MEILAN B08BRVHSXZ Blade Wireless Bike Computer Cycling Computer User Guide
- June 4, 2024
- MEILAN
Table of Contents
MEILAN B08BRVHSXZ Blade Wireless Bike Computer Cycling Computer
Installing the BLADE
Installing the Mount: F-mount and Bike Mount
The mount can be mounted on either the stem or the handlebar.
Installing the Bike Mount:
- Place the bike mount on the stem or handlebar of your bicycle with the rubber side down.
- Attach the bike mount securely using the two rubber bands.
- Place the Blade in the mounting grooves and turn clockwise until it locks in place. To remove, turn counterclockwise or clockwise and lift.
NOTE:
• Lock the mount firmly with two suitable rubber bands according to the size of the stem and handlebar.
• Two rubber bands fix the bracket diagonally.
• The triangle symbol in front must point in the direction of travel.
Installing the F-mount:
- Begin by removing the screw with the allen key from the F-mount.
- Select a suitable thickness of silicone pad into fixed ring of the mount.
- Place the F-mount and silicone pad around the handlebar.
- Replace and tighten the screw.
- Place the Blade in the mounting grooves and turn clockwise until it locks in place. To remove, turn counterclockwise or clockwise and lift.
NOTE : The F-mount double-sided available.
Installing the Speed and Cadence Sensor (C3)
-
NOTE : The battery insulator sheet needs to be removed for the first use in order to activate the sensor.
- Use a coin to twist the cover counter-clockwise until it is loose enough to remove (the arrow points to unlocked).
- Remove the cover, the battery and blue battery insulator sheet.
- Insert the battery with the positive side facing up. Use a coin to twist the cover clockwise back into place.
**Mounting the Speed and Cadence Sensor
**
-
Place the sensor on the rear chain stay of your bike, near the pedal. The logo should be facing up and the arm of the sensor should be inside the rear chain stay, facing down.
-
Loosen the sensor arm screw using a phillips screwdriver to move it into the correct position.
-
Secure the sensor in place with the provided rubber band or nylon ties, whichever is preferred. If using nylon ties, do not completely tighten yet, as the magnets still need to be aligned before completely securing the sensor in place. We recommend using the nylon ties for the most secure connection.
-
Attach the magnet:
-
Cadence magnet:
A. Remove white liner on the back of cadence magnet and place the pedal magnet onto the crank, magnet facing in towards the sensor.
B. Align so that the magnet will pass by the indicator sensing area on the body of the MEILAN C3 sensor.
C. The magnet will have to within 0.79 inch (about 2cm) to get a reading.
D. Attach the pedal magnet to the crank arm using two nylon ties. As such, adjust the position of the sensor if required. -
Wheel magnet:
A. Screw the wheel magnet onto any spoke on your back wheel, facing in towards the sensor.
B. Align so that the magnet will pass by the indicator line on the arm of the MEILAN C3 sensor.
C. The magnet will have to pass within 0.79 inch (about 2cm) to get a reading.
D. Once again, adjust the position of the sensor and/or magnet if required. Tighten the magnet in place on the spoke.
E. Once satisfied with the magnet positioning and tighten.
Setting up the Blade
The first time that you use this product, perform the initial setup from the Blade or from a smartphone (MEILAN app).
Setting up with Blade
-
Hold left-side button to power on/off.
-
Press SETTING key and go to setting menu.
NOTE : Press (middle key) to change the data; Press (left key) to scroll forwards through the functions; Press (right key) to Scroll backwards through the functions. -
Press to change the Time, Year and Date based on your current location. Press to confirm and scroll backwards. Please refer to Figure 03.
-
Press to change the measurement unit: ODO (KM/MI) and WGT (KG/LB), Press to confirm and scroll backwards. Please refer to Figure 04.
-
Press to change the default settings for ODO. Press to confirm and scroll backwards. Please refer to Figure 05.
-
Press to change the default settings for WGT. Press to confirm and scroll backwards. Please refer to Figure 06.
-
Pair with the sensors (speed and cadence sensor c3)
The icons are blinking on the screen. Meanwhile, rotate the wheel to activate the sensor. For detailed explanations on how to pairing with speed and cadence sensor C3. Please refer to the Pair Sensors on (page 5) -
After BLADE is paired with C3 (The icons on the screen stop blinks), press to enter WS (Wheel circumference) setting screen. Press to change the default settings for the wheel circumference, press to confirm and scroll backwards through enter the second bike pairing. * Set tire circumference : Refer to “Tire circumference table”( page 9 )
-
You can pair and set wheel circumference just like the first bicycle (If you have second bike). If not, you can press SETTING key to save and complete the Blade setting.
