DEWALT DCD85M McLaren Design Cordless Combi Drill Instruction Manual

June 15, 2024
Dewalt

DEWALT DCD85M McLaren Design Cordless Combi Drill

  • HAMMERDRILL DCD85M
  • Congratulations!
    • You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.

Technical Data

                                                                  DCD85M

Voltage| VDC| 18
Type| | 1
Battery type| | Li‑Ion
No‑load speed| |
1st gear| min‑1| 0–650
2nd gear| min‑1| 0–2000
Impact rate| |
1st gear| min‑1| 0‑11050
2nd gear| min‑1| 0‑34000
Max. torque (hard/soft)| Nm| 90/27
Chuck capacity| mm| 1.5–13.0
Maximum drilling capacity| |
Wood| mm| 55
Metal| mm| 13
Masonry| mm| 13
Weight (without battery pack)| kg| 1.34
| |
Noise values and/or vibration values (triax vector sum) according to EN62841‑2‑1:
LPA (emission sound pressure level)| dB(A)| 93
LWA (sound power level)| dB(A)| 101
K  (uncertainty for the given sound level)| dB(A)| 5
| |
Drilling into metal| |
Vibration emission value ah,D =| m/s2| < 2.5
Uncertainty K =| m/s2| 1.5
Drilling into concrete| |
Vibration emission value ah,ID =| m/s2| 11
Uncertainty K =| m/s2| 1.5

  • The vibration and/or noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN62841and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
  • WARNING: The declared vibration and/or noise emission level represents the main applications of the tool. However, if the tool is used for different applications, with different accessories or is poorly maintained, the vibration and/or noise emission may differ. This may significantly increase the exposure level over the total working period.
  • An estimation of the level of exposure to vibration and/or noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
  • Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm (relevant for vibration), organisation of work patterns.

EC‑Declaration of Conformity
Machinery Directive

Impact Drill
DCD85M

  • DEWALT declares that these products described under Technical Data are in compliance with:
    • 2006/42/EC, EN 62841-1:2015 + AC:2015 + A11:2022; EN 62841-2-1:2018+A11:2019.
  • These products also comply with Directive 2014/30/EU and 2011/65/EU.
  • For more information, please contact DEWALT at the following address or refer to the back of the manual.
  • The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.
  • Markus Rompel
  • Vice-President Engineering, PTE-Europe
  • DEWALT, Richard-Klinger-Straße 11,
  • 65510, Idstein, Germany
  • 8.12.2022

DECLARATION OF CONFORMITY

  • THE SUPPLY OF MACHINERY (SAFETY)  REGULATIONS 2008
  • IMPACT DRILL DCD85M
  • DEWALT declares that these products described under Technical Data are in compliance with:
  • The Supply of Machinery (Safety) Regulations, 2008, S.I. 2008/1597 (as amended),
  • EN 62841-1: 2015 + AC:2015 + A11:2022; EN 62841-2-1:2018+A11:2019.

These products conform to the following UK Regulations:

Batteries Chargers/Charge Times **(Minutes)*****
**** Cat # **** VDC
DCB1102 DCB113
DCB546 18/54
DCB547/G 18/54

X
DCB548| 18/54| 12.0/4.0| 1.46| 120| 540| 350| 300| 180| 150| 80| 120| 180| X
DCB549| 18/54| 15.0/5.0| 2.12| 125| 730| 450| 380| 230| 170| 90| 125| 230| X
DCB181| 18| 1.5| 0.35| 22| 70| 45| 35| 22| 22| 22| 22| 22| 45
DCB182| 18| 4.0| 0.61| 60/40| 185| 120| 100| 60| 60/45| 60/40| 60/40| 60| 120
DCB183/B/G| 18| 2.0| 0.40| 30| 90| 60| 50| 30| 30| 30| 30| 30| 60
DCB184/B/G| 18| 5.0| 0.62| 75/50| 240| 150| 120| 75| 75/60| 75/50| 75/50| 75| 150
DCB185| 18| 1.3| 0.35| 22| 60| 40| 30| 22| 22| 22| 22| 22| 40
DCB187| 18| 3.0| 0.54| 45| 140| 90| 70| 45| 45| 45| 45| 45| 90
DCB189| 18| 4.0| 0.54| 60| 185| 120| 100| 60| 60| 60| 60| 60| 120
DCBP034/G| 18| 1.7| 0.32| 27| 82| 50| 40| 27| 27| 27| 27| 27| 50
DCBP518/G| 18| 5.0| 0.75| 50| 240| 150| 120| 75| 60| 50| 50| 75| 150

  • *Date code 201811475B or later
  • **Date code 201536 or later
  • ***Battery charge times matrix provided for guidance only; charge times will vary depending on temperature and condition of batteries.

