KARCHER K2 Premium Power Control Instruction Manual
- June 15, 2024
- Karcher
Table of Contents
KARCHER K2 Premium Power Control
Product Information
Specifications
- Electric Connection:
- Voltage: 220-240V
- Phase: ~1
- Frequency: 50-60Hz
- Current Consumption: 6A
- Protection Class: II
- Water Connection:
- Maximum Inlet Pressure: 1.2MPa
- Maximum Inlet Temperature: 40°C
- Minimum Inlet Flow Rate: 8l/min
- Operating Pressure Range: 7.4-11.0MPa
- Typical Operating Weight: 5.0kg
- Dimensions:
- Length: 246mm
- Width: 280mm
- Height: 586mm
- Hand-Arm Vibration Value:
- Uncertainty K: m/s2
Product Usage Instructions
Safety Precautions
Before using the product, please read and follow these safety precautions:
- Make sure to read and understand the user manual before operating the product.
- Only use the product for its intended purpose as described in the manual.
- Do not modify or tamper with the product in any way.
- Always wear appropriate protective gear, such as safety goggles and gloves, when operating the product.
- Keep the product out of reach of children and pets.
- Do not point the high-pressure spray at people, animals, or electrical equipment.
- Always turn off the product and disconnect it from the power source before performing any maintenance or cleaning.
Assembly
To assemble the product, follow these steps:
- Attach the transport wheel to the product.
- Attach the handle grip to the product.
Initial Setup
Before using the product, make sure to connect it to a water supply. Follow
these steps:
- Connect the product to the water inlet using a suitable hose.
- Connect the other end of the hose to a water source.
Operating Instructions
To operate the product, follow these steps:
- Turn on the water supply.
- Press the power control button to select the desired pressure level (HARD, MEDIUM, SOFT, MIX).
- If using a cleaning detergent, follow the instructions provided with the detergent to mix it with water.
- Point the high-pressure spray at the surface to be cleaned and squeeze the trigger on the spray gun.
- To pause operation, lock the trigger on the spray gun and place it in the park position.
- To stop operation completely, turn off the water supply and release the trigger on the spray gun.
Transportation and Storage
When transporting or storing the product, follow these guidelines:
- Make sure the product is turned off and disconnected from the power source.
- Store the product in a dry and secure location.
- Protect the product from freezing temperatures by storing it in a frost-free area.
Maintenance
To maintain the product, follow these steps:
- Regularly clean the water inlet filter by removing it from the water connection and rinsing it under running water.
- Clean the detergent filter by removing it from the detergent container and rinsing it under running water.
FAQ
- Q: Can I use this product to clean my car?
- A: Yes, this product can be used to clean cars. Make sure to use the appropriate pressure level and follow the instructions provided.
- Q: Can I use hot water with this product?
- A: No, the maximum inlet temperature for this product is 40°C. Using higher temperatures may damage the product.
- Q: How often should I clean the filters?
- A: It is recommended to clean the water inlet filter and detergent filter regularly to ensure optimal performance. The frequency of cleaning depends on usage and water quality
General notes
Read these original operating instruc-tions and the enclosed safety
instruc-tions before using the device for the first time. Proceed accordingly.
Keep both books for future reference or for future own-ers.
KÄRCHER Home & Garden app
The KÄRCHER Home & Garden app contains:
- Installation and initial startup information
- Information about the areas of application
- Tips & Tricks
- FAQ with detailed troubleshooting
- Connection to the KÄRCHER Service Centre The app can be downloaded here:
Trademarks
- Google Play™ and Android™ are trademarks or registered trademarks of Google Inc.
- Apple® and App store® are trademarks or registered trademarks of Apple Inc.
Environmental protection
The packing materials can be recycled. Please dispose of packaging in accordance with the en-vironmental regulations. Electrical and electronic appliances contain valu-able, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential danger to human health and the envi- ronment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish. Cleaning work producing in oily wastewater, e.g. washing engines, washing undercarriages etc., may only be performed at washing stations with an oil separator. Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.
Notes on the content materials (REACH) Current information on content materials can be found at: www.kaercher.de/REACH
Intended use
Use the high-pressure cleaner in private households only. The high-pressure
cleaner is intended for cleaning ma-chines, vehicles, buildings, tools,
façades, terraces, garden machines etc. using a high-pressure water jet.
