleaning or maintenance.

19. When transporting or storing the fireplace, keep it in a dry place, free from excessive vibration, and store to avoid damage.

SAVE THESE INSTRUCTIONS

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE

WARNING
Remote control contains small batteries. Keep away from children. If swallowed, seek medical attention immediately.
Do not install battery backwards, charge, put in fire or mix with used or other battery types – may explode or leak causing injury.

FCC CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

CALIFORNIA PROPOSITION 65 WARNING
This product can expose you to chemicals including nickel which is known to the State of California to cause cancer. For more information, visit www.P65Warnings.ca.gov

Technical Specifications

Electrical Rating

• Voltage : 120 V (3-Wire) or 240 V (4-Wire)
• Power : 1500 W at 120 V, 2500 W at 240 V

UL Listing
File Number : E71416

Model Reference

XLF50| 690963XXXX
XLF60| 691000XXXX
XLF74| 690969XXXX
XLF100| 690970XXXX

XXXX indicates a non-safety critical suffix.

Product Dimensions

Package Contents

Do not dispose of the suction cup after installation. Keep it in a secure location as it will be helpful for maintenance and service of the unit.

| Suction Cup| 0| 1| 1| 1
| 1 ½” Wood Screws| 4| 4| 4| 4
| Bubble Level| 1| 1| 1| 1
| Twist-on Wire Connectors|

4

|

4

|

4

|

4

| Wire Ties|

2

|

2

|

2

|

2

Package contents are subject to change

Installation

Placement

NOTE : It is recommended that the bottom of the unit be mounted between 5″ (13 cm) and 40″ (102 cm) from the ground to maintain an optimized viewing angle of the flame.
WARNING : The top of the fireplace must be installed a minimum of 24″ (61 cm) from the ceiling.
The fireplace must be installed a minimum of 5″ (13 cm) from the ground.

Installation in a Bathroom
If this unit is installed in a bathroom, it must be protected by a GFCI receptacle or circuit. If a receptacle is used, it must be readily accessible.
This electrical appliance is NOT watertight. To prevent electric shock, it must be installed as to prevent water from entering unit, or installed away from showers, tubs, etc. Never locate fireplace where it may fall into a bathtub or other water container.

Installation Recommendations for Overhanging Objects
For overhanging temperature-sensitive objects, such as a television, a mantel, or artwork, always follow the recommendations provided by its manufacturer for installation over a heater.
Figure 2 provides the overhang clearance recommendations for the fireplace. Areas above the fireplace are marked as follows

• Solid gray box ( ) is subject to temperatures greater than 65°C (149° F).
• Hatched box ( ) is subject to temperatures greater
• Clear box ( ) is subject to temperatures less than 40°C (104° F).

Installation Instructions
NOTE : Two people are required for installation.

1. Prepare a wall with a framed opening, following the dimensions shown in Figure 3. The fireplace can either be installed partially-recessed (2×4 frame) or flush-mounted (2×6 frame).
   CAUTION : Decorative finishing material (such as brick) should be limited to ½” (13 mm) overhang to ensure adequate flow of heated air out of the firebox area.
   CAUTION : This fireplace is NOT load-bearing. Ensure the opening for the fireplace is framed in such a way that the weight of the building materials will not create pressure on the top of the fireplace.
   ! NOTE : For 2″x4″ construction where the unit will be partially recessed, it is recommended to use XLFTRIM kit (sold separately) to accomodate the protruing portion of the fireplace. ! NOTE : Wiring entry is located on the right side at the bottom of the firebox. Plan the framing to allow routing of the power cable to this location.

2.  If a trimless installation is desired, remove the factory trim by removing the screws that secure it.

3.  Ensuring a minimum of 18″ (47 cm) of slack, route the supply power wire through a cable clamp (not included) and in the opening in the back of the unit. (Figure 4)

4. Lift the firebox into the opening in the frame using the handles on the back of the fireplace.

5. Using a bubble level (supplied) ensure that the fi replace is level within the framing. Adjust as required.

6. Drive four supplied mounting screws through the four mounting holes located on the inside surface of the fi replace chassis, into wall studs. (Figure 5)

7. Complete the wiring according to instructions in the Electrical Installation section (pages 12–13).

8. Complete the installation using the instructions in the following sections: Mirrored Glass Installation (page 15), Arranging Media (page 15), Front Glass Installation (page 16).

Electrical Installation

WARNING
The installation of the electric fireplace must comply with the applicable Local and/or National Electrical Codes and utility requirements.
Use the appropriate wire to meet local and national electrical codes for rated power consumption.
CAUTION : A dedicated, properly fused 15 Amp circuit is recommended, rated for the appropriate voltage (120 V, 240 V). A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

120 V Hardwire Installation

1. Cut the wire to an appropriate length.
2. Connect the black L1 wire from the unit to the live wire from the power supply with a wire connector.
3. Connect the white N wire from the unit to the neutral wire from the power supply with a wire connector.
4. Terminate the yellow L2 wire from the fireplace with a wire connector.
5. Connect the green G wire from the unit to the ground wire from the power supply with a wire connector or attach the grounding wire to the cover with the provided grounding screw, by placing the wire in between screw and lock washer and tighten.
6. Ensure all wire connections are tight and that wires are secured with wire ties and do not protrude past the flame panel, so as not to be visible after final installation.

120V Installation—Wall Switch
NOTE : Use a single pole, single throw (On/Off) wall switch that is rated for a minimum of 15 amps.

1. Cut the wire to an appropriate length.
2. Connect the black L1 wire from the unit to the live wire from the main power through the wall switch, ensuring all live connections are connected with a wire connector.
3. Connect the white N wire from the unit to the neutral wire from the power supply with a wire connector.
4. Terminate the yellow L2 wire from the fireplace with a wire connector.
5. Connect the green G wire from the unit to the ground wire from the power supply with a wire connector or attach the grounding wire to the cover with the provided grounding screw, by placing the wire in between screw and lock washer and tighten.
6. Ensure all wire connections are tight and that wires are secured a with wire ties and do not protrude past the flame panel, so as not to be visible after final installation.

240 V Hardwire Installation
You will need a 4-wire 240 V supply (L1, L2, Neutral, and Ground).

1. Connect the black L1 wire from the unit to the L1 wire from the power supply with a wire connector.
2. Connect the yellow L2 wire from the unit to the L2 wire from the power supply with a wire connector.
3. Connect the white N wire from the unit to the neutral wire from the power supply.
4. Connect the green G wire from the unit to the ground wire from the power supply with a wire connector or attach the grounding wire.
5. Ensure all wire connections are tight and that wires are secured with wire ties and do not protrude past  the flame panel, so as not to be visible after final installation.

Power Cord Installation
WARNING : Power cord option is only suitable for 120 V installations.

1. Remove the 3 screws that secure the pre-installed hardwire plate.
2. Connect the black L1 wire from the unit to the black wire of the plug kit.
3. Connect the white N wire from the fireplace to the white wire from the plug kit.
4. Terminate the yellow L2 wire from the fireplace with a wire connector.
5. Connect green G wire from the fireplace to the green wire from the plug kit.
6. Ensure all wire connections are tight and that wires are secured with wire ties and do not protrude past the flame panel, so as not to be visible after final installation.
7. Secure the power cord’s pre-installed cover plate using the screws removed when removing the hardwire plate. The previously removed electrical cover plate can be disposed of.
   WARNING : This heater is not intended for use with an extension cord. Plug the cord directly into an appropriate grounded receptacle.

Heater Hardware Disconnect
The fireplace heater can be permanently disabled by removing the electronic jumper on the main control board.
NOTE : Heater hardware disconnect will permanently disable the heater and fan. Follow these instructions only when an installation without heat is required. Temporary disabling of the heater can be achieved through the hidden touch controls. See “Heat Disable” in Operation section (page 18) for instructions.
To disconnect the heater and fan permanently

1. Locate the main control board. The heater hardware disconnect jumper location is labeled “HT EN”. (Figure 10)
2.  Pull out the heater hardware disconnect jumper.

Mirrored Glass Installation

1. Locate and remove the screws securing the mirrored glass bracket to the unit, along the top of the opening, and set bracket and screws aside. (Figure 11)

2. Remove the provided suction cup from the inside cavity of the unit (not found in XLF50 units).

3. Ensure that the back of the glass is clean and free from particles and fingerprints.

4. Secure the suction cup to the mirrored glass on the reflective side

5. Lift the mirrored glass and place it into the supports on the bottom at either side of the unit.

6. Tilt the mirrored glass into a vertical position.

7. Secure the mirrored glass bracket to hold the glass in place, using the previously removed screws.
   CAUTION : Ensure the mirrored glass does not fall forward while the mirrored glass mounting bracket is being installed.

8. Remove the suction cup and clean any fingerprints or debris off the glass with a non-abrasive glass cleaner.
   NOTE : Do not dispose of the suction cup! Keep it in a secure location, as it may be needed for maintenance and service on this fireplace.

Media Arrangement
For best results when using the supplied media, arrange as follows

1. Evenly space the large media in the media tray along the back of the media tray
2. Pour and evenly distribute the smaller crystals into the media tray.
3. If using the optional driftwood and river rock kit, evenly disperse the river rocks and place the driftwood pieces on top.

