SHB-4200 Box Camera Housing

Product Information

Specifications

(x2), Cushion Pad (x2), Bracket

Product Usage Instructions

1. Safety Instructions

• Do not install the unit in humid, dusty, or sooty locations.
  Doing so may cause fire or electric shock.

• If any unusual smells or smoke come from the unit, stop using
  the product. In such case, immediately disconnect the power source
  and contact the service center. Continued use in such a condition
  may cause fire or electric shock.

• If this product fails to operate normally, contact the nearest
  service center. Never disassemble or modify this product in any
  way. (HANWHA is not liable for problems caused by unauthorized
  modifications or attempted repair.)

• When cleaning, do not spray water directly onto parts of the
  product. Doing so may cause fire or electric shock.

• Do not expose the product to the direct airflow from an air
  conditioner. Otherwise, it may cause moisture condensation inside
  the clear Dome due to temperature difference between internal and
  external of the dome camera.

• If you install this product in a low-temp area such as inside a
  cold store, you must seal up the wiring pipe with silicon so that
  the external air cannot flow inside the housing. Vapor inside the
  product due to a difference between internal and external
  temperature.

2. Product Overview

This CAMERA-HOUSING is designed to install the outdoor CCTV
camera securely to protect it from external conditions.

3. Features

• Dustproof
• Sealed

4. Product Specifications

Model Name: SHB-4200H

Purpose: Outdoor Housing

Product Name: Camera Housing

Features: Dustproof, Sealed

Material: –

Use Condition: -35°C ~ +50°C

Weight: 1.1kg

Input Power: AC 24V

Dimension (Outside): 148mm(W) x 107mm(H) x 421mm(D)

Dimension (Inside): 84mm(W) x 78mm(H) x 260mm(D)

Color: Ivory

Accessories: Housing, Bracket

5. Exterior

No information provided.

6. Installation

1. Mount the camera inside the housing.

2. Connect the BNC connector to the cable and insert it to the
   cable gland from inside.

3. Insert the cable to the concord from outside and connect it to
   the BNC connector.

7. Installing the bracket and the cushion pad

Depending on the size of the camera, the location of the cushion
pads may vary.

FAQ (Frequently Asked Questions)

1. 1. Can I install this camera housing in a humid environment?

No, it is not recommended to install the unit in humid, dusty,
or sooty locations as it may cause fire or electric shock.

1. 1. What should I do if I notice unusual smells or smoke from the  

   unit?

If any unusual smells or smoke come from the unit, stop using
the product immediately. Disconnect the power source and contact
the service center. Continued use in such a condition may cause
fire or electric shock.

1. 1. Can I modify or disassemble the product?

No, never disassemble or modify this product in any way. Contact
the nearest service center if the product fails to operate
normally. Unauthorized modifications or attempted repair may cause
problems for which HANWHA is not liable.

1. 1. How should I clean the product?

When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock.

1. 1. Can I expose the product to direct airflow from an air  

   conditioner?

No, avoid exposing the product to direct airflow from an air
conditioner as it may cause moisture condensation inside the clear
dome due to temperature difference between internal and external of
the dome camera.

1. 1. How should I install the product in a low-temp area?

If you install this product in a low-temp area such as inside a
cold store, you must seal up the wiring pipe with silicon so that
the external air cannot flow inside the housing. Vapor inside the
product due to a difference between internal and external
temperature.

BOX CAMERA HOUSING
User Manual
SHB-4200 SHB-4200H

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. if any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power souroe and contact the service center. Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contach the nearest service center. Never disassemble or modify this product in any way. (HANWHA is not liable for problems caused by unauthorized modifications or attempted repair.
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock
11. Do not expose the product to the direct airflow from an air conditioner. Otherwise, it may cause moisture conden sation inside the clear Dome due to temperature difference between internal and external of the dome camera.
12. If you install this product in alow-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not flow inside the housing. vapor inside the product due to a difference between internal and external temperature.

