CANOPIA 82816 Aluminium Carport Verona 5000 Instruction Manual

June 13, 2024
CANOPIA

CANOPIA 82816 Aluminium Carport Verona 5000 Instruction Manual

Cover Page

SERVICE HOTLINE
TEL.: +49 (0) 6571 / 95117-0
FAX: +49 (0) 6571 / 95117-98

E-MAIL: INFO@50NRTH.COM

50NRTH GmbH
STRASSBURGSTR. 14-16
54516 WITTLICH / GERMANY
www.50NRTH.com

AFTER SALES SERVICE

WE´VE GOT YOU COVERED

Our self-service form makes it convenient and fast. Go to the URL below or scan the QR code with your phone to submit you request.

Missing a part or need a new one?

Need help assembling your product?

CUSTOMER SUPPORT

Customer Support

Customer Support Continued

SITE PREPARATION & FOUNDATION

A- PREPARE THE SITE

Prepare the Site

B- CHOOSE YOUR FOUNDATION TYPE

Choose Foundation Type

C- DIMENSIONS

Dimensions

SAFETY ADVICE

  • It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
  • Always wear work gloves during panel sliding.
  • Always wear shoes and safety goggles when working with extruded aluminium.
  • If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
  • Do not touch overhead power cables with the aluminium profiles.
  • Do not climb or stand on the roof.
  • Keep children away from the assembly area.
  • Do not attempt to assemble the product in windy or wet conditions.
  • Dispose of all plastic bags. Keep them out of reach of small children.
  • Do not lean against or push the products during construction.
  • Do not position your product in an area exposed to excessive winds.
  • Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
  • Make sure there are no hidden pipes or cables in the ground before anchoring to foundation.
  • This product is designed to be used mainly as a carport.
  • Heavy snow load on the roof can make it unsafe to stand below or nearby.
  • This product is specifically designed with a minor slope of the roof in order to allow drainage of water flow. Keep roof and gutters clear of snow, dirt & leaves.
  • Make sure to anchor the product directly to a solid foundation to increase the product’s stability and wind resistance, especially in areas with severe weather conditions.

CARE & MAINTENANCE

  • When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water.
  • DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
  • Clean the product once assembly is complete.

TOOLS & EQUIPMENT

Tools and Equipment

BEFORE ASSEMBLY

  1. Selecting a site:

    • Choose your site carefully before beginning assembly.
    • Choose a sunny position away from overhanging trees.
    • The product must be positioned and fixed on a flat level surface.
  2. The product must be secured directly to a solid foundation.

  3. This is a multi-part assembly best achieved by two people.
    Allow at least half a day for the assembly process.

  4. Take all components & parts out of the packages.
    Sort the parts and check against the content parts list.

  5. Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.

  6. Please note multi-sided profiles are used in this product.
    As a result some holes in the profiles are not used during assembly.

  7. Please review entire instructions before starting.
    Carry out the assembly steps in exact order.

  8. Please consult your local authorities if any permits are required prior to constructing the product.

  9. Use only the parts registered in the content list, some parts may be surplus.

IMPORTANT!

  • Firmly connect the product to a level surface immediately after completion of the assembly

  • Anchoring this product to the ground is essential to its stability and rigidity.
    It is required to complete this stage in order for vour warranty to be valid.

  • During assembly use a soft surface below the parts to avoid scratches and damages.

DURING ASSEMBLY

  • During assembly, you will encounter different icons for different products.
    Please see below for more information:

  • During assembly you will encounter the information icon, please refer to the relevant assembly step for additional comments and assistance.

  • You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.

  • Use a rubber mallet if necessary.

  • Peel the film covering the panel.

  • All panels with the stamped words “THIS SIDE OUT” must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place.

  • Steps marked with dashed outlines refer to Extensions only.

  • Some of the steps are irrelevant for an assembly of a single product

  • When assembling a single or an extended product, some parts maybe surplus.

  • These 2 icons below indicate if screw’s tightening is required or not.

  • Temporary tightening of a few screws may be needed to prevent a profile from sliding out.

  • Tighten all screws once assembly is completed.

IMPORTANT ASSEMBLY STEPS

When encountering this information icon during assembly, please refer to the relevant assembly step for important additional comments.

Step 5: It is recommended to place a sheet / Carton below the parts to avoid scratches and peeling of paint.

Step 5-6: According to the desired drainage direction, please select the preferred side to place the shorter legs. Please verify both legs #8002 are mounted on the same side

Step 7: At the end of this step, tighten all screws in the carport.

Step 14: Perform gradually in accordance with the previous steps.

Step 17: Carefully apply silicone sealant along the inner cross-section of parts #7039 & #8119.

Step 21: Make sure parts #7580 (Step 18) are placed underneath each and every panel (supporting the panels’ edges).

Step 23: Level the poles with the foot-pads on to the flat surface, and then attach to the surface of your choosing using accordant screws and anchors.

Contents

Contents

Contents Continued

Illustration 1

Illustration 2

Illustration 3

Illustration 4

Illustration 5

Illustration 6

Illustration 7

Illustration 8

Illustration 9

Illustration 10

Illustration 11

Illustration 12

Illustration 13

Illustration 14

Illustration 15

Illustration 16

Illustration 17

Illustration 18

Illustration 19

Illustration 20

Illustration 21

Illustration 22

Illustration 23

Illustration 24

Illustration 25

Declaration of Performance

Documents / Resources

| CANOPIA 82816 Aluminium Carport Verona 5000 [pdf] Instruction Manual
82816 Aluminium Carport Verona 5000, 82816, Aluminium Carport Verona 5000, Carport Verona 5000, Verona 5000
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals