Luci 01607170 Theater Lighting Instruction Manual

operating instructions

Thank you for choosing a quality product from Luci Della Rivalta sol. We trust our products and services meet your requirements, but if not please contact us directly using the attached feedback form to help us improve our service quality.
This product has been manufactured with great care and left our factory in perfect conditions, but if it has been damaged in transport please contact your dealer in the first instance. A feedback form is appended. Our warranty covers all manufacturing and component defects for one year from the date you purchased the product.
Our products are designed for the use of professional technicians and operators only, and the instructions provided here ensure a safe and correct operation of this product. Luci Della Rivalta sol will not accept any responsibility where damage has been caused to the product or persons through improper use of the product and/or non-compliance with the regulations described herein

IMPORTANT: Read these user instructions before using this lighting unit

The instructions given here ensure a safe and correct usage of this product. A user’s failure to comply with the installation, operating, maintenance and safety procedures mentioned in this manual, as well as those generally applicable to this lighting equipment, may cause the unit not to perform as expected.

Luci della Ribalta accepts no liability for direct, indirect, incidental, special, or consequential damages resulting from the customer’s failure to follow the installation, operating, maintenance and safety procedures in this manual or those generally applicable to lighting equipment.

The limitation extends to damages for personal injury, property damage, loss of operations, loss of profits, loss of product or loss of time, whether incurred in by the customer, the customer’s employees or a third party.

Apart from the instructions given on this manual, all relevant safety and health standards of the appropriate Directives of the country where the unit will be installed must be complied with.

IMPORTANT SAFETY NORMS

• This product is a professional lighting fixture, namely a follow spot, fitted with a LED light source, which can only be operated by professional staff
• Warning, high voltage ignition. Disconnect the unit from power before servicing
• Continuous mains power is required for this spotlight as an internal dimmer controls the intensity via DMX or local rotary knob. An accessory clamp‐on digital dimmer, for positioning on the side grab handles of the followspot, is furthermore supplied to locally control the dimming
• Use of a phase control dimmed mains supply may damage the internal electronics
• This product features fan‐assisted ventilation. Make sure you do not cover the fans or obstruct the air flow at any time
• Make sure all fans are working correctly at any one time. Should you detect even the slightest malfunction, switch the luminaire off and carry out the necessary servicing. Replace the fans if necessary
• This product is rated IP 20 and is therefore designed for interior use only. For details on maximum ambient temperature and tilt angle please refer to what indicated on the product label or screen‐printing on the side of the lens‐tube or the rear of the LED‐house
• Repairing and replacement of any component of this product must be carried out exclusively by professional personnel in conformity with the relevant safety and health standards and only with original Luci Della Rivalta srl components
• Replacement of any part of the wiring system must be carried out exclusively by professional personnel in compliance with the original wiring diagram and with components identical to or compatible with those originally fitted
• Installation of this product must be exclusively carried out by professional personnel in compliance with the safety norms in force in the country where the product is used

WARNING: DANGER OF ELECTRICAL SHOCK DO NOT OPERATE ON LIVE EQUIPMENT

• Disconnect power before opening this fixture to access its light source or electronics.
• The replacement of the LED source or any of its electronic components can be carried out exclusively by professional personnel upon LDR’s written authorization and only with original Luci della Ribalta srl components. Failure to obtain the manufacturer’s authorization to carry out the replacement/repair, will immediately invalidate the product’s warranty

WARNING: EYE DAMAGE HAZARD
Make sure this fixture is installed so as to avoid prolonged direct staring at its operating light source (LED) from a distance of less than 7m / 23ft.

WARNING: FIRE HAZARD

• Never locate this fixture on any flammable surface.
• Minimum distance of any part of the body of the luminaire from any flammable surface or object: 0,5m / 20in
• Minimum distance from lit surface, please refer to product label
• Make sure the mains power supply the fixture will be connected to is protected by a suitable thermal magnetic circuit breaker

BOX CONTENT

A. Standard follow spot
Astro follow spot in the chosen model Separate 6-colour color changer unit
Mains power cable with Power-Con
Fitted Ø28mm/1.12in spigot with fluid head
Fitted iris diaphragm
Mobile clamp-on dimmer

Kit follow spot
Astro f-stop in the chosen model in flight case
Separate 6-colour color changer unit
Mains power cable with Power-Con
Separate Ø28mm/1.12in spigot with fluid head
Fitted iris diaphragm
Mobile clamp-on dimmer
Black follow spot tripod