Electromagnetic Compatibility Regulations, 2016, S.I.2016/1091 (as amended).

  • The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, S.I. 2012/3032 (as amended).
  • For more information, please contact DEWALT at the following address or refer to the back of the manual.
  • The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.
    • Karl Evans
  • Vice President Professional Power Tools EANZ GTS DEWALT UK, 270 Bath Road, Slough
    • SL1 4DX
  • England
    • 8.12.2022

WARNING: To reduce the risk of injury, read the instruction manual.

Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

  • DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
  • WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
  • CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
  • NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
    • ****Denotes risk of electric shock.
    • ****Denotes risk of fire.

GENERAL POWER TOOL SAFETY WARNINGS

  • WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

  1. Work Area Safety

  2. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

  3. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

  4. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

  5. Electrical Safety

  6. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.  Unmodified plugs and atching outlets will reduce risk of electric shock.

  7. Avoid body contact with earthed or grounded  surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

  8. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

  9. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

  10.  When operating a power tool outdoors, use an
    extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

  11. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

  12. Personal Safety

  13. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

  14. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

  15. Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

  16. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

  17. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

  18.  Dress properly. Do not wear loose clothing or  jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

  19.  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

  20. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

  21. Power Tool Use and Care

  22.  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

  23.  Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

  24.  Disconnect the plug from the power source and or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

  25. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

  26. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

  27. Keep cutting tools sharp and clean. Properly
    maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

  28. Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

  29. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

  30. Battery Tool Use and Care

  31. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

  32. Use power tools only with specifically designated
    battery packs. Use of any other battery packs may create a risk of injury and fire.

  33. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

  34. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

  35. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
    Do not expose a battery pack or tool to fire or  excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.

  36. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

  37. Service

  38.  Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

  39. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorised service providers.

Drill Safety Warnings
Safety Instructions for All Operations

  • Hold the power tool by insulated gripping surfaces when performing an operation where the cutting accessory or fasteners may contact hidden wiring.
  • Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety Instructions When Using Long Drill Bits

  • Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
  • Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
  • Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

Additional Specific Safety Rules for Drills/Drivers/Impact Drills

  • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
  • wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eye damage.
  • Drill bits and tools get hot during operation. Wear gloves when touching them.
  • Air vents often cover moving parts and should be avoided. Loose clothes, jewellery or long hair can be caught in moving parts.

Residual Risks

  • In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:
    • Impairment of hearing.
    • Risk of personal injury due to flying particles.
    • Risk of burns due to accessories becoming hot during operation.
    • Risk of personal injury due to prolonged use.

SAVE THESE INSTRUCTIONS

  • Chargers

    • DEWALT chargers require no adjustment and are designed to be as easy as possible to operate.
  • Electrical Safety

    • The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.
    • Your DEWALT charger is double insulated in accordance with EN60335; therefore, no earth wire is required.
    • If the supply cord is damaged, it must be replaced only by DEWALT or an authorised service organisation.
    • Mains Plug Replacement (U.K. & Ireland Only)
  • If a new mains plug needs to be fitted:

    • Safely dispose of the old plug.
    • Connect the brown lead to the live terminal in the plug.
    • Connect the blue lead to the neutral terminal.
      WARNING: No connection is to be made to the  earth terminal.
  • Follow the fitting instructions supplied with good quality plugs.

    • Recommended fuse: 3 A.