It is possible to use custom media ornaments to decorate your firebox. The custom media must fit easily without scratching the glass or bowing the media bed, and must not be composed of sand or liquid, which could interfere with the safety of the firebox.

Front Glass Installation

1. Ensure that the mirrored glass and the inside of the front glass is clean and free from particles and fingerprints.

2. Secure the suction cup (if provided) to the outside of the front glass.

3. Lift the front glass and carefully place the front glass into the lip located at the bottom of the opening of the fi rebox.

4. Tilt the glass into a vertical position.

5. Secure the front glass using the provided screws and hex key. (Figure 13)
   CAUTION : Ensure the front glass does not fall forward while the securing screws are being installed.

6. Install the provided screw covers by placing the tabs of the screw cover between sides of the front glass bracket.(Figure 14)
   NOTE : Do not dispose of the suction cup and hex key! Keep them in a secure location, as it may be needed for maintenance and service on this fireplace.

Operation

General Operation
WARNING : This electric firebox must be properly installed before it is used.
This firebox operates with Comfort$averTM technology, which automatically adjusts the fan speed and heater wattage to safely and precisely match the requirements of the room based on the thermostat setting. The heater operates such that once the room reaches the set point, the fan and heater will continuously run at a low level, to maintain the desired room temperature. If the temperature in the room rises significantly, the heater will turn off and periodically turn back on to circulate the air around the unit, until the room temperature drops and requires the heater to be
on again.

! NOTE : The element retains heat after shutdown. When the heat is turned off, there is a 2-minute cool down period before the fan shuts off completely.
! NOTE : The fireplace will retain the previously used settings after a power interruption.

Hidden Touch Controls
The hidden touch controls are located on the upper right of the fireplace. (Figure 15)
Remote Operation
The fireplace is supplied with a multifunction IR remote control. (Figure 16)
NOTE : To operate correctly, the remote control must be pointed toward the front of the unit.

Operation

Resetting the Temperature Cutoff Switch
Should the heater overheat, a manual limit cut-out will turn the unit off and it will not come back on without being reset. If the button on the unit is pressed, Er2 will be displayed on the unit. It can be reset by turning the unit off at the main disconnect panel and waiting 5 minutes before turning the unit back on.
CAUTION : If you need to continuously reset the heater, turn the unit off at the main disconnect panel and call technical support at: 1-888-346-7539.

Maintenance

Remote Control Battery Replacement
To replace the battery
Slide battery cover open on the remote control.
Correctly install one 3 Volt (CR2032 [longer life] or CR2025) battery in the battery holder with the + side facing up. Close the battery cover.

The battery must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area.
WARNING : Disconnect power and allow heater to cool before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons.

Cleaning
Mirrored Glass Cleaning
The mirrored glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the mirrored glass may collect dust particles; these can be removed by dusting lightly with a clean dry cloth.
To remove fingerprints or other marks, the mirrored glass can be cleaned with a damp cloth. The mirrored glass should be completely dried with a lint-free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners.
Fireplace Surface Cleaning
Use only a damp cloth to clean painted surfaces of the fireplace. Do not use abrasive cleaners.
The fireplace should not be operated with an accumulation of dust or dirt on or in the unit, as this can cause a build-up of heat and eventual damage. For this reason the heater must be inspected regularly, depending upon conditions and at a minimum yearly intervals.
Servicing
Except for installation and cleaning described in this manual, an authorized service representative should perform any other servicing.

Troubleshooting

For more troubleshooting, consult the XLF Service Manual which can be found at www.dimplex.com/product-downloads

Problem                      Display                        Cause Solution

Fireplace does not turn on with the manual touch controls| N/A| No incoming power| Ensure unit is wired correctly Check main disconnect panel Ensure wall switch is on (if applicable)
---|---|---|---
Fireplace does not turn on with the remote control| N/A| The batteries in the remote control are dead or installed incorrectly| Replace remote control battery Ensure battery is installed with + facing up.
Heater does not turn on| —| Heater is disabled| Press and hold  and  at the same time on the hidden touch controls for 3 seconds to disable or enable the heat function.
H–| Heater has been permanently disabled| If installation with heat is desired, reinstall jumper on main board if available or purchase new main board.
Er1| Thermistor problem| See service manual.
Er2| High temperature cut-out is activated| Ensure heater is free from obstructions. Reset breaker and wait 5 minutes before turning unit back on it. If error persists, see Service Manual.
Heater is on, but there is no heat| | Normal operation — There is a 30-second delay before heater starts| No action required.
Circuit breaker trips or fuse blows when unit is turned on| N/A| Improper circuit current rating| Install unit on a dedicated minimum 15 amp circuit.

