DATALOGIC BC9600 PowerScan BT Base Chargers Instruction Manual

DATALOGIC BC9600 PowerScan BT Base Chargers

Product Information

Specifications

• Manufacturer: Datalogic S.r.l.
• Model: PM9600/PM9600DPX, PM9600AR
• Base Charger Types: BC9600 & BC9620
• Reader Type: Industrial Cordless Handheld Area Imager Bar Code Reader

Disclaimer
Datalogic has made every effort to ensure that the information provided in this manual is complete and accurate. However, Datalogic shall not be held liable for any technical or editorial errors or omissions contained herein. Additionally, Datalogic is not responsible for any incidental or consequential damages that may result from the use of this material. Please note that Datalogic reserves the right to change specifications without prior notice.

Trademarks
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. PowerScan is a trademark of Datalogic S.p.A. and/or its affiliates. All other trademarks and brands mentioned are the property of their respective owners.

Patents
This product is covered by various utility patents. For a complete list of patents, please visit www.patents.datalogic.com.

Product Usage Instructions

Caution
Please adhere to the following precautions:

• Do not insert or apply any objects such as coins, paper clips, stickers, or similar items between the sides of the boot of the reader and the corresponding inner part of the base charger.
• Do not apply any stickers on the sides of the boot of the reader.
• Refer to the provided image for the affected areas indicated by red arrows.

Regulatory Addendum
This document serves as an addendum to the Quick Start Guide (QSG) for this product. Please refer to the QSG for additional product information.

Regulatory Information
All models are designed to comply with rules and regulations in the locations where they are sold. The products will be appropriately labeled as required. Any changes or modifications to the equipment that are not expressly approved by Datalogic may void the user’s authority to operate the equipment.

Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. The operation of this device is subject to the following conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any change or modification to the product that is not expressly approved by Datalogic may void the user’s authority to operate the device.

FAQ

• Q: What should I do if I encounter technical issues with the product?
  A: If you experience any technical issues with the product, please refer to the troubleshooting section of the user manual or contact our customer support for assistance.

• Q: Can I use the product in any country?
  A: The product is designed to comply with rules and regulations in the locations where it is sold. Please ensure that you are using the product in a country where it is compliant.

• Q: Are there any specific maintenance requirements for the product?
  A: Please refer to the maintenance section of the user manual for detailed instructions on how to properly maintain the product.

Datalogic S.r.l.

• Via S. Vitalino, 13
• 40012 Calderara di Reno (BO)
• Italy
• Tel. +39 051 3147011
• Fax +39 051 3147205

©2022-2023 Datalogic S.p.A. and/or its affiliates

• All rights reserved. Without limiting the rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a retrieval sys-tem, or transmitted in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates.
• Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser’s own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Electronic versions of this document may be downloaded from the Datalogic website ( www.datalogic.com ). If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the “Contact” page.

Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or conse-quential damages resulting from the use of this material. Datalogic reserves the right to change any specification at any time without prior notice.

Trademarks

• Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.
• PowerScan is a trademark of Datalogic S.p.A. and/or its affiliates, registered in the U.S. All other trademarks and brands are property their respective owners.

Patents

See www.patents.datalogic.com for patent list.

• PM9600/PM9600DPX
  This product is covered by one or more of the following patents:

  • Utility patents: EP1873886B1, EP2382502B1, EP2517148B1, EP2577559B1, EP2649555B1, EP2795534B1, EP3607487B1, US7948214, US8517273, US8743263, US8888003, US8915443, US9087251, US9430689, US9482793, US9569653, US9798948, US10025966, US10496858, US10817685, US10915719, US10915476, US11334735, ZL200780030808.2, ZL200880132595.9, ZL200980163411.X, ZL201080071124.9, ZL201180026461.0.

• PM9600AR

  • This product is covered by one or more of the following patents:
    Utility patents: EP1873886B1, EP2382502B1, EP2517148B1, EP2577559B1, EP2649555B1, EP2795534B1, EP3607487B1, EP3869384B1, US7948214, US8517273, US8743263, US8888003, US8915443, US9087251, US9430689, US9482793, US9569653, US9798948, US10025966, US10496858, US10817685, US10915719, US10915476, US11227173, US11334735, US11416697, ZL200780030808.2, ZL200880132595.9, ZL200980163411.X, ZL201080071124.9, ZL201180026461.0.

Model Number:

• PM9600/PM9600AR/PM9600DPX
• BC9600-433/BC9600-910
• BC9620 type 433/910/BT

CAUTION: Do not insert nor apply any objects such as coins, paper clips, stickers or similar between the sides of the boot of the reader and the corresponding inner part of the base charger. Do not apply any stickers on the sides of the boot of the reader. The red arrows in the image below indicate the affected areas.

