go-e IC-CPD Charger Gemini Flex User Guide

go-e IC-CPD Charger Gemini Flex User Guide

Important symbols

Warning of a hazardous situation with serious consequences if the safety regulations are not followed.
The task may only be carried out by a qualified electrician.
For more information, read the full installation and operating guide.

Note before installation/download

Observe all safety regulations (from page 22) and instructions in this quick reference guide! | Download the complete operating instructions and data sheet: www.go-e.com | Read all documents carefully and keep them for future reference.

Product overview

a RFID chip
b Reset card
c 16/32 A CEE red plug (Gemini flex 11/22 kW
d Housing
e RFID reader
f Button
g LED ring
h Type 2 socket
Back

i Rating plate
j Sealed screw

Installation

Required tools
a Pencil

b Spirit level

c Measuring tape

d Drilling machine

e Screwdriver

f Hammer

Enclosed mounting material
i Dowel 8 x 40 mm

j Screws for wall bracket 4.5 x 50 mm

k Screw for U-piece 4 x 50 mm

l U-piece (optional anti-theft device)

m Wall bracket

1. Place the wall bracket in the desired mounting position and align it straight. Mark the drill holes. The go-e Charger must be mounted just below the CEE socket so that little pressure is exerted on the supply line.

2. Drill holes at the four marked positions.

3. Attach the wall bracket with four screws and dowels each. Compensate possible unevenness of the wall with spacers.

4. Hook the g-e Charger into the wall bracket.
   Optional: attachment of the anti-theft device (U-piece).

5. Integrated DC protection module with DC detection and additional AC detection (6mA DC, 20mA AC). An RCD type A must be installed on the building side. In addition, a miniature circuit breaker must be connected upstream.

6. When installing multiple units, activate static load balancing via the go-e Charger app (WiFi required)

Commissioning/Charging

1. Connect the go-e Charger Gemini flex directly to a red CEE socket or to a suitable socket using an original go-e adapter.
   

2. The go-e Charger starts and performs a self-test.
   

3. The go-e Charger is ready for operation. Five predefined charging levels can be selected via the button (customizable via app).

4. Connect the go-e Charger and the vehicle via a type 2 charging cable. The Charger is ready for charging and is awaiting release by the car.
   

5. During the charging process, the LEDs rotate clockwise around the type 2 socket.

6. The charging process is completed when the LEDs light up green.

Cancel charging prematurely?
The cable remains locked after the charging process is complete (adjustable via app).

App

a For advanced features, you need the go-e Charger app.




b Set up connection via hotspot

1. Deactivate mobile data, terminate active WiFi connections
2. Scan the QR code of the reset card
3. Launch go-e Charger app
4. Select Charger and operate locally Alternative connection method?

c Set up connection via WiFi

1. Active hotspot connection required
2. Tap the „+“ icon in the app
3. Select „Initial setup for new go-e Charger“
4. Then follow the instructions of the app
5. Check under „Advanced settings“ (App tab „Internet“) whether connection to the go-e Cloud is allowed
6. Disconnect from the Charger‘s hotspot, connect your smartphone to the internet to control the Charger remotely via mobile data or WiFi.

References

• Smart Walboxes to Charge Your EV | go-e
• Smart Walboxes to Charge Your EV | go-e
• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>