COMMSCOPE TC-96275-IP Single Fiber Splice Cassette for Propel Panel User Guide

June 15, 2024
CommScope

COMMSCOPE TC-96275-IP Single Fiber Splice Cassette for Propel Panel

COMMSCOPE TC-96275-IP Single Fiber Splice Cassette for Propel Panel

Prepare cable for mass fiber splice cassette installation.

Refer to Table 1 for Feeder and Pigtail Lengths. “Feeder Initial Length” is the recommended length of fiber to bring into the cassette. “Feeder Cut Length” and “Pigtail Cut Length” is measured from the front of the cassette and is the recommended cut length for the initial splice. A maximum of (1) rework is allowed per splice.

Table 1: Pigtail and Feeder Lengths

Feeder Initial Length (in)| Feeder Cut Length (in)| Pigtail Cut Length (in)| Fiber Inside Propel Panel (in)
---|---|---|---
25(63.5 cm)| 17.25 (43.8 cm)| 20.5 (52 cm)| 21 (53.3 cm)

Prepare cable for mass fiber splice cassette
installation

Remove cassette cover

Using thumb & finger, disengage rear tab by lifting and pulling backward to remove the cover.
Remove cassette cover

Prepare to place feeder fiber in cassette

  • (a) Remove spool and splice holder from cassette, then remove and discard foam blocks.
    Prepare to place feeder fiber in cassette

  • (b) Unspool and extend pigtail fiber beyond front of cassette.
    Prepare to place feeder fiber in cassette

Install feeder fiber in splice cassette

  • (a) Insert plastic sleeve into mesh sleeve and secure using tape. Insert feeder fiber into sleeve.
    Install feeder fiber in splice cassette

  • (b) Secure feeder fiber using two cable ties.
    Install feeder fiber in splice cassette

  • (c) Snip off ends of cable ties close to head.
    Install feeder fiber in splice cassette

  • (d) Push the head downward until it is below the top of the cassette wall.
    Install feeder fiber in splice cassette

Measure and trim pigtail and feeder

Extend feeder fibers beyond the front of the cassette base, then measure and trim pigtail and feeder to specified cut length per Table 1.
Measure and trim pigtail and feeder

Install splice protectors on all fibers to be spliced

Use provided splice protectors. Splice protector length should be 45mm maximum.
Install splice protectors on all fibers to be spliced

Splice feeder and pigtail fibers

Strip, clean, and splice fibers following recommended method.

Preparing to load splice protectors

Locate “P” and “F” marking on spool. When loading splice protectors, ensure pigtail is exiting spool through the side with “P” marking and the feeder is exiting through the side with “F” marking.
Preparing to load splice protectors

Load splice protectors into splice holder

  • (a) Load splice protectors into splice holder
    Load splice protectors into splice holder

  • (b) Utilizing the spool fiber retainers, route pigtail fibers counterclockwise until feeder and pigtail fibers converge.
    Load splice protectors into splice holder

Route fibers into base

  • (a) Position spool to prepare for routing.
    Route fibers into base

  • (b) Route pigtail and feeder fibers counterclockwise starting along the outer walls and working towards the center of the cassette.
    Route fibers into base

  • (c) Line up the pegs on the cassette base with the mounting holes on the spool to finish routing.
    Route fibers into base

  • (d) Insert spool into base and ensure all fibers are under retaining fingers.
    Route fibers into base

Apply Cover

  • (a) Line the tabs on the cover with the slots near the front of the cassette base.
    Apply Cover

  • (b) Lay the cover flat on the base and ensure all the tabs on the side of the cover and bases are lined up. With one hand holding the cassette base, push cover forward with other hand to engage tabs. Double check the rear tab is also engaged to prevent the cover from sliding off.
    Apply Cover

Customer Support


PROPEL PRODUCT PAGE QR CODE

Product Information
http://www.commscope.com
Product Information
http://www.commscope.com/SupportCenter

© 2023, CommScope, Inc. All Rights Reserved.

http://www.commscope.com

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CommScope User Manuals

Related Manuals