EASYLINE DMBPDF Milkshake Mixer User Manual

EASYLINE DMBPDF Milkshake Mixer User Manual

Safety measures

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.
SAVE THIS INSTRUCTION.

Please read and understand this entire manual before attempting to assemble, operate or install the product. This manual contains important information about the assembly, operation and maintenance. General safety information is presented in these first few pages. Please keep this manual for future reference and to educate new users of this product.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic safety precautions should always be followed, otherwise, the potential risk of fire, electric shock and/or injury will be occurred.

When using electrical appliances, basic precautions should always be followed, including the following:

1. Read the instructions carefully.
2. To protect against risk of electrical shock, do not put the appliance in water or other liquid.
3. Adult supervision is quite necessary when the appliance is used by or near Children.
4. Unplug the power cord from the wall outlet when the appliance is not in use, before putting on or taking off parts, and before cleaning other than washing the container.
5. Never touch moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Call service at once for possible replacement, test and repair, electrical or mechanical adjustment.
7. Do not use outdoors.
8. Do not let the power cord hang over the edge of a table or counter, or get in contact with hot surfaces.
9. Keep hands and utensils out of the container during operation to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but only when the blender is not running
10. Please take off the cup after you make sure the blending blade is stopped entirely.

CAUTION

Blade is sharp. Handle carefully.

• Never try to remove blade while container is sitting on the motor base.
• Do not operate with loose, knicked or damaged blades.
• To reduce the risk of personal injury, never place blade assembly on motor base without blender container properly attached.
• Always operate with the lid in place.
• Display window area will scratch when contacted with a scouring pad or sharp object. Use a soft cloth to wipe the control panel area clean.

Technical information

Control Panel BL020

Power Switch

Located on the side of the Motor Base the ON/OFF switch controls the power to the machine. With the machine plugged in, switch the machine to ON to ready the machine for blending.

ON/OFF Switch

Pressing START/STOP once starts and runs the machine and turns the blades. Press the START/STOP button again to stop the machine and the blades.

PRE-SET Time buttons

These buttons, 8S, 12S, 60S, 90S are pre-programmed blending cycles designed for the most commonly made drinks. Depending on the viscosity of the drink you are creating, pressing one of the PRE-SET Time buttons will run the machine for a full cycle. The machine will stop by itself when the cycle is complete. A cycle varies in length, see the Instruction on next page for a complete description of the range of each PRE-SET button. Due to the difference of recipes, your results may vary.

DISPLAY WINDOW

This area show time to left and continue blending till all the number disappear.

HIGH/LOW PULSE button

These are pulse button, when you press H Pulse button, the machine will run with the highest speed, and when you press L Pulse button, the machine will run with 60% of the highest speed. Every press will keep 0.5 seconds running.

IMPACT Button

It is a button which have pre-set a common program. Once press the button, blender will automatically run in a circle: Ramp the blending speed to highest for 0.5 second, then stop for 1.5 seconds, then run again, ramp the blending speed to highest speed for 0.5 second again, then stop for 1.5 seconds again. The machine will run this circle for 10 times, then ramp to highest speed till the circle stop. The whole program last 30 seconds.

How to operate your blender using the PRE-SET Time buttons.

• 8S—(8 Seconds) Blends thin drinks with just juice and ice .
  This program will quickly ramp to a high blending speed for 8 seconds.

• 12S—(12 Seconds) Blends light coffee drinks.
  This button will ramp the blending speed to highest speed for 6 seconds, then ramp down to medium speed for 6 seconds.

• 30S—(30 Seconds) Creates a specialty drink with a thick viscosity.
  This button runs at a highest speed for 15 seconds, then ramp down to medium speed for 15 seconds.

• 60S—(60 seconds) Blend a regular smoothie for an extended cycle.
  This button runs for 30 seconds on a highest speed and then decrease in speed and runs on medium speed for 30 seconds.

Operation Instruction BL020

Place liquids and soft foods in the machines container first, solid items and ice last. Prepare food by cutting or breaking into 1-3 in.(2.54-7.62 cm) pieces. Frozen fruit, especially, should be as small as practical. Thawed or partially thawed fruit is recommended. We recommend Time button # 60S or # 90S for heavy-duty blending.
Set the container on the motor base by aligning it over the centering pad anchored to the base. (Motor must be completely stopped before positioning container).
Containers are not to be used for hard, dry materials. Avoid running the blender with container empty.
Always use a lid when blending. If blending hot ingredients. The lid must be securely in place.
Select desired programmed setting by pressing any of the Pre-Set Time button. The machine will begin immediately to cycle through the selected program, and turn off when the program is complete. Each button has a different pre- selected combination of speed and length for blending.
NOTE: If you detect a change in the sound of the machine or if a hard or foreign object comes into contact with the blades,  do not serve the drink, Inspect your blade assembly for loose, knicked or missing parts. If parts are loose ,missing or knicked replace with a new blade assembly.
Press ON/OFF button ,the machine will stop the blending cycle.
When the cycle is complete the blender stops, wait until blade comes to a complete stop before removing the lid and/or container from the motor base.
Remove the container, pour, garnish and serve the drink.