Using an Extension Cable

  • An extension cord should not be used unless absolutely necessary. Use an approved extension cable suitable for the power input of your charger (refer to Technical Data). The minimum conductor size is 1 mm2; the maximum length is 30 m.
  • When using a cable reel, always unwind the cable completely

Important Safety Instructions for All Battery Chargers

  • SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for compatible battery chargers (refer to Technical Data). Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
  • WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.
  • WARNING: We recommend the use of a residual current device with a residual current rating of 30 mA or less.
  • CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  • CAUTION: Children should be supervised to ensure that they do not play with the appliance.
  • NOTICE: Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.
  • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.
  • These chargers are not intended for any uses other than charging DEWALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.
  • Do not expose charger to rain or snow.
  • Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.
  • Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
  • Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock, or electrocution.
  • Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is  ventilated through slots in the top and the bottom of the housing.
  • Do not operate charger with damaged cord or plug—have them replaced immediately.
  • Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorised service centre.
  • Do not disassemble charger; take it to an authorised service centre when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
  • In case of damaged power supply cord, the supply cord must be replaced immediately by the manufacturer, its service agent or similar qualified person to prevent any hazard.
  • Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
  • NEVER attempt to connect two chargers together.
  • The charger is designed to operate on standard 230V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.

Charging a Battery (Fig. B)

  1. Plug the charger into an appropriate outlet before inserting battery pack.
  2. Insert the battery pack  11  into the charger, making sure the battery pack is fully seated in the charger. The red (charging) light will blink repeatedly, indicating that the charging process has started.
  3. The completion of charge will be indicated by the red light remaining ON continuously. The battery pack is fully charged and may be used at this time or left in the charger. To remove the battery pack from the charger, push the battery release button  12  on the battery pack.

NOTE: To ensure maximum performance and life of lithium-ion battery packs, charge the battery pack fully before first use.
Charger Operation
Refer to the indicators below for the charge status of the battery pack.

  • The red light will continue to blink, but a yellow indicator light will be illuminated during this operation. Once the battery pack has reached an appropriate temperature, the yellow light will turn off and the charger will resume the charging procedure.

  • The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty battery by refusing to light.
    NOTE: This could also mean a problem with a charger.

  • If the charger indicates a problem, take the charger and battery pack to be tested at an authorised service centre.

Hot/Cold Pack Delay

  • When the charger detects a battery pack that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery pack life. A cold battery pack will charge at a slower rate than a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery pack warms.
  • The DCB118 charger is equipped with an internal fan designed to cool the battery pack. The fan will turn on automatically when the battery pack needs to be cooled. Never operate the charger if the fan does not operate properly or if ventilation slots are blocked. Do not permit foreign objects to enter the interior of the charger.

Electronic Protection System

  • XR Li-Ion tools are designed with an Electronic Protection System that will protect the battery pack against overloading, overheating or deep discharge.
  • The tool will automatically turn off if the Electronic Protection System engages. If this occurs, place the lithium-ion battery pack in the charger until it is fully charged.

Wall Mounting

  • These chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 25.4 mm long with a screw head diameter of 7–9 mm, screwed into wood to an optimal depth leaving approximately 5.5 mm of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots.

Charger Cleaning Instructions

  • WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
  • Battery Packs
    Important Safety Instructions for All Battery Packs When ordering replacement battery packs, be sure to include catalogue number and voltage.
    The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

  • Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.

  • Never force battery pack into charger. Do not modify battery pack in any way to fit into a non‑compatible charger as battery pack may rupture, causing serious personal injury.

  • Charge the battery packs only in DEWALT chargers.

  • DO NOT splash or immerse in water or other liquids.

  • Do not store or use the tool and battery pack in locations where the temperature may fall below 4 ˚C (39.2 ˚F)
    (such as outside sheds or metal buildings in winter), or reach or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal buildings in summer).

  • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs are burned.

  • If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

  • Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.

  • WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

  • WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with
    a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to service centre for recycling.

  • WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

  • CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.

Transportation

  • WARNING: Fire hazard. Transporting batteries can possibly cause fire if the battery terminals inadvertently come into contact with conductive materials. When transporting batteries, make sure that the battery terminals are protected and well-insulated from materials that could contact them and cause a short circuit.

  • NOTE: Lithium-ion batteries should not be put in checked baggage.

