RC FACTORY 2023 Buecker Young Master Instruction Manual

RC FACTORY 2023 Buecker Young Master

Product Information

Specifications

• Material: Various
• Length: Varies
• Width: Varies
• Thickness: Varies

Product Usage Instructions

Section 1: Wing Assembly

1. Take the completed wings with spars installed.
2. Use Thin CA glue to trim tabs to separate.
3. Apply Medium CA glue to attach L+R 4 pcs .8mm x 500mm (Aileron wing supports) on both sides.

Section 2: Aileron Bracing

1. Use Thin CA glue to attach L+R .5mm x3mm x 100mm braces on both wings.
2. Attach 2 pcs .8mm x 500mm (horizontal fuse runners) using Medium CA glue.
3. Attach .5mm x 3mm x85mm braces on both wings using Thin CA glue.
4. Grab the 1 pc of .5mm x 3mm x 330 cut to 85mm & 100mm. The rest of the cut should be 115mm in length and used for Step #31).

Section 3: Control Horn and Tube

1. Apply Thin CA glue to cut tube pieces and check fitment. Sand if necessary to ensure there is no binding in guides.
2. Slide control horn into place without gluing it yet.
3. Attach 2 pc’s .8mm x 500mm fuse lateral truss bracing on both sides using Medium CA glue.

Section 4: Vertical Top Fuse Brace

1. Attach 1 pc .5mm x 3mm x 115mm (left over cut from step #12) using Thin CA glue.

Section 5: Wing Strut Braces

1. Attach 2 pcs .5mm x 3mm x 200mm wing strut braces on both sides using Medium CA glue.

Section 6: Landing Gear Assembly

1. Attach 2 pcs 1.5mm x 2.5mm x 225mm (landing gear legs) using Thin CA glue.
2. Attach 2 pcs 1.5mm x 275mm landing gear braces on both sides using Medium CA glue.

Section 7: Control Rod Assembly

1. Cut 1.5mm x 30mm axle rods to 12mm in length.
2. Attach the axle rods using Medium CA glue.
3. Cut 1 pc 1.5mm x 40mm control rod assembly in half to get two 20mm pieces.
4. Attach the control rod assembly using Thin CA glue.

Section 8: Finishing Touches

1. Use Thin CA glue to attach clips to secure various parts.
2. Trim the .8mm x 500 (Elevator push rod) to the desired length.
3. Use Thin CA glue to attach heat shrink tubes and secure with clips.
4. Cut 2 pcs 1.2mm x 200 (around 190mm) and attach using Thin CA glue.
5. Trim the .8mm x 500 (elevator push rod) to the desired length.
6. Use Thin CA glue to attach clips and secure the push rod.

FAQ

• Q: What material is the product made of?
  A: The product is made of various materials.

• Q: How long is the product?
  A: The length of the product varies depending on the specific component.

• Q: How wide is the product?
  A: The width of the product varies depending on the specific component.

• Q: What is the thickness of the product?
  A: The thickness of the product varies depending on the specific component.

WHAT’S INCLUDE

Carbon fiber Included:

• 2 pc’s = .5mm x 3mm x 750mm
• 2 pc’s = .5mm x 3mm x 320mm
• 1 pc’s = .5mm x 3mm x 200mm
• 10 pc’s = .8mm x 500mm
• 1 pc = 3mm 330mm Tube
• 1 pc = 1mm x 330mm
• 4 pc’s = 1mm x 500mm
• 2 pc’s = 1.5mm x 2.5mm x 225mm
• 2 pc’s = 1.5mm x 275mm
• 2 pc’s = 1.2mm x 200

Carbon Fiber locations and size/cuts reference guide:

• 2 pc’s = .5mm x 3mm x 750mm (Step #2-3) Wing Spars
• 4 pc’s = .8mm x 500mm Step #8-9 (Aileron wing supports)
• 2 pc’s = .8mm x 500mm Step #12 (horizontal fuse runner supports)
• 1 pc’s = .5mm x 3mm x 330 Step #12 (horizontal fuse supports) (cut to 85mm & 100mm, rest of 115mm is for Step #31)
• 1 pc = 3mm 330mm Tube (Step #20)
• 2 pc’s = .8mm x 500mm fuse lateral truss bracing Step #24-26 (cut to length)
• 1 pc = 1mm x 330mm Step #29 (cut into two 160mm pieces)
• 1 pc = .5mm x 3mm x 115mm Step #31 (Vertical top fuse brace)
• 2 pc’s = 5mm x 3mm x 200mm Step #37 (wing strut braces)
• 4 pc’s = 1mm x 500mm Step 43-44 (Inner Wing to fuse bracing)
• 2 pc’s = 1.5mm x 2.5mm x 225mm Step 46-47 (landing gear)
• 2 pc’s = 1.5mm x 275mm Step 50 (landing gear braces)
• 1 pc = 1.5mm x 30mm Step 56 Axles (cut in half for 15mm)
• 1 pc = 1.5mm x 40mm Step 69 Control rod assemble (cut in half for 20mm)
• 1 pc = .8mm x 500 Step 76 (Elevator push rod)
• 1 pc = .8mm x 500 Step 83 (Rudder push rod)
• 2 pc’s = 1.2mm x 200 Step 88 (cut to size, around 190mm)

Hardware bag parts shown below

INSTALLATION

We wish you many happy flying hours with the Buecker Your RC Factory team.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>