Primo PSM-80E Spiral Mixer User Manual
- June 15, 2024
- PRIMO
Table of Contents
Primo PSM-80E Spiral Mixer
General Description
Thank you for using our PSM Spiral Mixer.
This machine used for paste mixing. It applies the advanced microcomputer
control system.
It uses manual and automatic control system. It has two speed controls, easy-
operating, safe and convenient. Paste can absorb large amount of water, and
the machine increases temperature slowly. This machine is ideal equipment for
hotel, cabaret, bakery and food-machining factory.
Main External Parts of Mixer
- Control plate: Rabbit stands for high speed, Turtle stands for low speed, Clock stands for timer, Hand stands for manual, and Arrowhead stands for reverse.
- Safety guard
- Bowl
- Cover
- Protective wheel
- Switch
- Body
- Support
- View Hole Cover
Operation Instruction
The machine has two controls: touch-panel control and manual-switch control
-
Touch-panel control
A. Put the materials into the bowl. Note that sufficient quantity is 55% of bowl volume with flour and water.
B. Automatic manner: switch on power supply; set 3-4 minutes at low speed, 7-8 minutes at high speed, and press “manual/automatic switch” to automatic state (“AUTO” light became light on the panel). Then press “ON” to turn on the machine, the machine will mix the flour at one time.
C. Manual manner: switch on power supply, press “manual/automatic switch” to manual state (“Manu” light became light on the panel). Press “quick/slow switch” at low speed, and press “ON” switch to start mixing at low speed, and to some extent, press “quick” mixing switch to complete mixing.
D. Take out paste after mixing. If turn on the face guard during mixing, then the machines will stop rotating. In this case, press “INCH” switch, then the machine can operate, and the paste can be taken out. -
Manual-switch control
The machine has manual switch at the left side, “1” is slow speed, and “2” is quick speed.
The switch can be turn to the required speed when using, and press the button beside the switch.
In the process of manual operation, the power supply of panel is turn off. If you want to use it again, then switch on the power supply again. -
The machine has slow or quick reversion function, and it can be used in blending the materials. When taking out the paste, reversion function can’t be used in case of breaking the paste.
-
At any times, if happens some accidents, press “Emergency Button” to stop the machine quickly to prevent any damage. The machine can be started again after finding out the reasons.
Notes
- The mixer must have good protective grounding.
- Don’t operate the mixer beyond the required quantity. When the quantity of water is below 55%, please reduce the flour.
- If use ice, please use shivers.
- Do not put the hand into the bowl when operating the mixer.
Maintenance
Take out the paste after mixing; wipe the inside of bowl, newel and pole with clean water and cloth. And move the unwanted materials above the bowl with clean cloth. Do not wash the below area of the machine.
- Wipe the panel with clean cloth with litter water; do not use toluene, gas .etc. volatile cleaner to clean the panel.
- Do not use nail or other hard things to press the button. Do not wash the panel and switch with water in case of electric shock.
- Make sure the machine works in a stable position, if it has some shakes, then adjust the adjustable foot to make the machine in stable.
- Put the butter into every butter hole in the bearing three months a time.
Easy trouble and solution
- The machine can’t start up:
- Check the power supply, whether lose phase or not.
- Check the fuse, if burnt, please replace it.
- Switch, emergency button and other buttons are in close or open.
- The machine can’t work normally, the belt often became flexible and slip, please adjust the belt.
Technical Data
| MODEL | PSM , 40 E | PSM-5 OE | P S M-60E |
|---|---|---|---|
| FLOUR CAPACITY | 1-20 kg {2.244 Ibs} | 1·25 Kg [2-2-55 lbs) | 1-37 Kg (2.2 82 |
lbs)
DOUGK CAPACITY| 1.6.32 Kg (3.5 71 lbs)| 1.S Kw (2.0) HP 135 RPM| 2.0 Kw (2.7
HP)120 RPM
1St SPEED| 1.6kw(2.1 HP) of 110 RPM| 1.5 Kw (2.0 HP) 135 RPM| 2.0 Kw (2.7 HP)
120 RPM
2th SPEED| 3.3 Kw (4.4 HP) 2.30 RPM| 3.0Kw (4.0 HP)270 RPM| 3.7 Kw (5.O HP)
24-0 RPM
BOWL MOTOR| 0HP, 23/11 RPM| 05.5 HP, 18 RPM| 0.55 HP, 17 RPM
VOLTAGE 208V/60/3| 7.1 AMPS| 6.8AMPS| 7.6AMPS
NET DIMENSIONS (WxDxH)| 24″x36.2″x48.4″| 24.4″x37.2″x50″| 28.4″ x 47.6″ x
56.2″
NET WEIGHT| 277 Kg (610 Ibs)| 325 Kg(717 Ibs)| 490 J(g (1080 Ibs)
SHIPPING DIMENSIONS(WxDxH)| 26.4″x40.6″x56″| 26.4″ x40.6″x56″|
29.9″.x49.2″x65.5″
SHIPPING WEIGHT| 330Kg(728IbS)| 378Kg(833 Ibs)| 570 Kg (1257 Ibs)
The “Reverse” function is not available for this model (PSM-40E)
MODEL| PSM , 8 0 E| PSM -120 E| P S
M- 1 60 (Not ETL listed
---|---|---|---
FLOUR CAPACJTY| 1.50Kg(2.2.110Ibs| 2.75 Kg (4.4-165 Ibs)| 2.100 Kg (4.4-220
Ibs)
DOUGH CAPACITY| 1.6-80 Kg (3.5 -176 Ibs)| 3.2 120 Kg (7.0- 265 Ibs)| 3.2- 160
kg (7.0 -353 Ibs)
1st SPE£D| 2.6 Kw (3.5 HP) 120 RPM| 3.7 Kw (5.0 HP) 100 RPM| 5.5 Kw {7.4 HP)
100 RPM
2th SPEED| 5.2 Kw (7.0 HP) 240 RPM| 7.5 Kw(10.0RPM) 200 RPM| 10 kw ( 13.0 PH)
200 RPM
BOWL MOTOR| 055.HP, 17 RPM| 0.75 HP, 16 RPM| 1.1 Hp.16 RPM
VOLTAGE 208V/60/3| 13.9AMPS| 15.2 AMPS| 20 AMPS
NET DIMENSIONS (WxDxH)| 28.4″x47.6″x56.3″‘| 30.9″ x48.8″x 59″| 37″x56x676″
NET WEIGHT| 512kg (1129 Ibs)| 670 Kg (1477 lbs)| 925 Kg (2039 Ibs)
SHIPPING DIMOOIONS (WxDxH)| 29.9″x 49.2″x65.5″| 33.9″54x 69″| 41″x62″x77″
SHIPPING WEIGHT| 590 kg (1300 Ibs)| 750 Kg (1653 lbs)| 1030 Kg (2271 Ibs)
CUSTOMER SUPPORT
5659 Royal mount Ave.
Montreal, QC H4P2P9 CANADA
Telephone: 514-737-9701
Toll Free Telephone:
1-888-275-4538
Fax: 514-342-3854
For service call 1-888-275-4538
3560 NW 56th St.
Fort Lauderdale, FL 33309 USA
Telephone: 786-600-4687
Toll Free Telephone:
1-844-218-8477
Fax: 786-661-4100
Email: service@mvpgroupcorp.com