  • DEWALT batteries comply with all applicable shipping regulations as prescribed by industry and legal standards, which include UN Recommendations on the Transport of

  • Dangerous Goods; International Air Transport Association (IATA) Dangerous Goods Regulations; International Maritime Dangerous Goods

  • (IMDG) Regulations; and the European Agreement Concerning The International Carriage of Dangerous Goods by Road

  • (ADR). Lithium-ion cells and batteries have been tested to section 38.3 of the UN Recommendations on the Transport of Dangerous Goods Manual of Tests and Criteria.

  • In most instances, shipping a DEWALT battery pack will
    be excepted from being classified as a fully regulated

  • Class 9 Hazardous Material. In general, only shipments containing a lithium-ion battery with an energy rating greater than 100 Watt Hours (Wh) will require being shipped as fully regulated Class 9. All lithium-ion batteries have the Wh rating marked on the pack. Furthermore, due to regulation complexities, DEWALT does not recommend air shipping lithium-ion battery packs alone regardless of Wh rating. Shipments of tools with batteries (combo kits) can be air shipped as excepted if the Wh rating of the battery pack is no greater than 100 Wh.

  • Regardless of whether a shipment is considered excepted or fully regulated, it is the shipper’s responsibility to consult

  • the latest regulations for packaging, labeling/marking and documentation requirements.

  • The information provided in this section of the manual is provided in good faith and believed to be accurate at the time the document was created. However, no warranty, expressed or implied, is given. It is the buyer’s responsibility to ensure that its activities comply with the applicable regulations. Transporting the FLEXVOLTTM Battery

  • The DEWALT FLEXVOLT® battery has two modes: Use and Transport.

  • Use Mode: When the FLEXVOLTTM battery stands alone or is in a DEWALT 18V product, it will operate as an 18V battery. When the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries) product, it will operate as a 54V battery.

  • Transport Mode : When the cap is attached to the FLEXVOLTTM battery, the battery is in Transport mode. Keep the cap for shipping.

  • When in Transport mode, strings of cells are electrically disconnected within the pack, resulting in 3 batteries with a
    lower Watt hour (Wh) rating as compared to 1 battery with a higher Watt hour rating. This increased quantity of 3 batteries with the lower Watt hour rating can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries.

  • For example, the Transport Example of Use and Transport Label Marking Wh rating might indicate

    • 3 x 36 Wh, meaning
    • 3 batteries of 36 Wh each.
  • The Use Wh rating might  indicate 108 Wh (1 battery implied).

Storage Recommendations

  1. The best storage place is one that is cool and dry away from direct sunlight and excessive heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
  2. For long storage, it is recommended to store a fully charged battery pack in a cool, dry place out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger and the battery pack may show the following pictographs:

  • Read instruction manual before use.
  • Refer to Technical Data for charging time.
  • Do not probe with conductive objects.
  • Do not charge damaged battery packs.
  • Do not expose to water.
  • Have defective cords replaced immediately.
  • Charge only between 4 ˚C and 40 ˚C.
  • Only for indoor use.
  • Discard the battery pack with due care for the environment.
  • Charge DEWALT battery packs only with designated DEWALT chargers. Charging battery packs other than the designated DEWALT batteries with a DEWALT charger may make them burst or lead to other dangerous situations.
  • Do not incinerate the battery pack.
  • USE (without transport cap). Example: Wh rating indicates 108 Wh (1 battery with 108 Wh).
  • TRANSPORT (with built-in transport cap). Example: Wh rating indicates 3 x 36 Wh (3 batteries of 36 Wh).

Battery Type

  • The following tools operate on an 18-volt battery pack: DCD85M.
  • These battery packs may be used: DCB181, DCB182, DCB183, DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185, DCB187, DCB189, DCBP034, DCBP034G, DCBP518,
  • DCBP518G, DCB546, DCB547, DCB547G, DCB549. Refer to Technical Data for more information.