Accessories and spare parts
Only use original accessories and original spare parts. They ensure that
the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.
Scope of delivery
The scope of delivery for the appliance is shown on the packaging. Check the
contents for completeness when unpacking. If any accessories are missing or in
the event of any shipping damage, please notify your dealer.
Description of the device
The maximum amount of equipment is described in these operating instructions.
Depending on the model used, there are differences in the scope of delivery
(see packaging).
For the illustrations, refer to the graphics page Illustration A
- Transport wheel
- Storage for spray lance
- Storage / parking position for high-pressure gun
- Power Control spray lance dirt grinder for stubborn dirt, pressure level: HARD
- Click-Vario Power Power Control spray lance for the most common cleaning tasks, pressure levels: HARD / MEDIUM / SOFT / MIX
- Power Control high-pressure gun
- Clamp for connecting / disconnecting the high-pressure hose
- High-pressure gun lever
- High-pressure gun lock
- Trigger “0/OFF” / “I/ON”
- Mains connection with mains plug
- Storage hook for power cord
- Carrying handle
- Transport handle, telescoping
- Quick coupling for high-pressure hose
- Type plate
- High-pressure hose
- Detergent suction hose with detergent filter and cap
- Detergent tank
- Water connection with integrated sieve
- Water connection coupling
- Garden hose with commonly available coupling
- Fabric reinforced
- Diameter of at least 1/2 inch (13 mm)
- Length at least 7.5 m
- Washing brush, suitable for working with detergents
- Foam nozzle for powerful detergent foam
- Detergent container * optional, ** additionally required
Safety devices
CAUTION
- Missing or modified safety devices
- Safety devices are provided for your own protection.
- Never modify or bypass safety devices.
Power switch
The power switch prevents unintentional operation of the device.
High-pressure gun lock
The lock locks the lever of the high-pressure gun and prevents the device from
starting unintentionally.
Auto-stop function
If the lever of the high-pressure gun is released, the pressure switch turns
off the pump and the high-pressure jet stops. The pump switches on again when
the lever is pressed.
Symbols on the device
- Do not aim the high-pressure jet may at persons, animals, live electrical equipment or the device itself.
- Protect the device against frost. The device may not be directly connected to the public drinking water network
Assembly
For the illustrations, refer to the graphics page. Fit the supplied loose parts onto the device before starting up the device.
Fitting the wheels
- Fasten and secure the wheels to the device. Illustration B
Installing the handles
- Attach the transport handle.
- Attach the carrying handle.
Illustration C
Close the detergent tank
- Close the detergent tank with the cover.
Illustration D
Installing the water connection coupling
- Screw the water connection coupling onto the water connection on the device.
Illustration E
Initial startup
-
Place the device on a flat and level surface.
-
Insert the high-pressure hose into the quick coupling until it audibly latches into place.
Illustration F -
Press the clamp for the high-pressure hose together and pull out of the high-pressure gun.
Illustration G -
Insert the high-pressure hose into the high-pressure gun.
-
Press the clip in until it latches into place.
-
Check for a secure connection by pulling on the high-pressure hose.
-
Plug the mains plug into a mains socket.
Water supply
For the connection values, see the type plate or chapter Technical data.
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water Contamination in the water can damage the
pump and the accessories. KÄRCHER recommends using the KÄRCHER water filter
for protection(special accessory, order number 4.730-059).
Connection to the water line
ATTENTION
Hose coupling with Aquastop on the water connection of the device
Damage to the pump
Never use a hose coupling with Aquastop on the water connection of the device.
You can use an Aquastop coupling on the tap.
- Plug the garden hose onto the water connection coupling.
- Connect the garden hose to the water line.
- Open the water tap fully.
Illustration H
Operation
ATTENTION
Pump running dry
Damage to the device
If pressure does not build up in the device after 2 minutes then switch the
device off and proceed according to the instructions in chapter
Troubleshooting guide.
Power Control System
Note
The sensitivity of materials can vary greatly depending on age and condition.
The recommendations are therefore not binding.
High-pressure operation
ATTENTION
Damage to painted or sensitive surfaces Surfaces can be damaged when the jet
is too close to the surface or an unsuitable spray lance is used. Maintain a
minimum spray distance of 30 cm when cleaning painted surfaces. Do not clean
car tyres, paint or sensitive surfaces such as wood with the dirt grinder.
-
Insert a spray lance into the high-pressure gun and lock it by turning it 90°.
