melodySusie P Series Silvia Portable Nail Drill User Manual
- June 4, 2024
- melodysusie
Table of Contents
P Series
Silvia Nail Drill
User Manual
Thank you for choosing MelodySusie! Please read this user guide carefully and keep it in an accessible location so you may refer to it later.
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING.
To reduce the risk of burns, electrocution, fire, or injury to persons. Please
be sure to read the safety instruction as follow to avoid potential hazards
that could result in personal injuries or damage to the device.
Note: If the USB cable connects to the adapter, it is recommended to use
an adapter of 5V 2A. Please do not exceed 5V 2A, or the drill will burn out.
Check before Using
- Check the power supply cord before the first use and during the life of the device. Do not use this device if it has a damaged cord or it is not working properly or is damaged.
- Do not plug this device into a voltage system that is different from the voltage system specified on the device. Use with improper voltage will damage the device and VOID warranty.
- Please use the original cord only.
Note for Using
- Do not draw out the connecting wire during use or touch the cord with a wet hand to prevent electric leakage and shock or fire. Please turn the power off after use.
- Do not use the crooked or damaged nail drill bit or replace the bit when the power is on.
- Adjust the speed gradually, not abruptly. Please stop to use once the unusual movement and noise happen.
- Misuse, dropping or excessive force may cause device damage.
- Children under 18 years of age should not use this device without parental consent and supervision.
Maintenance Work
- Do not disassemble the device. Doing so could be dangerous and constitutes voiding warranty conditions.
- Do not keep the device in a place that is about or more than 50°C(in a metal box, car, or other places at high temperature). Keep the device dry and keep it away from the oil and grease.
- Store the device in a cool and dry place. Do not store it in a hot or humid environment.
- Keep electrical cord away from heated surfaces.
- Do not dispose of the device in heat or fire.
- Do not clean the device with harmful chemicals or detergents.
Note for Injury
- Having manicures done frequently can cause injuries to the nails as well.
- If you need to remove the gel polish of natural nails, try to use nail polish remover pads to avoid damage to the nail bed with the improper operation.
- Do not use the device if you have an open wound on your nail or hand.
- If you have any skin diseases, heat-sensitive, allergic reaction, onychomycosis, or any other disorder, you should consult your doctor and medical professional before using the device.
The operator shall be responsible for any consequences including product
damage or accidents if not strictly complies with the instructions.
If you require any technical support, contact us at
service@melodysusie.com SAVE THESE
INSTRUCTIONS
Six Drill Bits
How to Use
Step 1: Insert the drill bit firmly into the drill.
Step 2: Connect the nail drill power cord. The sliding switch on the
power cord turns the drill on and off.
Step 3: Move the switch up or down to choose the direction of spinning.
Slide the speed controller to accelerate or decelerate the rotation speed.
Step 4: After the polishing is finished, please turn off the machine by
returning the control switch to the middle position. 
Problem and Terms of Settlement
| Misoperation | Causing | Terms of settlement |
|---|---|---|
| Changing the nail drill bit when the power is on | 1. Motor burns out | |
| 2. Bearing damages (Loud Noise) | Turn off the power when changing the nail |
drill bit
When not in use, the speed is adjusted to the minimum, and the power is on|
Turn off the power when not in use
Long time, Large load work| 1. Motor burns out
2. Device lifespan shortens
3. Bearing damages (Loud Noise)| The continuous working time should not be
too long when the working condition is in heavy load. When the device is
overheating, it should be stopped immediately to make it return to normal
temperature
Misoperation| Causing| Terms of settlement
---|---|---
Insert into a mismatched power cord| 1. Motor burns out| According to
the device voltage requirements, insert the matching power cord
Put the power cord at random/ Pull the power cord| 1.
Power cord brokes
2. Poor connection| Do not pull the power cord
Replace the original cord randomly| 1. Motor bums out
2. Easy to cause a short circuit| Use the original
specification cord
Dust into device/ device drops to the ground or by other impacts|
1. Bearing damages (Loud Noise)
2. Motor gets hot
3. Rotational speed slows down| Clean dust, add the dust-proof
protection of the dustproof hood/Avoid device drops or other impacts
Insert the nail drill bit into the device incorrectly| 1.
Drill bit falls out
2. High vibration
3. Drill bit stocks| Insert the nail drill bit into the
device correctly/If the drill bit is stuck, please try to take it out hard
The size of the drill bit is not suitable| Can not insert the
drill bit into the device| Use a standard drill bit
Water into the device/Operate in wet or moist conditions/Use a wet cloth to
clean the device| 1. Motor burns out
2. Device lifespan shortens| Do not operate in wet or moist
conditions/Only a dry cloth is allowed for cleaning
Specifications
Input voltage range: 5V/2A Email: service©melodysusie.com Email:
service.uk@melodysusie.com Website:
www.melodysusie.com
Warranty and Customer Service
MelodySusie offers a 6-month limited warranty on quality-related issues.
Please apply for your extra 6-month warranty extension and download the user
manual in other languages by registering on
www.melodysusie.com if needed.
MAKE BEAUTY A NEW SMART
US: service@melodysusie.com
EU: service.uk@melodysusie.com
****http://www.melodysusie.com
Whipple Road, Union City, CA 94578
AMZLAB GmbH Laubenhof 23,
45326 Essen, Germany
THEM1S AR support ltd 85 Great Portland St, London, United Kingdom, W1 W 7 LT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>