REELCRAFT T-1460-4 Safe Reel Welding Cable Instruction Manual
- June 15, 2024
- REELCRAFT
Table of Contents
REELCRAFT T-1460-4 Safe Reel Welding Cable
Dimensions
IMPORTANT
Read this manual carefully before installing, operating or servicing this equipment.
SAFETY
- Injury and/or equipment damage may result if proper safety precautions are not observed.
- Ensure that only a qualified electrician installs/services this equipment.
- Ensure that power supply voltage does not exceed maximum voltage rating of reel.
- Ensure that reel is properly installed before connecting to power supply.
- Ensure that all electrical power is removed from reel before servicing.
- Check for frayed/broken wires before each use.
- Pull electrical cord from reel by grasping the electrical cord itself, not the work device.
- If an electrical malfunction should occur, remove power from reel immediately
- Ensure that reel, electrical cable, and equipment being serviced are properly grounded. Use an ohmmeter to check ground continuity.
- If reel ceases to unwind or rewind, remove power immediately. Do not pull or jerk on electrical cable!
- Treat and respect the cable reel as any other piece of machinery, observing all common safety practices.
WARNING: Even low voltage can cause irreparable damage or death! Exercise extreme caution while operating or servicing this equipment.
INSTALLATION INSTRUCTIONS
Inspection
Unpack and inspect reel for damage. Turn the reel by hand to check for smooth
operation. Check for completeness.
Mounting
Note: Ensure that only a qualified electrician installs/services this equipment.
- Four 1/2” diameter mounting holes are located at the base of the reel. Mount reel using four (customer supplied) bolts; tightening them securely to ensure a solid, rigid attachment. **(Figure 1)
**
Electrical
Note: Observe any applicable NEC, OSHA, and local electrical codes when installing this equipment.
- Attach a cable lug (customer supplied) to the end of the outlet cable.
- Mount lug to collector ring assembly using one 1/2-13 UNC bolt. (Figure 2)
| Item # | Description | # Req | T-1460-2 | T-1460-4 | T-1460-7 |
|---|---|---|---|---|---|
| 1 | Self Tapping Screw | 12 | S285-14 | S285-14 | S285-14 |
| 2 | Spool Cover | 1 | 261517 | 261517 | 261517 |
| 3 | Hex Cap Screw | 5 | S2-85 | S2-85 | S2-85 |
| 4 | Spool Half | 1 | 261546 | 261546 | 261546 |
| 5 | Hose Clamp | 1 | 261541-1 | 261541-1 | 261541-1 |
| 6 | Spool Half | 1 | 261547 | 261547 | 261547 |
| 7 | Spool Cover | 1 | 261518 | 261518 | 261518 |
| 8 | Shaft Key | 1 | 261516 | 261516 | 261516 |
| 9 | Hex Jam Nut | 1 | 261575 | 261575 | 261575 |
| 10 | Set Screw | — | None | None | None |
| 11 | Handle Post | 1 | 261515 | 261515 | 261515 |
| 12 | Handle | 1 | 261514 | 261514 | 261514 |
| 13 | Hex Jam Nut | 2 | S77-108 | S77-108 | S77-108 |
| 14 | Collector Ring Assembly | 1 | S600791 | S600791 | S600791 |
| 15 | Tensioning Nut | 1 | 261548 | 261548 | 261548 |
| 16 | Hub Assembly | 1 | S600752 | S600752 | S600752 |
| 17 | Main Shaft | 1 | 261545 | 261545 | 261545 |
| 18 | Base Assembly | 1 | 600746 | 600746 | 600746 |
| 19 | Cord Grip Assembly | 1 | 261555 | 261555 | 261555 |
| 20 | Lock Washer | 1 | S115-816 | S115-816 | S115-816 |
Customer Support
Reel craft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 /
260-248-8188 • Fax:
800-444-4587 /
260-248-2605
Customer Service: 855-634-9109 •
reelcraft@reelcraft.com •
www.reelcraft.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>