Shenzhen Meilan Technology CUTEEYE Bicycle Intelligent Taillight User Guide
- June 6, 2024
- Shenzhen Meilan Technology
Table of Contents
CUTE EYE Quick User Guide
Remote control mounted on the handlebar
Place tho CUTE EYE near tho top of tho Seatpost
Remove light body
Sightly press the fixed buckle and take out the light body
Secure on saddle rail
Buttons and functions
Short press: the laser light is always on/flashing/off.
Short press: light mode switch.
Long press: the tail light turns off.if there is no movement for 30
minutes, the tail light will enter the automatic shutdown state. You must
long-press to turn it on again
Short press : turn left.
Short press again: stop left turn signal.
Short press : turn right.
Short press again: stop right turn signal.
Short press : change the light mode.
Long press: turn on.
Long press again: turn off.
How to pair?
Remote control and tail light pairing
Turn off Cute Eye. Long press and hold until two yellow lights appear on the
right (Cute Eye is in the pairing mode). Short press any button on the remote
control and start painting. Cute Eye is successfully paired when it appears in
full yellow light mode.
Enable and disable automatic brake warning function
Switch automatic brake warning functions in the thawing state. Press and hold
the button for ‘I second, if four red lights in the middle flash irregularly,
it means the automatic brake function has been enabled; if four red lights in
the middle stay on, it means automatic brake function has been disabled.
Cute Eye uses a built-in chip to intelligently detect the occurrence of
braking behavior. Due to the diversity of road conditions and personal usage
habits. 100% accurate detection is currently not available If it affects your
user experience, please turn off this function
Reminder: This product uses lasers that comply with the American UL
standard in the global area. Laws and regulations may apply to some European
countries, the products sold by sellers may not contain later light function
Please pay attention to the notification
Specifications
- Battery type: rechargeable 18650 lithium battery, 2500 mAh
- Wireless transmission method: Bluetooth BLE
- Working frequency band: 2.46 HZ
- Ambient temperature: -10 to 40 t
- Waterproof level: I PX6
Charging
Replacement of remote control battery
Please replace the battery in the remote control when the LED no longer lights
up. The remote control is powered by a CR2032 button battery Please use a
standard brand battery. The battery has positive and negative polarity. Please
install it in the correct way.
Unlock the buckle of the plastic shell as shown in the figure down below. Take
out the circuit board and the battery to place the new one
Safety statement and warranty
- Do not throw used batteries into water or an uncontrolled natural environment. Do not place this product on rue or in an extremely high-temperature environment.
- When the product is not used continuously for six months, please charge it at least once before using it.
- This product is suitable to use from light to moderate rain. Do not use the product in the heavy rain or immerse it in water.
- The automatic turning function provided by this product is only an auxiliary reminder function_ Due to temporary change of the road or uncontrollable factors in the product itself, the turning indication may violate your actual driving direction. Please do not take Cute Eye’s turning indication as the main safety guarantee. Consumers shall bear the personal and property safety losses caused thereby.
- This product was developed in accordance with the EN300328V1 .9.1 standard. Please observe the local laws and regulations when using it in different countries and regions.
- The product is guaranteed S one-year warranty for non-human damage (from the date of sale), and the accessories are not covered by the warranty. You can contact the after-sales service through MILAN global distributors or by writing to MILAN.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>