Standalone Access Control

User Manual

Introduction

The series of product is a new generation of multi-functional standalone access control. It adopts new ARM core 32-bit microprocessor design, which is powerful, stable and reliable. It contains reader mode and standalone access control mode etc.. It’s widely  applied to different occasions, such as office, residential communities, villa etc..

Features

Read 13.56MHz Mifare card and CPU card (Optional)
Keypad Characteristic| Operate by infrared remote
Output Way| Contain reader mode, the transmission format could be adjusted by users.
Access Way| Support multi access ways: Card, multi cards
Admin Card| Support admin card
User Capacity| 10,000 card users
Unlocking Signal| Relay NO/NC/COM output

Technical Specifications

Installation

• Remove the back cover from the keypad using the supplied special screw driver
• Drill 2 holes on the wall for the self-tapping screws and hole for the cable
• Put the supplied rubber bungs to into the two holes
• Fix the back cover firmly on the wall with 2 self-tapping screws
• Thread the cable through the cable hole
• Attach the keypad to the back cover. (as following illustration)

Wiring

Diagram

6.1 Common Power Supply

6.2 Special Power Supply

6.3 Reader Mode

Sound and Light Indication

Admin Menu

8.1 Standalone Mode Settings
Device Management

Enter programming| Menu| Operation steps| Description| Default value
---|---|---|---|---
Press
Admin code # (Default admin code  is “999999”)| 0| New admin code # new admin code #| Change admin code| 999999
1| 10001# Read card| Set admin add card|
10002# Read card | Set admin delete card|
2| 10001# | Delete admin add card|
10002# *| Delete admin delete card|
3| 11 #| Standalone access control mode| 11
12 #| Relay toggle mode
13 #| Reader mode
( 26-58 )#| Wiegand 26-58 bits output

Add and Delete Users

Enter programming| Menu| Operation steps| Description| Default value
---|---|---|---|---
Press
Admin code # (Default
admin code is “999999”)| 1| Read card … | Add card users continuously| , `…” means repeating the previous operation, Press key to exit.
Press 8 or 10 digits card number # … | Add card users by card number
Press ID number # Read card … | Add card users by specific ID number
Press ID number # Press 8 or 10 digits  card number #| Add card users by specific ID number and card number
Delete users
2| Read card… | Delete card users by reading card| “…” means repeating the previous operation, Press key to exit.
Press 8 or 10 digits card number #… | Delete card users by card number
Press ID number # … *| Delete users by ID number
0000#| Delete ALL users

Access Ways

Advanced Settings

Enter programming| Menu| Operation steps| Description| Default value
---|---|---|---|---
Press * Admin code #  (Default admin code is “999999”)| 4| (0-300) #| Door opening time range: 0-300S 0 equals to 50mS| 5
5| (0-99) #| Alarming time range: 0-99 min.| 0
7| Press ID number # press 8 or  10 digits card number # input card quantity

| Add conductive number card|

8| 0#| Normal working mode| 0
1#| The external alarm and built-in buzzer will work if wrong operations are over 5 times.
2#| The device will be locked out for 10 min if wrong operations are over 5 times.
3#| Disable light indicator| 4
4#| Enable light indicator
5#| Disable buzzer| 6
6#| Enable buzzer

8.2 Reader Mode Settings

Enter programming| Menu| Operation steps| Description| Default value
---|---|---|---|---
Press *
Admin code # (Default
admin code is
“999999”)| 0| New admin code # Repeat new admin code #| Change admin code| 999999
3| (13) #| Reader Mode|
(26-58) #| Wiegand 26-58 bits output| 26

Admin Operation

9.1 Add Users
Read admin add card | Read the 1″ usercard Read the 2“ usercard | Read admin add card
Note: The admin add card is used to add card continuously and quickly. When you read the admin add card at the first time, you will hear short “BEEP” sounds twice and  the indicator light turns orange, it means you have entered into add user programming, when you read the admin add card at the second time, you will hear long “BEEP” sound once and the indicator light turns red, it means you have exited the add user  programming.

9.2 Delete Users
Read admin delete card | Read the 1″ usercard Read the 2“ user card …. Read admin delete card
Note: The admin delete card is used to delete card continuously and quickly. When you read the admin delete card at the first time, you will hear short “BEEP” sounds twice and the indicator light turns orange, it means you have entered into delete user  programming, when you read the admin delete card at the second time, you will hear long “BEEP” sound once, the indicator light turns red, it means you have exited the delete user programming.

Other Operation

10.1 Remove Alarm
Read valid card or Press admin code#
Note: When the alarm is activated, users can remove the alarm by reading a valid card or pressing valid admin code.

10.2 Reset to Factory Default
Users can reset to the factory default when the admin code is forgotten, or the default settings have been modified disorderedly, operations as below:
Power off, press and hold the exit button continuously, power on, release the exit button until hearing beep sound twice, the admin code has been reset to 999999, factory default settings are successful.

Note: Registered user data won’t be deleted when reset to factory default.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>