Illustration I -
Switch the device on (“I/ON”).
-
Unlock the lever of the high-pressure gun.
-
Press the lever of the high-pressure gun. The device switches on.
Operation with a washing brush
ATTENTION
Paint damage
- Damage to surfaces through a dirty brush
- Ensure that the washing brush is free from dirt or other particles before using it.
Note
The device operates at low pressure when using washing brushes. This means
that detergent can be mixed with the water.
- Insert the washing brush into the high-pressure gun and turn by 90° to fasten it.
Operation with detergent
DANGER
Failure to adhere to the safety data sheet.
Incorrect handling of the detergent can seriously damage your health Observe
the safety data sheet of the detergent manufacturer, in particular the
instructions on personal protective equipment.
Note
Detergent can only be mixed into the jet at low pressure.
Note
KÄRCHER detergents ensure fault-free operation. Ask us for a consultation,
request our catalogue or our detergent information sheets.
-
Fill the detergent solution into the detergent tank. Adhere to the dosage specifications on the detergent container.
Illustration J -
Close the detergent tank with the cover.
-
Latch the detergent tank in the device.
-
Use the Click-Vario Power spray lance.
-
Turn the spray lance to “MIX”. The detergent solution is mixed with the water jet during operation.
-
You can optionally use the foam nozzle.
-
Connect the foam nozzle to the detergent bottle.
Illustration K -
Insert the foam nozzle into the high-pressure gun and turn by 90° to fasten it.
-
Recommended cleaning method
- Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
- Rinse off the loosened dirt with the high-pressure jet.
After operation with detergent
- Flush the device with clear water for approx. 30 seconds.
Interrupting operation
- Release the lever of the high-pressure gun. The device switches off when the lever is released. The high pressure in the system is retained.
- Lock the lever of the high-pressure gun. Illustration L
- Place the high-pressure gun with the spray lance in the parking position.
- Switch the device off “0/OFF” during work breaks longer than 5 minutes.
Ending operation
CAUTION
Pressure in the system
Injuries from high-pressure water escaping uncontrollably. Only disconnect the
high-pressure hose from the highpressuregun or the device when the system is
fully depressurised.
- Release the lever of the high-pressure gun.
- Close the water tap.
- Press the lever of the high-pressure gun for 30 seconds. The pressure remaining in the system is discharged.
- Release the lever of the high-pressure gun.
- Lock the lever of the high-pressure gun.
- Disconnect the device from the water supply.
- Switch off the device “0/OFF”.
- Pull the mains plug out of the socket.
Transport
CAUTION
Failure to observe the weight.
Risk of injury and damage. Be aware of the weight of the device during
transportation.
Carrying the device
- Lift up the device by the carrying handle, and carry it.
Pulling the device
- Pull the transport handle out until it audibly latches into place.
- Pull the device via the transport handle.
Transporting the device in a vehicle
- Drain the detergent tank.
- Secure the device against slipping and tipping over.
Storage
CAUTION
Failure to observe the weight
Risk of injury and damage. Be aware of the weight of the device during
storage.
Storing the device
- Place the device on a level surface.
- Disconnect the spray lance from the high-pressure gun.
- Disconnect the high-pressure gun from the high-pressure hose.
- Disconnect the high-pressure hose from the device.
- Store the high-pressure hose on the device.
- Store the mains connection cable and accessories on the device.
Observe the additional notes before storing the device for a long period of time, see chapter Care and service.
Frost protection
ATTENTION: Danger of frost
Incompletely emptied devices can be destroyed by frost. Completely empty the
device and accessories. Protect the device from frost. The following
requirements must be satisfied:
- The device is disconnected from the water supply.
- The high-pressure hose is removed.
- Switch the device on “I/ON”.
- Wait for a maximum of 1 minute until no more water escapes from the high-pressure connection.
- Switch off the device.
- Store the device in a frost-protected room, together with all accessories.
Care and service
DANGER; Danger of electric shock
Injuries due to touching live parts
- Switch off the device.
- Remove the mains plug.
- The device is maintenance-free, i.e. you do not need to perform any maintenance work.
- Clean the sieve in the water connection
ATTENTION
- Damaged sieve in the water connection
- Damage to the device through contaminated water
- Check the sieve for damage before inserting it in the water connection.
If necessary, clean the sieve in the water connection.
-
Remove the water connection coupling.