WEIGHT AND DIMENSIONS

ASTRO 600 3200K and 6000K
net weight: 31 kg + 1,2 kg colour changer
gross weight: 36 kg
packing dimensions: 1x 115x46x46h cm + 2x 31x26x15h cm (spigot with fluid head + colour changer)

MOUNTING THE SPIGOT ‐ # A20102100

This product is a follow spot meant for tripod‐ or pole‐mounting only and is therefore not fitted with any secondary fixing point. Do not hang it.
A ø28mm/1.12in spigot with fluid‐head is supplied in standard delivery for you to tripod‐mount your To mount the spigot please refer to the relevant instruction manual supplied with this part (separate box)

MOUNTING THE COLOUR CHANGER (supplied, part nr. 20105206)

The Astro 600 comes with a 6‐colour colour changer unit which is packed separately in an outer box or in the flight case and needs to be fitted to the lens‐tube of your follow spot as follows:

• Mount the colour filters on the colour changer units. See relevant instructions supplied with the colour changer
• At the front of the followspot, slacken the 3 cross‐head black M4 screws (two at the top angles, one at the bottom, left‐hand side angle) so that they remain inserted approximately half‐way through
• Position the colour changer unit on the front plate of the followspot, making sure that the colour levers are positioned on the left‐hand side of the follow spot when viewed from the front and hang it to the previously positioned screws
• Release the colour filters of the colour changer by pressing the black, flat lever in order to have access to the screws
• Insert a M4 Phillips screws driver at least 12cm long in each one of the holes provided at the front of the colour changer and tighten each screw
• Ensure the colour changer unit is secure, and all three screws are tight

MOUNTING / REPLACING THE IRIS DIAPHRAGM ‐ supplied

The iris diaphragm supplied with the follow spot has 20 leaves to size the beam from a maximum aperture of 68mm/2.67in to a minimum of 5mm/0.19in. The iris comes already fitted, so you will only have to refer to this section in case you need to remove or replace the iris.

• Using a Phillips screw‐driver (M3) remove the cross‐head screws from the top lids of the gate area (2 lids, 2 screws each)
• Using a Phillips screw‐driver (M4) remove the two cross‐head screws from the sides of the iris plate
• By pulling (to remove) or pushing (to insert) from the lever handle, slide the iris diaphragm out / in the gate area
• Fix the iris in position by tightening the previously removed screws
• Re‐position the top lids and fix the M3 screws

Important notice: do not leave the iris totally closed for over 5 minutes while the LED is on

FAILURE TO COMPLY WITH THE ABOVE NOTICE MAY CAUSE THE IRIS AND THE FOLLOWSPOT TO SUFFER MAJOR HEAT DAMAGES AND WILL INVALIDATE THE PRODUCT WARRANTY

GOBO HOLDER (accessory, part nr. A20100808)

The gate area of the ASTRO 600 can accommodate a gobo holder for B‐size metal gobos. The gobo‐ holder sits in front of the iris diaphragm and they can be used simultaneously. The gobo‐holder is not part of the standard delivery and must be ordered separately. In order to fit the gobo holder:

• Using a Phillips screw‐driver (M3) remove the cross‐head screws from the top lids of the gate area (2 lids, 2 screws each)
• Remove the two M4 screws fitted to each side of the gobo holder
• By pushing from the lever handle, slide the gobo‐holder in the gate area. The bent top‐lid of the gobo holder must overlook the inner part of the gate area
• Fix the gobo‐holder in position by tightening the previously removed screws
• Re‐position the top lids and fix the M3 screws

ADJUSTING THE YOKE

This followspot is provided with a yoke balancing adjustment. The balancing point is factory set for the standard product configuration supplied (with 6‐colour colour changer). However, should you need to adjust the balancing, please follow the procedure here below:

• The followspot must be mounted on the tripod stand with all relevant accessories attached
• Using a Phillips screw driver, slightly loosen the 2 M5 screws on each side of the yoke
• Gently slide the followspot backwards or forwards to the required position by using both hands. Make sure you always hold the followspot with at least one hand to prevent the heavy LEDhouse to suddenly bend downwards
• Make sure the yoke is correctly aligned horizontally
• Lock the tilt‐lever
• Tighten the 4 M5 screws

MPORTANT NOTICE BEFORE THE INSTALLATION / INSTALLATION

This fixture is meant for tripod‐mount installation only. No hanging is allowed Before installing this fixture check its weight on the product label and the weight of each accessory
you are adding and make sure the structure you are installing it to withstands the total weight.
The mounting stirrup is designed to allow the spotlight to be fitted to a suitable tripod or pole.