Control Panel BL008/BL020B/BL021

ON/OFF Switch

Up for ON; Down for OFF.

HIGH/LOW Pulse Switch

Up for High speed at 29000rpm; Down for Low speed at 16000rpm.
Pulse button can only used when the power switch is ON, The PULSE switch can be used to quickly refresh product in the container by depressing the switch and holding down as long as needed.

VARIABLE SPEED Dial

Allow user to select continuously variable motor speeds ranging from 16000rpm to 29000rpm.
PULSE switch is overrides the variable speed dial.

Operation Instruction BL008/BL020B/BL021

Fruit Ice

1. Material: Ice, Fruits, Water. They are all necessary.
2. Put the material into the container, cover the lid, when make thick drink, please plug the blending stick.
3. Set the variable button to a high speed(or the highest speed.)
4. Turn on SET Switch, if water is limited, please use the stick.
5. 3-5 seconds later, when the blending sound suddenly diminish, which means the material has been enough mashed, Stop the machine at once, to prevent the ice get into water with too much blending.
6. When mix the fruit, water and ice, the fruit juice will wrap the ice grain. It is the best Fruit Smoothie. Otherwise, only Ice and water, they won’t get the Smoothie effect. So Ice, Fruit, Water are all necessary.

Blending Fruit & Vegetable

1. Put fruit or vegetable and little water into the container.
2. Set medium speed or high speed.
3. Turn On SET switch, after 4-6 seconds blending, when the material roll smoothly , which means the material has been enough mashed, Stop the machine at once, to prevent over blending.

Operation Instruction DMB/DMB20

1. Place products to be processed in the cup.
2. Lock in the cup.
3. Press the button to start the appliance.
4. During use, continue to add food products through the hole in the cover
5. Press the button (A) to stop the appliance when finished.

Remark

On all units the built-in thermal sensor keeps track of how hot the motor gets and will automatically shut down the motor if the motor is overheating. User should remove the container and run the machine until cool. This takes about 2 minutes.

Special Note:

Please check your operation when the motor is overheated. If the machine run all the day or the material is too thick , it will easy to get overheated.

Caution

Never place any metallic materials inside the cup, such as: knives, forks, spoons, etc.
Please make sure to power off first before taking out the cup for cleaning in order to prevent danger.
Never use this device for cutting something in pieces or blending any solid food insoluble in water.
Please make sure the container is safely connected and fixed with the machine first
During operation because of the high speed of motor, make sure to hold the top cover with your hand.
During operation, please put correct materials in the cup to prevent from overflow while blending.
When you would like to pour out the food, please turn off the power source firstly, and take off the cup when the motor is NOT running.
Please pay attention all the time not to touch the Switch carelessly before or after the unit’s operation.

Cleaning

When maintaining or cleaning, please make sure the outlet is unplugged, and the switch is set to the “off” position.
Please clean the cup using a sponge or cloth carefully, and take it for airing.
Please clean the motor base and bearing by dry cloth (NEVER use water). In case you have to wipe please do it after cleaning by using a neutral lotion.

INFORMATION ON DISPOSAL AND RECYCLING OF THIS PRODUCT

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

WARRANTY CONDITIONS

• The warranty has duration of 12 months and is subject to the presentation of a copy of a suitable fiscal document or invoice proving the purchase date.
• The product is guaranteed against flaws and defects of the materials,manufacturing and assembly for 12 months from the date of the purchase invoice. The warranty consists in the replacement or repair of defective product components. It does not include the replacement of the product after breakdown repairs for any reason.
• Therefore the warranty is limited to the free replacement or repair of parts which, in the manufacturer’s opinion, malfunction. Consumable materials and tools are not included.
• Warranty services are rendered by the dealer where the product was purchased or, alternately, by the manufacturer, it being understood that the relevant transport will be at the customer’s full liability and expense.
• The warranty is invalidated if the product was tampered with or repaired by unauthorised personnel.
• This warranty substitutes and excludes any other warranty due by the dealer by law or contract and defines all the customer’s rights regarding purchased product defects and faults and/or quality deficiencies.
• Any legal controversy will be submitted to the manufacturer’s Court of residence.

References

• The domain name compra.la is for sale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>