-
Pull the sieve out using flat pliers.
-
Clean the sieve under running water.
Illustration M -
Insert the sieve into the water connection.
Clean the detergent filter
Clean the detergent filter before longer periods of storage.
- Pull the filter off the detergent suction hose.
- Clean the filter under running water.
Illustration N
Troubleshooting guide
Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.
DANGER
The danger of electric shock
- Injuries due to touching live parts
- Switch off the device.
- Remove the mains plug.
Device not running
- Press the lever of the high-pressure gun. The device switches on.
- Check that the voltage specified on the type plate corresponds to the voltage of the power source.
- Check the mains connection cable for damage.
- The device does not reach the required pressure
Water supply is too low
- Open the water tap fully.
- Check the water inlet for an adequate flow rate.
Sieve in the water connection is dirty
- Pull the sieve in the water connection out using flat pliers.
- Clean the sieve under running water.
Air is in the device
- Vent the device:
- Switch on the device without a connected spray lance for a maximum of 2 minutes.
- Press the high-pressure gun and wait until the water escaping from the high-pressure gun is free of air bubbles.
- Connect the spray lance.
Strong pressure fluctuations
- Clean the high-pressure nozzle:
- Use a needle to remove dirt from the nozzle drill.
- Rinse the high-pressure nozzle from the front with water.
- Check the water supply volume.
Device leaking
- The device leaks a small amount for technical reasons. If the leak is severe, request authorized Customer Service.
Detergent is not sucked in
- Use the Click-Vario Power spray lance and turn it to “MIX”.
- Clean the filter on the detergent suction hose.
- Check the detergent suction hose for kinks.
Warranty
The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorized customer service site. (See overleaf for the address)
Technical data
Electrical connection|
---|---
Voltage| V| 220-240
Phase| ~| 1
Frequency| Hz| 50-60
Current consumption| A| 6
Degree of protection| | IPX5
Protection class| **| II
Power protection (slow-blowing)| A| 10
Water connection| |
Feed pressure (max.)| MPa| 1,2
Input temperature (max.)| °C| 40
Input amount (min.)| l/min| 8
Device performance data| |
Operating pressure| MPa| 7,4
Max. permissible pressure| MPa| 11,0
Water flow rate| l/min| 5,5
Maximum flow rate| l/min| 6,0
Detergent flow rate| l/min| 0,3
High-pressure gun recoil force| N| 11
Dimensions and weights| |
Typical operating weight| kg| 5,0
Length| mm| 246
Width| mm| 280
Height| mm| 586
Determined values in acc. with EN 60335-2-79**
Hand-arm vibration value| m/s2| <2,5
Uncertainty K| m/s2| 0,3
Sound pressure level LpA| dB(A)| 74
Uncertainty K| dB(A)| 3
Subject to technical modifications.
Declaration of Conformity
We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.
Product : High-pressure cleaner
Type : 1.673-xxx
Currently applicable EU Directives
- 2000/14/EC
- 2014/30/EU
- 2006/42/EC (+2009/127/EC)
- 2011/65/EU
Harmonized standards used
- EN 50581
- EN 55014-1: 2017
- EN 55014-2: 2015
- EN 60335-1
- EN 60335-2-79
- EN 61000-3-2: 2014
- EN 61000-3-3: 2013
- EN 62233: 2008
Conformity evaluation procedure used 2000/14/EC: Appendix V Sound power level dB(A)
- Measured : 87
- Guaranteed : 90
The signatories act on behalf of and with the authority of the company management.
Documentation supervisor: S. Reiser Alfred Kärcher SE & Co. KG Alfred-Kärcher- Str. 28 – 40 71364 Winnenden (Germany) Ph.: +49 7195 14-0 Fax : +49 7195 14-2212 Winnenden, 2020/08/01
THANK YOU!
MERCI! DANKE! GRACIAS!
Rate your product and tell us your opinion.
www.kaercher.com/dealersearch ****
Documents / Resources
| K
RCHER K2 Premium Power
Control
[pdf] Instruction Manual
K2 Premium Power Control, K2, Premium Power Control, Power Control, Control
---|---
References
- Cher - Official Site
- Cleaning equipment and pressure washers | Kärcher International
- Dealer Search | Kärcher International
- Home and Garden Warranty Registration USA - Kärcher
- Reinigungsgeräte und Hochdruckreiniger | Kärcher
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>