Restore Factory Settings
Long press ‘Power’ and ‘SETTING’ key at the same time, go to factory default settings menu. * All the data will be deleted when the device is reset to the factory default mode by pressing ; if you want to cancel the operation, you can press.
Setup with a Smartphone ( MEILAN app)
- Download the MEILAN app (download from Google Play or App Store) and ensure Bluetooth is on.
- Turn on MEILAN app to register / log in, follow the app instructions, select the measurement unit and authorize app.
- Turn on Blade: hold left-side button to turn on.
- Tap ‘+Add device’ to search and add Blade to the app. Please refer to Figure 01 to 04.
- Tap icon of “BLADE” to enter the setting menu, then set ODO and update firmware (if prompted). Refer to the Figure 05 to 07.
- Pairing sensors. Tap the sensor, search and add sensor, Meanwhile, rotate the wheel to activate the sensor. Refer to the Figure 08 to 10.
- After the paired, set or modify the name of sensor and wheel circumference, then complete the setting. Refer to the Figure 11 to 12.
- Tap “More”, you can switch units and authorize third-party apps: Strava, Trainingpeaks (Blade does not support Komoot app). Refer to the Figure 13 to 16.
NOTE:
- Time setting: After connecting to the app, the time is automatically synchronized with the phone time.
- When you in update device software process, don’t turn off your phone and bike computer, and do not exit the update menu, Otherwise your bike computer may be damaged.
Pair Sensors
Blade can be used with wireless Bluetooth BLE or ANT+ sensors. Pair your Blade with compatible speed and cadence sensor, heart rate monitor and power meter.
- The unit switches to the pairing standby screen and the icons are blinking on the screen.
- Use one of the methods in the following table to activate the sensor.
- Measurement icons will stop blinking when available sensors are paired. When all the sensors of speed, cadence, heart rate, and power meter are paired, the Blade interface will display SUCC. Therefore, when your sensors has stopped flashing, it means that the pairing has been successful. You can confirm and enter the next step to set the wheel circumference.
NOTE: If Blade has been paired and connected with the sensor before, it will prompt before entering the pairing: means your Blade is clearing its paired history, and ready to repair, press to confirm the clearing and re- enter the repair.
Starting a Workout
Display Screen
Starting Measurement
- Heart rate data will not be displayed unless heart rate sensor (Optional) is paired.
- Power data will not be displayed unless power meter (Optional) is paired.
-
Press to start recording.
-
Press to view different measurement data.
-
Press to start the next lap (press for a moment).
-
Press to manual pause the Blade when you stop moving. But Blade has an automatic Start/Stop function , no manual operation is required for a short pause.
NOTE : After manual pause, must press to started manually, then you can start riding. -
Long press the to save your ride; Then enter the history view; Long press the to exit the history view.
For detailed explanations of the history view, please refer to “History” (page
- Importing ride data to a smartphone (MEILAN app). You can view the ride data on smartphone and share it to Strava and Trainingpeaks.
- You can import measurement results by connecting the Blade to a smartphone (MEILAN app). For detailed explanations of the ride data, please refer to “History- Upload Your Ride to MEILAN app ” (page 8)
Changing settings
-
Change the setting from the Blade: It needs to be re-set.
For detailed explanations of the setting up with Blade please refer to “Setting up with BLADE” (page 3) -
Use smartphone (MEILAN app) to change settings:
Launch MEILAN app, tap “+ Add devices” to add Blade and the smartphone will connect with the Blade. Then follow the procedure below.
Changing the measurement unit (KM/H or MPH)
A. Tap ‘More’ > ‘Measurement’, you can see Metric or Imperial.
B. Select: Metric or Imperial, and Confirm. Refer to the Figure 01 to 03.
Inputing the initial settings for total distance
A. Tap “BLADE” to go to Blade setting menu.
B. Tap “ODO”, input the total distance. Refer to the Figure 04 to 06.
Adding a new sensor
A. Tap “BLADE” to go to Blade setting menu.
B. Tap “Sensor” → “Add sensor” to searching and add sensor. Refer to the
Figure 07 to 10.
Changing sensor tire circumference values
A. Tap “BLADE” to go to Blade setting menu.
B. Tap “Sensor” → “Triangle indicator area” of picture 13 to change tire
circumference and sensor rename. Refer to the Figure 11 to 14.