%106’065

1. Safety Instructions

…………… 1

2. Product Overview

…………… 1

3. Features

…………… 2

4. Product Specifications …………… 3, 4

5. exterior

…………… 5

6. Installation

…………… 6

7. Installing the bracket …………… 7

1. Safety Instructions
The safety instructions below are prepared to avoid physical or monetary damage from an accident, so please read carefully and follow them. Do not install the product in a place that contains salt or produces the sulphurous gas. Do not insert metal objects or inflammable substances inside. Otherwise, it may cause an electric leakage or shock or a fire. Put a neutral detergent on the cloth that is used to wipe on the glass surface. Do not use chemical substances such as thinner and benzene. Use the right tools and wires to install the product in compliance with the safety instructions.
2. Product Overview
This CAMERA-HOUSING is designed to install the outdoor CCTV camera securely to protect it from the external conditionsU
1

3. Features
This product is a 14″ camera housing that is designed to guarantee that the outdoor CCTV camera is installed securely for stable operation. Firm and secure with the semi-permanent material, it is designed to be in harmony with the surrounding environment and to help the CCTV camera operate stably regardless of the dirt that may accumulate in the installation site and the weather condition. In addition to the waterproofness function, it has the hinges on both sides that are manufactured in the top cover structure, which facilitates the installation and repair work. The material of the body frame is made of aluminium that is corrosion-resistant; the front and rear sides of the housing are made of UV coating protective plastic. The product is also seamlessly sealed to protect itself from an unexpected external impact.
2

4. Product Specifications

1. Model Name : SHB-4200

2. Purpose

: Outdoor Housing

3. Product Name : CAMERA HOUSING

4. Features

: Dustproof, Sealed

5. Material

: Body ­ Aluminium AL A6063.

Front, Rear ­ ABS Incombustible

6. Use Condition : -15 ~ +45

7. Weight

: 1.0kg

8. Dimension

– Outside : 148mm(W) x 107mm(H) x 421mm(D)

– Inside : 84mm(W) x 78mm(H) x 319mm(D)

9. Color

– Ivory

10. Accessories

– Housing

: ¼”-20 Unc Screw (x3), Spring Washer (x1), Flat Washer (x1)

PG13.5 Cable Gland (x1), Wrench(x1), Wrench Screw (x2), Cushion Pad (x2)

– Bracket

: ¼”-20 Unc Screw (x2), Spring Washer (x2), Flat Washer (x2)

3

4. Product Specifications

1. Model Name : SHB-4200H

2. Purpose : Outdoor Housing

3. Product Name : CAMERA HOUSING

4. Features : Dustproof, Sealed

5. Material

: Body ­ Aluminium AL A6063.

Front, Rear ­ ABS Incombustible

6. Use Condition : -35 ~ +50

7. Weight

: 1.1kg

8. Input Power : AC 24V

9. Power Consumption : Heater – 20W, FAN ­ 1.6W

10. Operation Temperature : Heater 4 ±3 ON

FAN 45 ±5 ON

11. Dimension

– Outside : 148mm(W) x 107mm(H) x 421mm(D)

– Inside : 84mm(W) x 78mm(H) x 260mm(D)

12. Color

– Ivory

13. Accessories

– Housing

: ¼”-20 Unc Screw (x3), Spring Washer (x1), Flat Washer (x1) PG13.5 Cable Gland (x1),Wrench(x1), Wrench Screw (x2) Cushion Pad (x2)

– Bracket
: ¼”-20 Unc Screw (x2), Spring Washer (x2), Flat Washer (x2) 4

5. exterior
· Body · Front, Rear
· Mount Base
5

6. Installation
· Wiring Diagram (SHB-4200H)
· How to connect the BNC connector 1) Insert the cable to the cable gland from outside of the
product and connect it to the terminal block. 2) Connect the BNC connector to the cable and insert it to the
cable gland from inside. 3) Insert the cable to the concord from outside and connect it
the BNC connector.
6

7. Installing the bracket and the cushion pad
Location with cushion pad Depending on the size of the camera, the location
of the cushion pads may vary. 7

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>