better bathrooms BeBa 27953 Chrome Heated Towel Rail Radiator User Manual

better bathrooms BeBa 27953 Chrome Heated Towel Rail Radiator

Product Information

The Sahara Towel Radiator is a multi-person assembly radiator designed to provide warmth and functionality in your bathroom. It comes in various product codes with different BTU (British Thermal Unit) and wattage specifications to suit your heating needs.

Specifications

Parts
The radiator comes with the following parts:

• A. 1 x Radiator
• B. 1 x Air Vent (Bleed Valve)
• C. 1 x Blanking Cap
• D. 4 x Wall plug
• E. 4 x Wall Bracket
• F. 4 x Washer
• G. 4 x Wall screw
• H. 4 x Grub Screw
• I. 4 x Pair Rail Bracket Part 1
• J. 4 x Pair Rail Bracket Part 2
• K. 4 x Connecting Screw

Product Usage Instructions

Tools Required

• Spanner
• Allen Key
• Flathead screwdriver
• Philips screwdriver
• Tape measure
• Drill and 8mm drill bit
• Spirit Level
• Pencil
• Sealing tape

Installation
Please note: Before starting any installation, turn off the water supply. Also, ensure that no pipes or wires can be damaged in the desired location before drilling.

1. Prepare the water supply pipes to match up with the towel radiator and valve dimensions being used.
2. Fit the blanking cap and air vent in the top of the rail, securing them with a little sealer tape. Use a spanner to tighten them, being careful not to overtighten.
3. Set the position of the wall brackets approximately 50mm in from each side of the rail. Mark these positions on the wall in the required location. Use a spirit level to ensure they are horizontally and vertically aligned.
4. Drill into the marked positions using an 8mm drill bit. Insert the wall plugs and tap them flush to the finished wall surface. If drilling into a tile, it is recommended to tape the wall to prevent the drill from slipping.
5. Position the wall brackets and screw them into place using the screws provided, securing each with a washer and a Philips screwdriver.
6. Place the first section of the rail bracket (Part 1) around the bars of the towel rail. Then, slide the middle section of the rail bracket (Part 2) over the first section connected to the bars. Secure them using the smaller screws provided.
7. Once both parts of the rail brackets are fitted, align and push the rail brackets on the radiator onto the wall brackets secured to the wall. Ensure that there is an equal distance from the wall to connect to the supply pipes. Secure each bracket set with the grub screw provided (insert through the slot in the bracket), being careful not to overtighten.

FAQ

• Can I install the Sahara Towel Radiator by myself?
  We always recommend using professional tradespeople to install your product for optimal safety and performance.

• What tools do I need for installation?
  The tools required for installation are a spanner, Allen key, flathead screwdriver, Philips screwdriver, tape measure, drill and 8mm drill bit, spirit level, pencil, and sealing tape.

• How do I prepare the water supply pipes for installation?
  Before commencing installation, ensure that the water supply pipes match up with the towel radiator and valve dimensions being used.

• Can I drill into tiles without damaging them?
  Yes, if drilling into a tile, it is recommended to tape the wall to prevent the drill from slipping and damaging the tile.

INTRODUCTION

• And welcome to our growing gang of sawy shoppers
• We’re on a mission to bring you extraordinary bathroom products, for less. From modern to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So, you can fall in love with your space every single day.
• As one of the UK’s largest independent bathroom stores, we’ve received countless awards; including the National Business Awards UK, the Digital Entrepreneur Awards and being placed on The Sunday Times Fast Track 100.
• We hope your new product exceeds your highest expectations. However, if you experience any problems, please:
  • call our friendly UK call centre on 0330 390 3062 (9am-7pm Monday to Friday, or 1 0am-4pm Saturday and Sunday), or
  • send us a message via customerservices@buyitdirect.co.uk

Important information

• Please read these instructions thoroughly and retain for future reference
• Manufactured to BS EN 442-1 Radiators and convectors
• Please ensure that the product is checked for damage prior to installation, any damage reported after installation will not be covered.
• The pipework must be flushed out to remove any debris which can affect the function of this product.
• A corrosion inhibitor should be used in your installation.
• BTU & Wattage info
  ** Product Code| BTU| Wattage| Product Code| BTU| Wattage**
  ---|---|---|---|---|---
  BeBa_25364| 478| 140| BeBa_26319| 928| 272
  BeBa_25365| 628| 184| BeBa_26321| 1099| 322
  BeBa_25366| 662| 194| BeBa_26322| 1102| 323
  BeBa_25367| 727| 213| BeBa_26324| 1344| 394
  BeBa_25368| 764| 224| BeBa_26327| 208| 610
  BeBa_25369| 812| 238| BeBa_27950| 454| 133
  BeBa_25370| 915| 268| BeBa_27951| 713| 209
  BeBa_25371| 1164| 341| BeBa_27952| 897| 263
  BeBa_25372| 1263| 370| BeBa_27953| 962| 282
  BeBa_25373| 1457| 427| | |

Parts

• A. 1 x Radiator
• B. 1 x Air Vent (Bleed Valve)
• C. 1 x Blanking Cap
• D. 4 x Wall plug
• E. 4 x Wall Bracket
• F. 4 x Washer
• G. 4 x Wall screw
• H. 4 x Grub Screw
• I. 4 x Pair Rail Bracket Part 1
• J. 4 x Pair Rail Bracket Part 2
• K. 4 x Connecting Screw
  Please note that Parts are for illustrative purposes only and may differ slightly to the actual product

Tools required

• Spanner
• Allen Key
• Flathead screwdriver
• Philips screwdriver
• Tape measure
• Drill and 8mm drill bit
• Spirit Level
• Pencil
• Sealing tape

Installation

Please note: Before starting any installation, turn off the water supply.
Please note: Before commencing any installation, the desired location should be checked before drilling, that no pipes or wires can be damaged.
First, prepare the water supply pipes to match up with the towel radiator and valve dimensions being used. Fit the radiator valve tail and nut into the towel rail (not supplied)(at both sides) and using sealing tape, tighten into position, then follow the installation below.

1. Fit the blanking cap and air vent in the top of the rail, (add a little sealer tape to secure) and tighten using the spanner, be sure not to overtighten.

2. Set the position of the wall brackets in relation to the size of your rail approximately 50mm in from each side and mark these positions on the wall in the required location. Use a spirit level to ensure these are horizontally and vertically aligned.

3. Using the drill and 8mm drill bit, drill into the marked positions then insert the wall plugs and tap flush to the finished wall surface.
   Please note: If drilling into a tile, it is recommended to tape the wall to prevent the drill from slipping.

4. Position the wall brackets and screw into place using the screws provided (securing each with a washer) with the Philips screwdriver.

5. Next, place the first section of the rail bracket (Part 1) around the bars of the towel rail, then slide the middle section of the rail bracket (Part 2) over the first section connected to the bars. Secure using the smaller screws provided.

6. Once both parts of the rail brackets are fitted, align and push the rail brackets on the radiator onto the wall brackets secured to the wall, ensure that there is equal distance from the wall to connect to the supply pipes. Secure each bracket set with the grub screw provided (insert through the slot in the bracket), be sure not to overtighten.
   Please note: You may need two people to connect the radiator, depending on the model purchased.

7. Finally, fit the radiator valves to the pipework and connect to the radiator valve tail and tighten all connections.
   IMPORTANT! The product is supplied un-filled.
   The rail should be filled with a water (80%) and glycol (20%) mixture if NOT being connected to the central heating system, also allow 5% air gap.

After installation

• After the above installation, turn on the water supply and using the flathead screwdriver, open the air vent via the central screw, open the inlet valve and let the water rush into the radiator. Check all connections for leaks.
• Once water overflows from the air vent, this means that there will be no air bubbles present.
• Use a screwdriver to close the air vent and then the radiator is ready to use.

Cleaning

• This radiator is made from steel with a painted finish. To maintain the surface of your product (especially when subjected to steam or splashes), wipe with a clean damp cloth and wipe dry.
• Do not use abrasive cleaning agents or materials which can strip and scratch the surface; the use of these agents or materials can invalidate your guarantee.
• It is recommended to wipe and dry on a regular basis.

For more information

• visit betterbathrooms.com
• email customerservices@buyitdirect.co.uk
• call 0330 390 3062
• write to Trident Business Park, Neptune Way, Huddersfield, HD2 1UA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>