CAUTION
DO NOT TURN THE LUMINAIRE UPSIDE‐DOWN AND MAKE SURE THE STIRRUP ALWAYS SITS DOWNWARDS

Note: the fixture’s location must provide suitable ventilation for the LED module.

WIRING

Before being connected to the mains power, this unit may need to be wired with a suitable plug if not already installed. Make sure the plug you are using is rated for the product’s power load.

This fixture must be grounded
Ensure the plug conforms to the relevant EU/UL or local electrical standards

To perform a correct wiring, please note that the cores in this mains lead are colour‐coded as follows:

Ground: green+yellow – Neutral: blue ‐ Phase: brown

In case the colours of the wires do not correspond to the colour of the connection points on your plug, please proceed as follows:

• The green or green and yellow wire must be connected to the connection point marked with the letter E or with the symbol   or cultured in green or in green‐yellow
• The blue wire must be connected to the connection point marked with the letter N or cultured in black
• The brown wire must be connected to the connection point marked with the letter L or coloured in red

Before you finally position this product for use, temporarily connect it to a properly fused power supply to check the unit works correctly.

VOLTAGE

Before operating this unit please refer to the product label mounted at the back of the luminaire to check you are operating with the correct voltage. The Astro 600 LED can be operated between 100V and 260 VAC.

FREQUENCY

Frequency on this product is automatically selected by the electronic PSU (50/60Hz).

CONNECT TO THE POWER SUPPLY

• Connect the unit to a continuous mains power source
• Make sure the power supply is protected by a suitable thermal magnetic circuit breaker
• This fixture must be grounded

MECHANICAL OPERATION

Focus control: this fixture features a variable beam angle from 7° to 12° which can be controlled through the two control knobs on the right‐hand side of the lens‐tube.
The variable beam is modified by adjusting the front and rear zoom lenses in relation to each other.
The front lens defines the beam spread, the rear lens defines the focus degree of ‘softness’ or ‘hardness’ of the beam edge or shutters.
Gently turn the knobs anti‐clockwise until you have reached the desired size/focus of the beam in relation to the distance you are projecting at.
Turn the knobs clockwise and tightly close them so that the lenses are held in position at any tilt angle
Beam‐sizing: the size of the beam is controlled using the supplied iris diaphragm
Beam‐dimming and black‐out: this followspot can be dimmed and backed‐outby:

• Local manual control, rotary switch on the backplate of the unit
• Local, via clamp‐on digital dimmer, supplied – see relevant instructions
• Remote, by DMX512 signal

CAUTION: Make sure you always use the one of the above options to black‐out the light and never the sizing iris diaphragm as keeping the latter closed may cause overheating, damage and even fire inside the LED‐house.
Pan & Tilt control: this unit is fitted with 2 soft, comfortable side bars covering the full length of the followspot for an easy and safe control of the pan and tilt angle by the followspot’s operator from any position
The stirrup is factory‐balanced and fitted with a positive friction clamp controlled by a user‐friendly, effective lever‐knob. Turn the knob anticlockwise to release it, position the followspot at the desired tilt angle and turn the knob clockwise to hold the desired position.
Press the button at the top of the lever and keep it pressed while turning the lever if you need to change its position.

LOCAL CONTROL PANEL AND OPERATION

OPERATION: LCD display for DMX address, system setup and status details.
POWER: power LED status indicator, red colour. ON= power
DMX: DMX LED status indicator, green colour. LED OFF = DMX OFF and manual control activated,
LED ON = DMX MODE activated with no DMX signal, FLASHING LED = receiving DMX
MENU: rotary switch selector to select and modify the operational modes. Turn left or right to navigate through the menu and press to select or to confirm
DMX IN: input DMX signal (pin1=0, pin2= DATA‐, pin3=DATA+).
DMX OUT: Loop through DMX signal output
POWER IN: Mains power input
POWER OUT: Mains power output

MENU

There are fourteen different menus to control the settings of the ASTRO 600W LED. The rotary selector is used to adjust the settings and to navigate through the menu. Turn left or right to select the menu and push to access or to confirm the selected data or functions. To exit the selected menus without saving the data, press the rotary selector for at least 1 second.

