E-Z-GO RXV-TITAN1000-2021 Titan 1000 Rear Seat Instructions

E-Z-GO RXV-TITAN1000-2021 Titan 1000 Rear Seat

ITEMS INCLUDED

•  Hardware Packs 1-8
•  Grab Bar
•  Armrests
•  Footrest
•  Main Frame
•  Main Brackets
•  Bagwell Brackets
• Main Bracket Support
• Bagwell Support Bracket
•  Drill
•  17mm Socket
•  17mm Wrench
•  14mm Socket
•  10mm Socket
•  #3 Phillips Bit
•  13mm Wrench

NOT REQUIRED when using cushions supplied with the seat kit
Use this bracket only when installing custom  cushions such as  TSUNAMI, or similar

WARNING:
We recommend professional installation. If you choose not to have this product installed by a professional, we highly recommend that you exercise caution, care, and patience when installing this product as it involves drilling holes into your cart’s body.

STEP 1
Remove factory canopy, rear struts, seat back and motor cover. Retain hardware.

STEP 2
Attach main brackets as shown on both sides using hardware retained from Step 1.

STEP 3
Attach factory struts to seat bracket as shown using hardware retained from Step 1.

STEP 4
Attach seat back to rear struts using hardware retained from Step 1.

STEP 5
Attach support bracket to main seat bracket as shown using hardware from Pack 1.

STEP 6
Attach main plyboard to support bracket using hardware from Pack 2.

STEP 7
Attach main poly board frame to bagwell bracket using hardware in Pack 2.

STEP 8
Install 01-076 adapter plates to main brackets and install rear seat backrest cushions.

STEP 9
Bolt rear seatback cushion to previously installed brackets and adjust to preferred height.

STEP 10
Use countersunk #3 Phillip bolt to attach bagwell bracket to support bracket and tighten using hardware from Pack 5. *Must be done before next step.

STEP 11
Attach bagwell bracket to cart and support bracket using hardware from Pack 5. For middle hole in support bracket use 8mm hardware, the 2” washer goes underneath the cart.

STEP 12
Attach armrest to poly seat frame as shown using hardware from Pack 6.

STEP 13
Attach footrest to bracket as shown using hardware from Pack 7.

STEP 14
Attach grab bar to footrest as shown using hardware from Pack 7.

STEP 15

Using quick release pins from hardware pack secure footrest to bagwell bracket as shown.

STEP 16
Attach seat bottom cushion as shown using hardware from Pack 8.

STEP 17
Reattach roof using hardware retained from Step 1.

STEP 18
Footplate can be folded up by removing the four c-clips and folding forward. To lock footplate in upright position use brackets as shown.

HARDWARE PACK

Pack 1

•  2 – 10x50mm hex bolt
•  4 – 10x20mm flat washer
•  2 – 10mm lock nut
•  4 – Rubber Washers

Pack 2

•  2 – 8x60mm hex bolt
•  4 – 8x15mm flat washer
•  2 – 8mm lock nut
•  6 – Rubber Washers
•  2 – 10x50mm Hex bolt
•  4 – 10x20mm flat washer
•  2 – 10mm locknut

Pack 3

•  4 – 8x50mm countersunk #3 Phillips
•  4 – 8x15mm flat washer
•  4 – 8mm locknut

Pack 4

•  4 – 6x25mm hex bolt
•  4 – 6x15mm flat washer
•  4 – 6mm lock washer

Pack 5

•  2 – 6x50mm hex bolt
•  4 – 6x15mm flat washer
•  2 – 6mm locknut
•  8 – Rubber Washers
•  1 – 10x85mm Hex bolt
•  2 – 10x20mm flat washers
•  1 – 10mm lock nut
•  1 – 2”x2” square washer
•  2 – 8x25mm countersunk #3 Phillips
•  2 – 8x20mm flat washers
•  2 – 8mm locknut

Pack 6

•  4 – 8x30mm hex bolt
•  4– 8x15mm flat washer

Pack 7

•  4 – 10x75mm hex bolt
•  8 – 10x20mm flat washer
•  4 – 10mm Locknut
•  4 – Quick release pins (easy remove hardware for folding in the foot plate)
•  8 – Rubber Washers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>