rocstor Y10G002-B1 TrueReach HDMI Extender User Manual
- June 12, 2024
- rocstor
Table of Contents
rocstor Y10G002-B1 TrueReach HDMI Extender User Manual
Introduction
The Rocstor TrueReach HDMI extender, extends the transmit length of HDMI Visual/Audio up to 120m(394ft) with single network cable. Supports IR signal transmission, to control media playback of the signal source device at the display location.
Important Safety Instructions:
- Do not mix up the HDMI EXTENDER sender and HDMI EXTENDER receiver, and the IR blaster and IR receiver.
- Do not plug-in/out the cables ,when it is in use.
- Use DC SV power supply only
Package Contents
Note: above accessory content is regular package for a kit. If purchased HDMI extender TX or HDMI extender RX separately, the package contents would be different.
Installation Requirements
- HDMI source device (computer graphics card, DVD,PS3, HD monitoring equipment etc).
- HDMI display device like SDTV, HDTV, projector with HDMI port.
- Network cables: UTP/STP CatSe/6 network cables, which following the standard of IEEE-568B.
Transmission length: CATS 260ft (80m)/CATSE 328ft (100m)/CAT6 393ft (120m).
Panel Description
HOMIEXTENDER TX (Sender)
- Reset
- HDMI signal input
- IR signal output to connect with blaster extension cable
- Power input (DC5V)
- Power Light
- RI45 signal output
- Data transmission light
- Network link light
HDMIEXTENDER RX(Receiver)
- Reset
- HDMI signal output
- IR signal input to connect with IR receiver extension cable
- Power input ( DC5V )
- Power Light
- Ri4S signal intput
- Data transmission light
- Network link light
Installation Procedures
How to make a CatSe/6 network cable
Follow the stanard of IEEE-568B:
- Orange/white
- Orange
- Green/white
- Blue
- Blue/white
- Green
- grown/white
- Brown
Connections
Point to Point connection: Up to 3931t (120m) transmission distance over single CAT6 over single CAT6.
LAN Switch Cascade Connection: By using the LAN switch/router to realize unlimited extension.
One-to-many Connection: By using network router/switch , one sender to several receivers, realize extender & splitter function.
Note: It is recommended that Gigabit Ethernet switches be used in LAN. Fast Ethernet switches (100Mbps) and Gigabit Ethernet switches (1000Mbps) can not be mixed-used in cascade.
IR User Guide
- IR blaster extension cable should plug-in the IR-out port of TX (Sender) of HDMI extender, and the IR receiver extension cable should plug-in the IR-out port of the RX (Receiver) of HDMI extender.
- The emitter of IR blaster should as close as possible to the IR receiver of the signal source device.
- Using the IR remote controller of the signal source device towards the IR receiver (connected to the RX of HDMI extender), to remote control source media playback.
Specification
| Items | Specifications |
|---|---|
| HDMI Signal | HDML3 Compatible with HDCPL4 |
| Support resolutions. | 480/@60Hz, 480p@60HZ, ST6I@50HzZ, 576p@S0Hz, |
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
Network Cable| UTP/STP Cats/5e/6.
Transmission distance| Up to 120 meters transmission distance for 1080p 60tz
Full HD over single CATG
IR signal| Supports 20~60KHz IR devices
Working Temperature| 0 C – 60 C
Power Supply.| DC5V/1A
Power Consumption| TX 3.5W; RX:3W
protection| Lightning Protection, Surge Protection ESD protection
Dimensions| 56.8W) x94(0) x 23,7 H)mm *27C5
Weight| TX1459_RX: 1429
Color| Black
FAQ
Q: TV display “Waiting for connection” ?
A : Please check if the power supply of TX (Sender) and switcher (if used) iis
connected, and make sure connecting cable s firmly.
Q: TV display “Please check the TX input signal® ?
A – 1) please check if there is a HDMI signal input of TX. 2) Try to connect
the signal source directly to display device to see if there is singal output
from source device or change the signal source, HDMI wire and try again.
Q: Display not fluent, not stable?
A+ 1) Please check the cable length between the TX to switch, the switch 10
the RX and the connection between each level is within the required range. 2)
Click the reset button on the TX/RX front panel, reset and reconnect.
Contact Information
Corporate Headquarters
12979 Arroyo Ave
San Fernando, CA 91340 – USA
Oce: +1 818-727-7000
Fax: +1 818-875-0002
Email: info@Rocstor.com
Technical Support / RMA
Hours: 9:00 am – 5:00 pm PST
Mon – Fri (excluding holidays)
Sales Info
Hours: 8:00 am – 5:00 pm PST
Mon – Fri (excluding holidays)
Tell: +1 818-727-7000 (DOM/INTL)
Fax: +1 818-875-0002
Email: support@Rocstor.com
Tell: +1 818-727-7000 (DOM/INTL)
Fax: +1 818-875-0002
Email: support@Rocstor.com
Corporate, Government and Academic Customers
Our Corporate Sales Team’s goal is to help our U.S.A. and Canadian customers
nd a storage solution that best serves their needs. We will help you determine
your best purchasing options. For more information please contact the
appropriate department below or call us at +1
818-727-7000.
General sales information: sales@Rocstor.com
Corporate sales information:
corporate_sales@Rocstor.com
Educational sales information:
academic_sales@Rocstor.com
Federal, State & Local government sales information:
government_sales@Rocstor.com
Disclaimer
©2023 Rocstroge, Inc. Rocstor is registered trademark of Rocstorage, Inc. The terms HDMI, HDMI High-Defnition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.The product name and brand name may be registered trademark of related manufactures. ™ and ® may be omitted on the user manual. The pictures in this user manual are just for reference. We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>