Wiring Diagrams

Warranty

IGNITEXL® 5-YEAR LIMITED WARRANTY
Section 1 Products to which this Limited Warranty Applies
This Limited Warranty applies to your newly purchased Dimplex electric fireplace with model numbers
XLF50, XLF60, XLF74, and XLF100.
This Limited Warranty applies only to purchases made
in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska. This Limited Warranty applies to the original purchaser of the product only and is not transferable.

Section 2 Products excluded from this Limited Warranty
Products purchased in Yukon Territory, Nunavut, Northwest Territories, Hawaii, or Alaska are not covered by this Limited Warranty. Products purchased in these States, Provinces, or Territories are sold AS IS without Warranty or condition of any kind including, without limitation, any implied warranties or conditions of merchantability or tness for a particular purpose. The entire risk of as to the quality and performance of the products is with the purchaser. In the event of a defect, the purchaser assumes the entire cost of all necessary servicing or repair.

Section 3 What this Limited Warranty covers and for How Long
IgniteXL® products XLF50, XLF60, XLF74, and XLF100 excluding trims and accessory packages are covered by this Limited Warranty, have been tested and inspected prior to shipment and, subject to the provisions of this Warranty, Glen Dimplex Americas Ltd. (herein called Glen Dimplex Americas) warrants such products to be free from defects in material and workmanship for a period of 5 years from the date of the first purchase of such products. The 5-year Limited Warranty entitles the purchaser to On-site or In-home Warranty Services. Accordingly, Glen Dimplex Americas will be responsible for all labor and transportation associated with repairing or replacing
the product or part. Exceptions to this are outlined in Section 5. Some jurisdictions do not allow limitations on how long an implied Warranty lasts, so the above limitation may not apply to the purchaser.

Section 4 What this Limited Warranty Does Not Cover
This Limited Warranty does not apply to products that have been repaired (except by Glen Dimplex Americas
or its authorized service representatives) or otherwise altered. This Limited Warranty does further not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source.

Section 5 How to notify us of a Warranty Concern
Defects must be brought to the attention of Dimplex Customer Service online at dimplex.com/en/ contact_ us or by telephone at 1-888-346-7539. Please have proof of purchase, catalogue/model and serial numbers available for representatives to assist. **Limited In-home Warranty Services require proof of purchase.
In the event a product or part covered by this Limited Warranty is proven to be defective in material or workmanship during (i) the 5-year Limited Warranty period for products outlined in Section 1, you have the following rights

• Glen Dimplex Americas will in its sole discretion either repair or replace such defective product or part without charge. If Glen Dimplex Americas is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Glen Dimplex Americas may, in lieu of repair or replacement, choose to refund the purchase price for such product or part.

• Limited Warranty service will be performed solely by dealers or service agents of Glen Dimplex Americas authorized to provide Limited Warranty services.

• This 5-year Limited Warranty entitles the purchaser to On-site or In-home Warranty services. Accordingly, Glen Dimplex Americas will be responsible for all labor and transportation associated with repairing or replacing
  the product or part except as follows: (i) charges which may be levied for travel costs incurred to travel to the purchaser’s site where the product is located if the purchaser’s site is beyond 30 miles (48 km) from the closest service depot of Glen Dimplex Americas dealer or service agent; and (ii) the purchaser is solely responsible for providing clear access to all serviceable parts of the product.

• Glen Dimplex Americas will not be responsible for, and this Limited Warranty shall not include, any expense incurred for installation or removal of the surrounds
  (mantels) or trims or any part thereof (or any replacement product or part) including, without limitation, all shipping costs and transportation costs to and from the authorized dealer’s or service agent’s place of business and all labor costs. Such costs shall be the purchaser’s sole responsibility.

Section 6 When Glen Dimplex Americas and its Dealers and Service Agents are not Liable
IN NO EVENT WILL GLEN DIMPLEX AMERICAS, OR ITS DIRECTORS, OFFICERS, OR AGENTS, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY. WHETHER
IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF GLEN DIMPLEX AMERICAS OR ITS DIRECTORS, OFFICERS, OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE. IN NO EVENT
WILL GLEN DIMPLEX AMERICAS, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES, COSTS, OR DAMAGES THAT EXCEED
THE PURCHASE PRICE OF THE PRODUCT. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.

How State and Provincial law(s) apply
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this Limited Warranty or the sale of products covered by this Limited Warranty.

1-888-346-7539 | www.dimplex.com
In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice.
© 2023 Glen Dimplex Americas

A BRAND OF GLEN DIMPLEX AMERICAS

References

• Leave a review | Dimplex
• Electric Fireplace & Heating Solutions | Dimplex
• Product Downloads | Dimplex
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>