DMX OR MANUAL (Mode)

Select the LED control mode between DMX (factory setting) and manual. To change the control mode press once the rotary selector until an arrow () appears on the menu. Turn the selector to the right or the left to select the desired mode of operation and press to confirm your selection.

Tap the rotary selector and the LCD screen will display the mode status and the current value:

DMX ADDRESS (Addr)

It allows to select the initial DMX starting address to remotely control the LED functions. To change the initial DMX address press the rotary switch until an arrow appears, then turn to  change to the desired DMX starting address. Press to confirm your selection. Factory setting is 001.

DIMMER RESOLUTION (8/16b)

The dimming resolution can be controlled at 8 bits from one DMX channel to 16 bits with 2 DMX
channels. Factory setting is 8 Bit.

LOST DMX SIGNAL (DMXMem)

In case of signal failure this function allows to store in memory the last DMX value.
Factory setting is ON. Three options are available:

TROBE (Strobe)

This function enables to activate the strobe function. Factory setting is DISABLE.

STROBE SPEED (SetStr)

It allows to set the strobe speed. This menu is not active when the strobe function is disabled or when it is remotely controlled through DMX. Factory setting is OPEN.

DIMMING CURVE (Curves)

This function allows to select a response curve for the Astro LED. A choice of two curves is available: Square and Linear. Factory setting is SQUARE.

CUT OFF DIMMING RESPONSE (CutOff)

This function allows to select a LED behavior simulating a tungsten or halogen lamp during the dimming cut off.
Factory setting is SLOW

DIMMING BEHAVIOUR (Smooth)

This function allows to set the LED dimming response. Factory setting is NORMAL.

LCD SCREEN ILLUMINATION (BackL)

This function allows to turn off the LCD backlight, the LED POWER and LED DMX after 1’30” from the last setting. Factory setting is Auto OFF.

TEMPERATURE CONTROL (TBoard)

This function allows to visualize the Board temperature. Factory setting is °C.

TEMPERATURE CONTROL (Tled)

This function allows to visualize the LED temperature. Factory setting is °C.

SOFTWARE VERSION (SwVer)

This function allows to visualize the software version.

MANUAL DIMMER TYPE (Manu)

This function allows to select the manual dimmer type. The Astro 600 is supplied with a mobile clamp‐on digital dimmer which can be clamped‐on in any position of each of the side control bars and needs to be set as follows.
Factory setting is ENCODER.

HIDDEN MENUS

There are also four different hidden menus to select the advanced settings of the ASTRO LED. To activate this function turn the Astro OFF and then ON again by pressing the rotary switch at power on.

A PRO or BASIC CONTROL (ProBasic)

The PRO‐BASIC control is a special function which allows to limit the access to the control menu. Select ProBasic with the rotary switch and press to access the menu.

Select:

• PRO, to enable access to all the functions
• BASIC, to limit the access to functions 16.1 DMX or MANUAL MODE, 16.2 DMX ADDRESS, 16.11‐16.12 Temperature Control and 16.13 Software version.

Factory setting is PRO.

FACTORY SETTINGS (Reset)

The RESET control is a special function which allows to RESET the product to factory settings

ID REMOTO (ID Rem)

It allows to select the ID number to connect the Astro to Remote (available as a separate accessory under part # A20702072) a device which allows to upload and download firmware. To change the initial ID press the rotary switch until an arrow appears, then turn to change to the desired ID number. Press to confirm your selection. It is possible to select an ID number from 0 to 250. If ID number=0 remote control is not active.
Factory setting is 000.

CALIBRATION (Set Min)

It allows to calibrate the minimum level of the output.

EXIT HIDDEN MENU (Exit)

It allows to exit from the hidden menus.

CLEANING AND MAINTENANCE

To ensure maximum performance of the product, a regular maintenance service should be carried out. Please make sure the product is cold and disconnected from power supply when doing this.

General maintenance

• Clean all reflective parts such as lenses opening the product, if necessary.
• Check the lenses and replace any visibly damaged component.
• Clean air ducts and fans in order to allow proper ventilation activity on the product.
• Check internal and external wiring and replace any cable which should be damaged by heat or mechanical agents.

Cleaning of optical components LEDhouse lenses:

• Open the lens compartment lid by removing the two M4 cross head screws at the rear of the led‐house tube and slide the top lid free
• Remove the condensor lenses assembled block by removing the two M5 cross head screws.
• Clean the lenses with a soft cloth and re‐position

Zoom lenses:
Slide the front zoom panels positioned at the bottom of the lens tube and clean with a soft cloth.