REGULATORY ADDENDUM

Industrial Cordless Handheld Area Imager Bar Code Reader
©2022-2023 Datalogic S.p.A. and/or its affiliates • All rights reserved Without limiting the rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates • Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S. and the E.U.

This document is an addendum to the Quick Start Guide (QSG) for this product. See the QSG for additional product information.

REGULATORY INFORMATION

• All models are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
• Any changes or modifications to equipment, not expressly approved by Datalogic could void the user’s authority to operate the equipment.

Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Any change or modification to the product not expressly approved by Datalogic could void the user’s authority to operate the device.

FCC Class B Compliance Statement

• The user is cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
• This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio or television technician for help.

Base Charger BC9600-433/910 and BC9620 type 433/910/BT

FCC

CAUTION : Exposure to Radio Frequency Radiation
To comply with FCC RF exposure compliance requirements, for mobile configura- tions, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.

IC Canada Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
3. A separation distance of at least 20 cm must be maintained between the antenna of this device and all persons to comply with the safety require-ments for mobile RF exposure conditions in accordance with RSS-102 Issue 5.

Reader PowerScan PM9600

Canada Notice
RF Exposure Safety According to “RSS-102 Issue 5 (2015-03) – Radio Frequency Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands)”, paragraph “2.5.1 Exemption Limits for Routine Evaluation – SAR Evaluation”, the device operates below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance. The evaluation has been done at a distance of 5mm.

FCC
Radiofrequency Radiation Exposure Information:

• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 5mm between the radiator and your body.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Customs Union
The CU conformity certification has been achieved; this allows the Product to bear the Eurasian mark of conformity.

• Frequency Band Used:
  433,050-434,790 MHz; 902-928 MHz; 2400-2483,5 MHz

• Maximum output power:

  • < 10 dBm for 433MHz and 910MHz
  • < 20 dBm for Bluetooth

Power Supply
This device is intended to be connected to a UL Listed/CSA Certified computer which supplies power directly to the device or else be supplied by UL Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 10-30V mini-mum 1.5A.

Argentina Power Supply Statement

DEVICE LABELING

Sample labels are shown here to illustrate their location only. Please view the labels on your product for actual details, as they may vary from those depicted.

Scanner Regulatory Label

Base Regulatory Label

Aiming System

• The aiming system of this device meets the Class 2 requirements for laser safety. The laser information is located on the scanner label. The laser scanner conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN60825-1 at the date of manufacture.
• The laser light is visible to the human eye and is emitted from the out-put window.
• The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your terminal.

STANDARD LASER SAFETY REGULATIONS

• This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1 at the date of manufacture.
• For installation, use and maintenance, it is not necessary to open the device.
• WARNING: Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous visible laser light.
• The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid allowing the laser beam to hit the eye of an observer, even through reflective surfaces such as mirrors, etc.

WEEE STATEMENT

Waste Electrical and Electronic Equipment (WEEE) Statement

For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.datalogic.com .

CHINA ROHS TABLE OF RESTRICTED ELEMENTS (SCANNER)

PART| | | | | | |
---|---|---|---|---|---|---|---
Lead (Pb)| Mercury (Hg)| Cadmium

(Cd)

| Hexavalent

Chromium (Cr(VI)

| Polybrominated biphenyls

(PBB)

| Polybrominated diphenyl

ethers (PBDE)

Printed Circuit

Board Assy

| | X| O| O| O| O| O
Assembly, Module| | X| O| O| O| O| O
Assembly Optics Block| | X| O| O| O| O| O

CHINA ROHS TABLE OF RESTRICTED ELEMENTS (BASE)

PART| | | | | | |
---|---|---|---|---|---|---|---
Lead (Pb)| Mercury (Hg)| Cadmium

(Cd)

| Hexavalent

Chromium (Cr(VI)

| Polybrominated biphenyls

(PBB)

| Polybrominated diphenyl

ethers (PBDE)

Printed Circuit Board Assy| |

X

|

O

|

O

|

O

|

O

|

O

Assembly module| |

X

|

O

|

O

|

O

|

O

|

O

EFUP determined by “Look-up Method” (scanner).

Wireless Charging system

• WPT frequency: 120kHz-150kHz
• Max Power @3m: 18,3 dBuA/m

European Declaration of Compliance
Hereby, Datalogic S.r.l. declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.datalogic.com . Select the Support & Service > Downloads > Product Certifications link where you can search for your specific product certification.

UKCA Declaration of Conformity
Hereby, Datalogic S.r.l. declares that the full text of the UKCA Declaration of Conformity is available at: www.datalogic.com . Select the Sup-port & Service >Downloads > Product Certifications link where you can search for your specific product certification.

References

• Datalogic | Automatic Data Capture and Industrial Automation - Datalogic
• Patents - Datalogic

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>