LUCI LV.6000 Inox Kitchen Laundry Mixer Instruction Manual

LUCI LV.6000 Inox Kitchen Laundry Mixer

Product Specifications

• Model: LV.6000
• Brand: Verotti
• Contact: T 1300 837 688, E [email protected]

Product Usage Instructions

Parts Identification
The product consists of various numbered parts for identification. Refer to the list below to identify each part:

1. Part 01: KRD501-01
2. Part 02: KRD501-02
3. Part 03: KRD501-03

Luci Installation Instruction
Follow these steps to install the Luci component of the product:

1. Refer to the Luci Installation Manual provided separately.
2. Ensure all parts are correctly identified before installation.
3. Proceed with the installation as per the Luci Installation Instruction manual.

Frequently Asked Questions (FAQ)

• Q: How do I obtain the Luci Installation Manual?
  A: The Luci Installation Manual is provided separately. If you have not received it, please contact our customer service at T 1300 837 688 or E [email protected] .

• Q: What should I do if a part is missing or damaged?
  A: In case of missing or damaged parts, please contact our customer service immediately for assistance in obtaining replacement parts.

• Q: Can I modify the product during installation?
  A: It is not recommended to modify the product during installation, as it may affect its functionality and warranty. Follow the provided instructions carefully for proper installation.

LUCI INSTALLATION INSTRUCTION
LV.6000 IMPORTANT!
Please read this instruction Prior to installation

T 1300 837 688 E [email protected] www.verotti.com

PARTS IDENTIFICATION

INSTALLATION

1. Flush the pipe work thoroughly prior to installation.
2. Tighten the threaded fixing housing (Part 12) into the base of the mixer ensuring fixing housing is secure
3. Screw the cold only flexible tail (Part 7) into the underside of the mixer body and hand tighten .
4. Fit O-Ring (Part 9) into the underside of groove on the base flange (Part 8) .
5. Centre the Base Flange + O-Ring (Part 8+9) centre of the hole of Basin or Bench top prior to positioning the Mixer
6. Place the Basin Mixer Into the groove on the base flange carefully position the threaded fixing housing and Cold Flexi Tail into the Hole of the basin or bench top .
7. Hold the mixer in place at the top of Basin or bench top and position the rubber washer (Part 10) and then the Metal Washer (Part 11) over the threaded housing on the underside of basin or bench top
8. Ensure Mixer is in correct position and hand tighten the Fixing Nut (Part 13) over the threaded housing ensuring the rubber washer compresses at the underside of the basin or bench top. A screw driver may be required to provide additional torque to the fixing nut to ensure it is tightened adequately .
9. Once basin mixer is in position and tightened , feed the hot flexi (Part 7) into the underside of the mixer body and hand tighten .
10. Connect the flexible tails to firmly to the to the water supply connection , Turn on the water supply on and check for any leaks

IMPORTANT RECOMMENDATIONS FOR INSTALLATION

• Installation should comply to AS/NZS3500.1 2003 or relevant local requirement.
• Not suitable for gravity feed application.
• Hot & cold water inlet pressures should be equal.

1. WATER PRESSURE
   Operating static pressure is 150 – 500kpa. If pressure exceeds this, then an approved pressure limiting valve must be installed.

2. PRE-FLUSH

3. Always flush out the pipework before connecting any faucets.

4. Damage caused to the faucet by debris coming through the

5. pipework is not covered under warranty.

6. WATER TEMPERATURE
   Maximum hot water temperature is 75 degree.

7. STOP TAP
   Angle valves are recommended

ATTENTION!
Failure to do so will void the warranty.

References

• Verotti Bathroom Culture

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>