Package Contents

  • The package contains:
  • 1 Drill/driver/hammer drill
  • 1 Charger
  • 1 Li-Ion battery pack (C1, D1, E1, G1, H1, L1, M1, P1, Q1, S1, T1, U1, X1 models)
  • 2 Li-Ion battery packs (C2, D2, E2, G2, H2, L2, M2, P2, Q2, S2, T2, U2, X2 models)
  • 3 Li-Ion battery packs (C3, D3, E3, G3, H3, L3, M3, P3, Q3, S3, T3, U3, X3 models)

Instruction manual

  • NOTE: Battery packs, chargers and kitfoxes are not included with N models. Battery packs and chargers are not included with NT models. B models include Bluetooth®  battery packs.
  • NOTE: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth®, SIG, Inc. and any use of such marks by DEWALT is under license. Other trademarks and trade names are those of their respective owners.
  • Check for damage to the tool, parts or accessories which may have occurred during transport.
  • Take the time to thoroughly read and understand this manual prior to operation.

Markings on Tool

  • The following pictograms are shown on the tool:
    • Read instruction manual before use.
    • Visible radiation. Do not stare into light.

Date Code Position (Fig. B)
The production date code  14  consists of a 4-digit year followed by a 2-digit week and is extended by a 2-digit factory code.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

  1. Trigger switch
  2. Forward/reverse control button
  3. Torque adjustment collar
  4. Gear shifter
  5. Worklight
  6. Keyless chuck
  7. Chuck sleeve
  8. Belt hook
  9. Mounting screw
  10. Bit holder
  11. Battery pack
  12. Battery release button
  13. Worklight switch

Intended Use

  • These drills/drivers/hammerdrills are designed for professional drilling, percussion drilling and screwdriving applications.

  • DO NOT use under wet conditions or in the presence of flammable liquids or gases.
    These drills/drivers/hammerdrills are professional power tools.

  • DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

  • Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision.

  • This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS

  • WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury.
  • Inserting and Removing the Battery Pack from the Tool (Fig. B)
  • NOTE: Make sure your battery pack  11  is fully charged.

To Install the Battery Pack into the Tool Handle

  1. Align the battery pack with the rails inside the tool’s handle (Fig. B).
  2. Slide it into the handle until the battery pack is firmly seated in the tool and ensure that you hear the lock snap into place.

To Remove the Battery Pack from the Tool

  1. Press the battery release button  12  and firmly pull the battery pack out of the tool handle.
  2. Insert battery pack into the charger as described in the charger section of this manual.

Fuel Gauge Battery Packs (Fig. B)

  • Some DEWALT battery packs include a fuel gauge, which consists of three green LED lights that indicate the level of charge remaining in the battery pack.
  • To actuate the fuel gauge, press and hold the fuel gauge button  15 . A combination of the three green LED lights will illuminate, designating the level of charge left. When the level of charge in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged. NOTE: The fuel gauge is only an indication of the charge left on the battery pack. It does not indicate tool functionality and is subject to variation based on product components, temperature and end-user application.

Belt Hook and Magnetic Bit Holder (Fig. A)

  • Optional Accessories
    • WARNING: To reduce the risk of serious personal injury, ONLY use the tool’s belt hook to hang the tool from a work belt.
    • DO NOT use the belt hook for tethering or securing the tool to a person or object during use.
    • DO NOT suspend tool overhead or suspend objects from the belt hook.
    • WARNING: To reduce the risk of serious personal injury, ensure the screw holding the belt hook is secure.
    • CAUTION: To reduce the risk of personal injury or damage,
    • DO  NOT use the belt hook to hang the drill while using as a spotlight.

IMPORTANT: When attaching or replacing the belt hook  8  or magnetic bit holder  10 , use only the mounting screw  9  that is provided. Be sure to securely tighten the screw.

  • The belt hook and magnetic bit holder can be attached to either side of the tool using only the screw provided, to accommodate left- or right-handed users. If the hook or magnetic bit holder is not desired at all, it can be removed from the tool.
  • To move belt hook or magnetic bit holder, remove the screw that holds it in place, then reassemble on the opposite side. Be sure to securely tighten the screw.
  • Variable Speed Trigger Switch (Fig. A)
  • To turn the tool on, squeeze the variable speed trigger switch  1 . To turn the tool off, release the trigger switch. Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully released.
  • NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should
    be avoided.

