Hipopller ST27BR Double 2 Door Commercial Refrigerators Instruction Manual
- June 15, 2024
- Hipopller
Table of Contents
Hipopller ST27BR Double 2 Door Commercial Refrigerators Instruction Manual
Dear Customer,
Congratulations on your purchase of this product. Like all our products, this product has also been developed on the basis of the latest technology and produced using reliable and modern electrical components.
Please take a few minutes before starting operation of the appliance and read the following operating instructions. Save this manual for further reference.
Many thanks.
Safety Tips
- The appliance is intended for commercial use or similar use (etc. to be used by a layman in shops).
- DO NOT use the appliance outside.
- DO NOT attempt to service the item yourself.
- DO NOT use damaged appliances. If you are in any doubt, consult service agent.
- DO NOT use electrical appliances inside the appliance (e.g. heaters, ice-cream makers etc.), unless they are of the type recommended by the manufacturer. 6. Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
- DO NOT use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
- DO NOT damage the refrigerant circuit.
- DO NOT stand or support yourself on the base, drawers or the door.
- DO NOT allow oil or fat to come into contact with the plastic components or door seal. Clean immediately if contact occurs.
- DO NOT place combustible, explosive or volatile articles, corrosive acids or alkalis or liquids in the appliance.
- DO NOT use this appliance to store medical supplies.
- DO NOT use jet/pressure washers to clean the appliance.
- DO NOT allow children to play with the packaging, and destroy plastic bags safely.
- Bottles that contain a high percentage of alcohol must be sealed and placed vertically in the refrigerator.
- Always carry, store and handle the appliance in a vertical orientation and move by holding the base of the appliance.
- Always switch off and disconnect the power supply to the unit before cleaning.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a hazard.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- For indoor used only. Not suitable for installation in an area where a water jet could be used. Must not be cleaned by a water jet.
- To guarantee safe operation, ensure that the appliance is set up and connected as described in the instruction manual.
- Any repairs and work on the appliance should only be carried out by the customer service department.
- The key to the fridge/freezer should be kept out of the reach of children and users.
Important Safety Instruction
-
DANGER – Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.
-
CAUTION – Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult Repair Manual/Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed.
-
CAUTION – Risk Of Fire Or Explosion. Dispose Of Properly In Accordance With Federal Or Local Regulations. Flammable Refrigerant Used.
-
Caution – Risk of Fire or Explosion due to Flammable Refrigerant Used. Follow Handling Instructions Carefully in Compliance with Local Government Regulations.
-
DANGER – Risk Of Fire or Explosion. Flammable Refrigerant Used. Do Not Use Mechanical Devices To Defrost Refrigerator. Do Not Puncture Refrigerant Tubing。
-
CAUTION – Flammable refrigerant used! When handing, moving and use of the refrigerator, make sure to avoid either damaging the refrigerant tubing, or increasing the risk of a leak.
-
Component parts shall be replaced with like components and that servicing shall be done by factory authorized service personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper service.
-
The appliance is not for the display of potentially hazardous foods.
For model ST27BRG, ST27BRGC, ST27BFG, ST27BFGC, ST54BRG, ST54BRGC, ST54BFG, ST54BFGC: -
The equipment is intended for use in an area where the enviromental conditions are controlled and maintained so that the ambient temperature typically does not exceed 86°F(30°C).
Intended Use
Only use this appliance for cooling and storage of food and beverage for commercial purposes.
Parts
ST54BR
- Front Panel
- Thermostat
- Lamp
- Lock
- Lamp of Swich
- Door
- Gasket
- Shelf Support
- Shelf Guide
- Shelf
- Feet
- Power
ST54BF
- Front Panel
- Thermostat
- Lamp
- Lock
- Lamp of Swich
- Door
- Gasket
- Shelf Support
- Shelf Guide
- Shelf
- Feet
- Power
ST27BR
- Front Panel
- Thermostat
- Lamp
- Lock
- Lamp of Swich
- Door
- Gasket
- Shelf Support
- Shelf Guide
- Shelf
- Feet
- Power
ST27BF
- Front Panel
- Thermostat
- Lamp
- Lock
- Lamp of Swich
- Door
- Gasket
- Shelf Support
- Shelf Guide
- Shelf
- Feet
- Power
ST27BRG\27BFG
- Front Panel
- Thermostat
- Power
- Lock
- Lamp of Swich
- Light
- Door
- Gasket
- Shelf Support
- Shelf Guide
- Shelf
- Feet
ST54BRG\54BFG
- Front Panel
- Thermostat
- Power
- Lock
- Lamp of Swich
- Light
- Door
- Gasket
- Shelf Support
- Shelf Guide
- Shelf
- Feet
ST27BRGC/27BFGC
- advertising lampbox
- Glass Door
- Gasket
- Lamp
- Shelf
- Shelf Support
- Shelf Guide
- Thermostat
- Lamp of Swith
- Control Panel
- Feet
- Lock
- Power
ST54BRGC/54BFGC
- advertising lampbox
- Glass Door
- Gasket.
- Lamp
- Shelf
- Shelf Support
- Shelf Guide
- Thermostat
- Lamp of Swith
- Control Panel
- Feet
- Lock
- Power
Location and Installation
The cabinet should be placed in a room that is dry and sufficiently
ventilated. To operate efficiently it should not be positio ned in direct
sunlight or near warm appliances. Please note that optimal cabinet performance
is obtained at an ambient temperature between +16 °C and +35 °C,
Freezer, Refrigerator: By placing the cabinet in an environment with high air
humidity, it may be necessary to acquire extra equipment for evaporation of
the drip water in the pan near the compressor.
The cabinet can be installed freestanding against a wall.
Important
The cabinet must have sufficient ventilation and free air circulation beneath,
above and behind the cabinet. The legs under the cabinet will help ensure
sufficient air space.
-
Remove the appliance from the packaging. Make sure that all protective plastic film and coatings are thoroughly removed from all
surfaces. To prevent injury or damage to the unit, we recommend that the appliance should be unpacked and set up by two people.
The appliance should be placed on a solid level floor to reduce noise and vibration. Level the appliance by adjusting the screw feet. Check that the power supply and voltage used comply with the details on the rating plate. The plug must be accessible after installation Correctly connect and disconnect the plug. When inserting ensure the plug is fully engaged. When unplugging do so by holding the body of the plug. Never pull the supply cord directly. -
If the appliance is to be shut down for long period, switch it off and disconnect the plug from socket outlet. Clean the appliance and leave the door open to prevent odour.
-
Important! For your personal safety, this appliance must be properly grounded (earthed). This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be inserted into an outlet that is properly grounded and installed. Consult a qualified electrician or servicecenter if you do not completely understand the grounding instructions. If doubt exits as to whether the appliance is properly grounded, have a qualified electrician check the circuit to make sure the outlet is properly grounded.
-
If the cable does not reach the nearest socket, either rearrange your store layout or ask a qualified electrician to fix a new socket.
-
If power is cut off, wait for at least 3 minutes before restarting the appliance to avoid damaging the compressor.
Note: If the unit has not been stored or moved in an upright position,
let it stand upright for approximately 12 hours before operation.
Note: Before using the appliance for the first time, clean the shelves
and interior with soapy water.
Power Requirements
The cabinet is intended for connection to an alternating current. The connection voltage (V) and frequency (Hz) are shown on the nameplate in the cabinet. The power connection is made using a three-pin plug to a wall socket. Any requirement for earthing from the local power supply must be met. The cabinet plug and wall socket should then give a correct earthing. If you are in doubt, contact your local supplier or authorized electrician.
Warning – This appliance must be earthed
The flexible cord fitted to this appliance has three cores for use with a 3-pin 13 Amp plug. If a B.B. 1363 (13 Amp) fused plug is used, it should be fitted with a 13 Amp fuse or a moulded right-angled Schuko plug. Note the plate with a hole in it between and above the two pins this connects to French and Belgian sockets, which have an earth pin that sticks out. Running in a slot coming from that plate is a continuation strip from the plate. Other European countries use a socket with a scrolled metal connector emerging from the side which mates with that strip. This ensures that the Schuko can be used in most mainland European countries.
Important
The wires in this mains lead are coloured in accordance with the following
code: Green-and-yellow: earth
Blue: neutral
Brown: live
The colours of the wires in the mains lead of this appliance might not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked “E”, marked by the earth symbol or coloured green- and-yellow. The wire, which is coloured blue, must be connected to the terminal, which is marked with the letter “N”, or coloured black. the wire which is coloured brown must be connected to the terminal which is marked with the letter “L” or coloured red.