SPARE PARTS

All components are available as spare parts. We strongly recommend you always use original LDR components as spare parts. Please refer to our technical assistance should you need to order and/or replace any part of the unit.

WARRANTY

Our warranty covers all structural and manufacture defects for two years from the date you purchased this product. In case of complaints we strongly recommend you use the complaint form at the end of this manual or contact the local dealer who supplied the product to you. In any case please report the serial number of the product.
In case of complaints under warranty proof of purchase will have to be provided.

AVAILABLE ACCESSORIES

A20100106: 185x185mm colour frame
A20109106: Kit 185x185mm colour frame + front runners
A20105106: 5‐colour colour changer magazine
A20105206: 6‐colour colour changer magazine
A20100707: Spare iris diaphragm
A20100808: B‐size gobo holder for metal gobos
A20102100: Spare fluid‐head spigot for followspot tripod
A20102200: Spigot for tripod
A20102311: HD steel tripod with fluid head
A20102401: Black followspot tripod
A20102402: Chrome‐plated followspot tripod
A20107180: Flight‐case with braking wheels, stackable
A20202401: Set of 3 braking wheels for followspot tripod
A20702071: Side‐handle clamp‐on digital dimmer
A20702072: Remoto control unit for software upgrade
V90MLRT100FR: Braking wheel (1pc) for flight case

 SUMMARY OF CONTROLS AND FUNCTIONS

#| Function| Description| Available Options| Factory Setting
---|---|---|---|---
1| Mode| MANUAL or DMX control| MANUAL (controlled from the rotary switch or slider); DMX| DMX
2| Addr| Selects the DMX starting address; other remotely controlled functions are assigned in sequence to the 1st assigned DMX address| From 001 to 512| 001
3| 8/16b| 8 or 16 Bits dimming resolution| 8 BITS on 1 channel; 16 BITS on 2 channels| 8 BITS
4| DMXMem| Sets the behaviour of the unit in case of DMX failure| ON = last DMX value; OFF=80% fade to 80% after 1,5 Sec; OFF=0%| ON
5| Strobe| Activates the Strobe function| ENABLE ; DISABLE| DISABLE
6| **SetStr| Selects the Strobe speed. This menu is inactive when the Strobe function is disabled or when remotely controlled through DMX| OPEN = ON ; SPEED = ## (select value from 01 slowest to 10 fastest); CLOSED = OFF| ****OPEN
7| Curves| Selects the dimming curve| SQUARE ; LINEAR| SQUARE
8| CutOff| Replicates the halogen lamp dimming behaviour at cut off| FAST = NOT ACTIVE ; SLOW = ACTIVE| SLOW
9| Smooth| Dimmer response| NORMAL = 150ms; SLOW = 300ms FAST = Immediate response| NORMAL
10| BackL| LCD screen retro‐illumination| ON ; Auto OFF = LCD light off after 1’30”| AutoOff
11| TBoard| Visualizes the Board temperature| Selects the LED Temp in °C or F°| °C
12| Tled| Visualizes the LED temperature| Selects the LED Temp in °C or F°| °C
13| SwVer| Visualizes the software version| | ‐‐‐
14| Manu| Selects the manual dimmer type| ENCODER = Rotary switch POTENT = External slider| ENCODER
SPECIAL FUNCTIONS: to activate these functions press the rotary switch at power on**

| Function| Description| Available Options| **Factory

Setting
A| ProBasic| Sets the functions available from the control menu| PRO = Enables access to all functions; BASIC = Limits the access to:1 Mode, 2 Addr, 11 T Board, 12 Tled and 13 Sw Ver| PRO
B| RESET| Factory RESET| Returns to factory settings| ‐‐‐
C| ****ID Rem| Sets the ID number to activate the Remoto control unit to upload and download firmware| From 000 (no remote control) to 250| 000
D| Set Min| Sets the minimum level of theoutput| From 000 to 9999| ‐‐‐
E| Exit| Exits from hidden menus| | ‐‐‐**

DMX CHARTS

DMX chart 1 (16 bit dimmer and strobe disabled)
This DMX chart refers to the followspot set at default parameters

DMX Channel| Function| Type of Control| Effect| Decimal| Percentage
---|---|---|---|---|---
1| Master Dimmer| Proportional| Adjusts luminous output intensity from 0 to 100%| 0| ‐| 255| 0%| ‐| 100%
Projector: Astro 600W White| Table name: DMX512 Functions chart 1 (default)| Issue: 1| Date: 13/11/2019

DMX chart 2 (16 bit dimmer enable, strobe disabled)

This DMX chart refers to the followspot set with 16 bits resolution (See chapter 16.3 of this user guide).

DMX Channel| Function| Type of Control| Effect| Decimal| Percentage
---|---|---|---|---|---
1| Master Dimmer| Proportional| Adjusts luminous output intensity from 0 to 100%| 0| ‐| 255| 0%| ‐| 100%
2| Dimmer Fine| Proportional| Fine dimmer control 16 bit| 0| ‐| 255| 0%| ‐| 100%
Projector: Astro 600W White| Table name: DMX512 Functions chart 2 (16 bits)| Issue: 1| Date: 13/11/2019

DMX chart 3 (Strobe function enable, 8 bit dimmer)

This DMX chart refers to the follow spot set with strobe function active (See chapter 16.5 of this user guide

DMX Channel| Function| Type of Control| Effect| Decimal| Percentage
---|---|---|---|---|---
1| Master Dimmer| Proportional| Adjusts luminous output intensity from 0 to 100%| 0| ‐| 255| 0%| ‐| 100%
2| Spare Channel| Step| No effect| 0| ‐| 255| 0%| ‐| 100%
3| Strobe| Step| Open| 0| ‐| 20| 0%| ‐| 8%
Step| Strobe speed 1 (minimum frequency)| 21| ‐| 40| 9%| ‐| 15%
Step| Strobe speed 2| 41| ‐| 60| 16%| ‐| 24%
Step| Strobe speed 3| 61| ‐| 80| 25%| ‐| 31%
Step| Strobe speed 4| 81| ‐| 100| 32%| ‐| 39%
Step| Strobe speed 5| 101| ‐| 120| 40%| ‐| 47%
Step| Strobe speed 6| 121| ‐| 140| 48%| ‐| 55%
Step| Strobe speed 7| 141| ‐| 160| 56%| ‐| 63%
Step| Strobe speed 8| 161| ‐| 180| 64%| ‐| 71%
Step| Strobe speed 9| 181| ‐| 200| 72%| ‐| 78%
Step| Strobe speed 10 (maximum frequency)| 201| ‐| 220| 79%| ‐| 86%
Step| Closed| 221| ‐| 255| 87%| ‐| 100%
Projector: Astro 600W White| Table name: DMX512 Functions chart 3 (Strobe)| Issue: 1| Date: 13/11/2019

DMX chart 4 (16 bits dimmer and Strobe enabled)

This DMX chart refers to the followspot set with 16 bits resolution and strobe function active (See chapter 16.3 and 16.5 of this user guide).

DMX Channel| Function| Type of Control| Effect| Decimal| Percentage
---|---|---|---|---|---
1| Master Dimmer| Proportional| Adjusts luminous output intensity from 0 to 100%| 0| ‐| 255| 0%| ‐| 100%
2| Dimmer Fine| Proportional| Fine dimmer control 16 bit| 0| ‐| 255| 0%| ‐| 100%
3| Strobe| Step| Open| 0| ‐| 20| 0%| ‐| 8%
Step| Strobe speed 1 (minimum frequency)| 21| ‐| 40| 9%| ‐| 15%
Step| Strobe speed 2| 41| ‐| 60| 16%| ‐| 24%
Step| Strobe speed 3| 61| ‐| 80| 25%| ‐| 31%
Step| Strobe speed 4| 81| ‐| 100| 32%| ‐| 39%
Step| Strobe speed 5| 101| ‐| 120| 40%| ‐| 47%
Step| Strobe speed 6| 121| ‐| 140| 48%| ‐| 55%
Step| Strobe speed 7| 141| ‐| 160| 56%| ‐| 63%
Step| Strobe speed 8| 161| ‐| 180| 64%| ‐| 71%
Step| Strobe speed 9| 181| ‐| 200| 72%| ‐| 78%
Step| Strobe speed 10 (maximum frequency)| 201| ‐| 220| 79%| ‐| 86%
Step| Closed| 221| ‐| 255| 87%| ‐| 100%
Projector: Astro 600W White| Table name: DMX512 Functions chart 4 (16 bits +Strobe)| Issue: 1| Date: 13/11/2019

Luci della Ribalta srl reserves the right to modify the present document without prior notice.

References

• [ L.D.R. - Luci della Ribalta - ]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>