History
Viewing on Blade
- Long press to enter or exit history view.
- Press to check different measurement data in the record you are viewing.
- Press to check the segment data (lap) in the record you are viewing.
- Press to scroll to the next one.
Viewing with a smartphone (MEILAN app)
- Launch MEILAN app.
- Tap “More”to view ‘Total’, ‘7 days’, ’30 days’, ‘1 year’, you can choose to view any ride records.
- Tap “Datasheets of 7 days”, you can view the ride records of the last 7 days.
Deleting Your Riding Data
- Long press to enter or exit history view.
- Press to scroll to the record view you want to delete.
- Then press the SETTING button on the back of Blade to delete. Just delete this record.
- If you want to delete all the records at once, please restore the factory settings.
Uploading Your Ride to MEILAN app
Launch MEILAN app, Turn on the Blade, it will automatically connect with the app. Then the data of you save on Blade is automatically uploaded and imported into the MEILAN app.
Packing List
Standard Accessories
Optional Accessories
Appendix
Tire Circumference
Tire circumference can be determined by either of the following two methods:
If you use imperial units, please pay attention to the conversion to inches.
Measure the actual tire circumference (L)
After ensuring that the tire pressure is appropriate, sit on your bike, roll
it forward so that the tire makes one full revolution (use the valve or other
marking as a reference), and measure the distance traveled on the road.
Tire circumference reference table
- Generally, the tire size or ETRTO code is indicated on the side of the tire.
ETRTO Wheel Size L(mm)
47-203| 12×1.75| 935
54-203| 12×1.95| 940
40-254| 14×1.50| 1020
47-254| 14×1.75| 1055
40-305| 16×1.50| 1185
47-305| 16×1.75| 1195
54-305| 16×2.00| 1245
28-349| 16×1-1/8| 1290
37-349| 16×1-3/8| 1300
32-369| 17×1-1/4(369)| 1340
40-355| 18×1.5| 1340
47-355| 18×1.75| 1350
32-406| 20×1.25| 1450
35-406| 20×1.35| 1460
40-406| 20×1.50| 1490
47-406| 20×1.75| 1515
50-406| 20×1.95| 1565
28-451| 20×1-1/8| 1545
37-451| 12×1-3/8| 1615
37-501| 22×1-3/8| 1770
40-501| 22×1-1/2| 1785
47-507| 24×1.75| 1890
50-507| 24×2.00| 1925
54-507| 24×2.125| 1965
25-520| 24×1(520)| 1753
| 24×3/4 Tubrlar| 1785
28-540| 24×1-1/8| 1795
32-540| 24×1-1/4| 1905
25-559| 26×1(559)| 1913
32-559| 26×1.25| 1950
37-559| 26×1.40| 2005
40-559| 26×1.50| 2010
47-559| 26×1.75| 2023
50-559| 26×1.95| 2050
54-559| 26×2.10| 2068
57-559| 26×2.125| 2070
58-559| 26×2.35| 2083
75-559| 26×3.00| 2170
ETRTO Wheel Size L(mm)
28-590| 26×1-1/8| 1970
37-590| 26×1-3/8| 2068
37-584| 26×1-1/2| 2100
| 650C Tubular 26×7/8| 1920
20-571| 650x20C| 1938
23-571| 650x23C| 1944
25-571| 650x25C
26×1(571)
| 1952
40-590| 650x38A| 2125
40-584| 650x38B| 2105
25-630| 27×1(630)| 2145
28-630| 27×1-1/8| 2155
32-630| 27×1-1/4| 2161
37-630| 27×1-3/8| 2169
40-584| 27.5×1.50| 2079
50-584| 27.5×1.95| 2090
54-484| 27.5×2.10| 2148
57-584| 27.5×2.25| 2182
18-622| 700x18C| 2070
19-622| 700x19C| 2080
20-622| 700x20C| 2086
23-622| 700x23C| 2096
25-622| 700x25C| 2105
28-622| 700x28C| 2136
30-622| 700x30C| 2146
32-622| 700x32C| 2155
| 700C Tubular| 2130
35-622| 700x35C| 2168
38-622| 700x38C| 2180
40-622| 700x40C| 2200
42-622| 700x42C| 2224
44-622| 700x44C| 2235
45-622| 700x45C| 2242
47-622| 700x47C| 2268
54-622| 29×2.1| 2288
56-622| 29×2.2| 2298
60-622| 29×2.3| 2326
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>