JYX K39 Wireless Lavalier Microphone User Manual

June 16, 2024
JYX

JYX K39 Wireless Lavalier Microphone

JYX K39 Wireless Lavalier Microphone

Product Introduction

Thank you for choosing our products.
This product is an intelligent wireless microphone, which can provide professional recording output. Plug and play, no app required. For multiple purposes: It can be used in live stream, video vlog shooting, program interview, interview recording, video teaching and other occasions.

The wireless lavalier microphone consists of two parts, the microphone transmitter and the receiver (as shown in the figure below)
Product Introduction

Outline Picture

Outline Picture

Transmitter Microphone:
Power: Press for 2seconds to turn on the transmitter, the connection light will blink. Double press to pause; Single press to switch between ‘Original’, ‘Noise Cancelling’ and ‘Echo’.
Volume+/-: Presse to increase/reduce volume (Connection light will blink once).
Power indicator: Red light blinks when battery low, and stays on when charging.
The light goes off when the power is sufficient or fully charged.
Connection indicator: White light blinks in search status and stays on when successful matching. The microphone will automatically turn off when ii has not been used torte minutes.
Pause: Quickly click the power button twice to pause, then the connection indicator will begin to blink; click twice again to cancel the pause, then the connection indicator will stay on.
Sound Effect: Click on the power button to switch between ‘Original’, ‘Noise Cancelling’ and ‘Echo’ mode. The light on the corresponding sound effect will light up.
Headset Output:3.5mm headset jack.
Charging Port/Monitor headset : USB-C charging port/Monitor headset jack.

Outline Picture

Receiver

Power : Press for 2seconds to turn on the receiver, the connection light will blink.
Volume+/-: Press to increase/reduce volume (Volume Indicator will change accordingly).
Power indicator : Red light blinks when battery low, and stays on when charging.
The light goes off when the power is sufficient or fully charged.
Connection indicator : While light blinks in search status and stays on when successful matching. The reviver will automatically turn off when it has not been used for ten minutes.
Headset Output : 3.5mm headset jack.
OTG! Charging Port : OTG/USB-C charging port

How To Connect To Your Device

  1. Press and hold the power button on the transmitter microphone (TX) and receiver (RX) respectively for 2 seconds to turn on the unit. The two units will be automatically paired.
    How To Connect To Your Device

  2. Connect the receiver to your device using the connection cable (Cell phone, tablet or camera).
    How To Connect To Your Device

  3. Click on the power button to switch to the desired sound effect.
    Then you can successfully start recording your voice or video.

  4. You can choose to connect a monitor headset to the transmitter microphone to listen to the sound you are recording.

Product Parameters

  • Transmission Distance ………………………………………………. 20M
  • Signal-to-noise Ratio ……………………………………………… ~90dB
  • Frequency Range ..  ………  …………..  …… Wireless Transmission
  • Frequency Response Range , ….  …………..  ………  .. 35Hz-20KHz
  • Charging time ………………………………………………………. 2 Hours
  • Working time ………………………………………………………. 12 hours
  • Charging Parameter ……………………………. USB-C DC 5V-500mA

Package Include

  • Transmitter Microphone …..  ……………………………………… 2 PCS
  • Receiver ……..  ………………………….  ………….. 1 PC
  • Lightning Adapter Cable ……………………………………………. 1 PC
  • USB-C Adapter Cable ……………………………………………… 1 PC
  • USB-C to USB-C Charging Cable …………………………………. 1 PC
  • User Manual …………………………………………………  ………. 1 PC

Symbols

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals