REELCRAFT 5000 Series Air Water Hose Reel Instruction Manual

: June 15, 2024
: REELCRAFT

Table of Contents

Operating Instructions
- Series 5000 Spring Driven Hose Reels
  - Dimensions
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Operating Instructions

Series 5000 Spring Driven Hose Reels

Low Pressure Model Numbers:

5400 OLP 5630 OLP
5635 OLP 5600 OLP
5450 OLP

Dimensions

|

A

|

14 3/8”

---|---|---

B

| 14”
C|

9 3/4”

D

| 2 1/2”
E|

6 1/8”

SAFETY

Do not use reel at higher pressures or temperatures than listed on the back of this bulletin.
Remove all spring tension before beginning dissassembly process.

INSTALLATION:
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and binding.

MOUNTING:
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.

LUBRICATION:
Hose reel spring and bearings are factory lubricated and require no further lubrication.

REPLACING HOSE:

Wind spool flange clockwise-facing swivel-until spring is tight.
Back off three turns and latch.
Insert hose through roller guide.
Connect hose fitting to swivel joint and secure hose with clamps.

ADJUSTMENTS:
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is obtained.

REPAIRS:
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may void your warranty. Remove all spring tension before beginning disassembly process.

Form# 831-696 Rev: 2/2023

REELCRAFT 5000 Series Air Water Hose Reel 3

Item #

| Part #| # Req.| Description
---|---|---|---
1| S600886| 1|

Swivel Assembly

2

| 300031| 2| 1” Snap Ring
3| 300034| 2|

Spacing Washer

4

| S295-102| 3| 1/4” Plastite Hex Screw
5| 260022| 1|

Sheave Flange

6

| 500006| 1| Sheave Disk
7| S500019| 1|

Latch Cam

8

| S260648| 1| Spring Arbor
9| 300002| 7|

10-32 x 1/2” Screw

12

| S500107| 1| Guide Arm & Roller Assembly
13| 500101| 1|

Base Assembly

16

| S261360| 1| Spring Case Stud
17| 300006| 1|

3/8-16 x 1/2” Set Screw

18

| S500103| 1| Spring Case Assembly
19| S82-15| 8|

10-32 x 3/8” Nyloc Nut

20

| S400021 | 1| Latch Bumper
21| S32-136| 1|

10-24 x 3/8” Mach. Screw

22

| S400012| 1| Latch Bushing
23| S400018| 1|

Latch Spring

25

| 400020| 1| O-ring
26| S400109| 1|

Latch Plate Assembly

27

| 300035| 1| 10-32 x 1” Mach. Screw
29| 261650-1| 2|

1/4-20 Zinc Nyloc Nut

30

| S400015| 1|

Main Shaft

Item #

| Description| # Req.| 5400 OLP| 5450 OLP| 5600 OLP| 5630 OLP| 5635 OLP
---|---|---|---|---|---|---|---
10| Bumper Stop Assembly| 1| None| 1-HR1004-A| None| 1-HR1004|

1-HR1004

11

| Hose Assembly| 1| None| 601001-50 | None| S601011-30 | S601013-35
15| Drive Spring Assembly| 1| S503755| S503755| S504240| S504240|

S504240

28

| U-Bolt| 1| 3-117440| 3-117440| 3-117440| 3-117440| 3-117440

Hose I.D. and Length

| None| 1/4” x 50’ | None| 3/8” x 30’|

3/8” x 35’

Reel Inlet Connection

3/8” NPT(F)

Max. Operating Pressure|