Troubleshooting
If your Refrigerator, Freezer appliance develop a fault, please check the following table.
Fault | Probable Cause | Action |
---|---|---|
The appliance is not working | The unit is not switched on | Check that the unit |
is plugged in correctly and switched on
Plug and/or lead are damaged| Call our agent or qualified technician
Power supply| Check power supply
Internal wiring fault| Call our agent or qualified technician
The appliance turns on, but the temperature is too high/low| Too much ice on
the evaporator| Defrost the appliance
Condenser blocked with dust| Clean the condenser thoroughly
The door is not shut properly| Check that the door is shut and seals are not
damaged
Appliance is located near a heat source, or air flow to thecondenser is
blocked| Move the refrigerator to a more suitable location
Ambient temperature is too high| Increase ventilation or move appliance to a
cooler position
Unsuitable foodstuffs are being stored in the appliance| Remove any excessive
hot foodstuffs or blockages to the fan
Appliance is overloaded| Reduce the amount of food stored in the appliance
The appliance is leaking water (Refrigerator)| The appliance is not properly
levelled| Adjust the screw feet to level the appliance
The discharge outlet is blocked| Clear the discharge outlet
The water container is damaged| Call our agent or qualified technician
The appliance is unusually loud| Loose nut/ screw| Check and tighten all nuts
and screws
The appliance has not been installed in a level or stable position| Check
installation position and change if necessary
Disposal
If the cabinet is no longer of use and you wish to dispose of it, please do so in an environmentally correct way. There may be special requirements conditions. You can obtain information on the disposal of refrigeration appliances from:
- Your supplier
- Government authorities (The local council, Ministry of the Environment, etc.)
This equipment is intended for the storage and display of packaged products only
Circuit Diagram
Technical Data
model| supply
Voltage
(V/Hz)| Rated current
(A)| Temp. Range (°F )| Capacity| Dimension (WDH) (in)| Weight
(lb)
---|---|---|---|---|---|---
ST27BR| 115/60| 3.5| 34°F —41°F| 21| 27×32.183.1| 258
ST27BF| 115/60| 5| -10°F —10°F| 21| 27×32.183.1| 269
ST54BR| 115/60| 4.6| 34°F —41°F| 46| 54.1×32.183.1| 373
ST54BF| 115/60| 7.1| -10°F —10°F| 46| 54.1×32.183.1| 395
ST27BRG| 115/60| 3.5| 34°F —41°F| 21| 27×32.9×83.1| 267
ST27BFG| 115/60| 5| -10°F —10°F| 21| 27×32.9×83.1| 278
ST54BRG| 115/60| 4.6| 34°F —41°F| 46| 54.1×32.983.1| 412
ST54BFG| 115/60| 7.1| -10°F —10°F| 46| 54.1×32.983.1| 434
ST27BRGC| 115/60| 3.5| 34°F —41°F| 21| 27×32.9×83.1| 258
ST27BFGC| 115/60| 5| -10°F —10°F| 21| 27×32.9×83.1| 269
ST54BRGC| 115/60| 4.6| 34°F —41°F| 46| 54.1×32.983.1| 373
ST54BFGC| 115/60| 7.1| -10°F —10°F| 46| 54.1×32.983.1| 395
Environmental Protection
Discarded electric appliances are recyclable and should not be discarded in
the domestic waste! Please actively support us in conserving resources and
protecting the environment by returning this appliance to the collection
centres (if available).
Claims must be submitted immediately after their determination.
The right to guarantee claims expires upon any intervention of the purchaser or third parties. Damages caused by wrong treatment or operation, by false placement or storage, improper connection or installation, as well as force or other external influences are not covered by this guarantee. We recommend careful reading of the operating instructions as it contains important information.
The purchaser must prove the right to guarantee claims by presentation of the purchase receipt.
Note:
- In case this product does not function correctly, please firstly check if there are other reasons, e.g. interruption of the power supply, or incorrect handling are the cause.
- Please note that the following documents need to be submitted together with your faulty product:
- Purchase receipt
- Model description/Type/Brand
- Describe the fault and problem as detailed as possible.
In the case of a claim for guarantee or defects, please contact the seller personally.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>