Hanwha Vision SHP-1520FW In Ceiling Housing Instruction Manual

Hanwha Vision SHP-1520FW In Ceiling Housing

OVERVIEW

This In-CEILING HOUSING is a mounting ADAPTOR that is designed to mount the smart dome camera in built-in style on a double-layer ceiling.

WHAT’S INCLUDED

• Housing
  

• Safety Bracket (1EA)

• Safety Wire (1SET)
  

• Template (1EA)

• Screw (4EA)

• Installation Manual

• Fixing Bracket (1EA)

INSTALLATION INSTRUCTIONS

1. Select an installation position or place that can endure more than 4 times of the total weight of the installation structure.
2. At least 250mm or more of spare height is required above the CEILING BOARD.
3. CEILING BOARD’s thickness should be less than 40mm.
4. Be sure to secure the SAFETY WIRE to avoid a product fall.
5. If you want to attach the camera to the ADAPTOR, use the only provided SCREWS.
   

INSTALLATION

Applicable model : XNP-6320/XNP-6321/QNP-6230

1. Attach the installation template to the ceiling and mark its location with a pencil.
   

2. Attach the mount template to a surface you want and drill holes.
   

3. Connect the install base included in the PTZ camera to the housing for installation using the 4 screws that are included as accessories.
   

4. Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the ANCHOR BOLT as below:

5. Tighten the nut (“N1”) on the ANCHOR BOLT.

6. Insert the provided SAFETY BRACKET into the ANCHOR BOLT.

7. Tighten two nuts (“N2”,”N3”) onto the ANCHOR BOLT.

8. Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.

9. Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below.
   

  * The ANCHOR BOLTs and nuts are optional and not included in the product package.

5. Press the SNAP-FIT on the ADAPTOR to open it, and insert camera cables and external connection cables into the HOUSING through the hole (see figure below).

   •  Refer to the installation manual of the camera that you want to install, and prepare necessary
     cables for camera connection.
     

6. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the SCREWs (x2) clockwise to fix the HOUSING on the CEILING. (The BRACKET will be positioned from to as shown.)

   •  Ensure that the HOUSING is firmly secured to the CEILING BOARD.
     

7. Camera Cable Arrangement and Hinged Door Close Connect the cable to the terminal block on the hinged door. Please refer to ‘Camera Cabling Diagram’ in the installation manual.
   After cabling, please close the hinged door.
   

8. Camera Installation
   Insert the fixing bracket into the camera bezel. Connect the safety cable first, and then assemble the camera. The safety cable is wound around the install base like a spring. Pull from the install base as shown in the figure below to mount onto the hook of the safety cable.
   After mounting the install base as shown in the figure, turn the unit in a clockwise direction. After turning the unit, connect the screw on the fixing bracket to the lower bracket.

   • To attach the camera to the mount, refer to the alignment guide marks as shown in the figure.
     
     Alignment Directions
     

9. Mount the case top into the housing.
   

PRODUCT SPECIFICATIONS

Unit : mm[Inch]

Documents / Resources

| Hanwha Vision SHP-1520FW In Ceiling Housing [pdf] Instruction Manual
SHP-1520FW, XNP-6320, XNP-6321, QNP-6230, SHP-1520FW In Ceiling Housing, SHP- 1520FW, In Ceiling Housing, Ceiling Housing, Housing
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>