Forward/Reverse Control Button (Fig. A)

  • A forward/reverse control button  2  determines the direction of the tool and also serves as a lock-off button.
  • To select forward rotation, release the trigger switch and depress the for ward/re verse control button on the right side of the tool.
  • To select reverse, release the trigger switch and depress the forward/reverse control button on the left side of the tool.
  • The centre position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released.
  • NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start-up. This is normal and does not indicate a problem.

Torque Adjustment Collar (Fig. A)

  • Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some models, a hammer mechanism for drilling into masonry.
  • Circling the torque adjustment collar  3  are numbers, a drill bit symbol, and on some models, a hammer symbol. These numbers are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener which can be driven. To select any of the numbers, rotate until the desired number aligns with the arrow.

Dual Range Gearing (Fig. A)
The dual range feature of your drill/driver allows you to shift gears for greater versatility.

  1. To select speed 1 (high torque setting), turn the tool off and permit it to stop. Slide the gear shifter  4  forward (towards the chuck).
  2. To select speed 2 (low torque setting), turn the tool off and permit it to stop. Slide the gear shifter back (away from the chuck).

NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete stop before changing gears. If you are having trouble changing gears, make sure that the dual range gear shifter is either completely pushed forward or completely pushed back.
Pivoting LED Worklight (Fig. A, E)

  • CAUTION: Do not stare into worklight. Serious eye  injury could result.
  • The worklight  5  located on the foot of the tool is activated when the trigger switch is depressed and is adjustable via three detent positions. The off  17 , on  18 , and spotlight  19  modes can be changed by moving the worklight switch  13  on the foot of tool. In the on setting, the worklight will stay illuminated for up to 20 seconds. If the trigger switch remains  depressed, the worklight will remain on.
  • NOTE: The worklight is for lighting the immediate work surface and are not intended to be used as a flashlight.
  • Spotlight Mode
  • The spotlight will run for 20 minutes after the trigger switch is released. Two minutes before the spotlight will shut off, it will flash twice and then dim. To avoid the spotlight shutting off, lightly tap the trigger switch.
  • WARNING: While using the worklight in medium or spotlight mode, do not stare at the light or place the drill in a position which may cause anyone to stare into the light. Serious eye injury could result.
  • CAUTION: When using the tool as a spotlight, be sure it is secured on a stable surface where it will not cause a tripping or falling hazard.
  • CAUTION: Remove all accessories from the chuck before using the drill as a spotlight. Personal injury or property damage could result.

Low Battery Warning

  • When in spotlight mode and the battery is nearing complete discharge, the spotlight will flash twice and then dim. After two minutes, the battery will be completely discharged and the drill will immediately shut down. At this point, replace with a fresh battery.
  • WARNING: To reduce the risk of injury, always have a back-up battery or secondary lighting available if the situation warrants it.

Keyless Single Sleeve Chuck (Fig. C)

  • WARNING: Do not attempt to tighten drill bits (or
    any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may result. Always lock off trigger switch and remove the battery from the tool when changing accessories.

  • WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject from tool, causing possible personal injury.

Your tool features a keyless chuck  6  with one rotating chuck sleeve  7  for one-handed operation of the chuck. To insert a drill bit or other accessory, follow these steps.

  1. Turn tool off and remove the battery pack.
  2. Grasp the black sleeve of the chuck with one hand and use the other hand to secure the tool. Rotate the sleeve anticlockwise (as viewed from the front) far enough to accept the desired accessory.
  3. Insert the accessory about 19 mm into the chuck and tighten securely by rotating the chuck sleeve clockwise with one hand while holding the tool with the other hand. Continue to rotate the chuck sleeve until several ratchet clicks are heard to ensure full gripping power.
    NOTE: Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for maximum tightness. To release the accessory, repeat steps 1 and 2 above.

OPERATION

Instructions for Use

  • WARNING: Always observe the safety instructions and applicable regulations.
  • WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury.

Proper Hand Position (Fig. D)

  • WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.
  • WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.
    Proper hand position requires one hand on the main handle  16  and one hand on the battery pack.

Drill Operation (Fig. A, D)
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, ALWAYS ensure workpiece is anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the material.

  1. Turn the collar  3  to the drill symbol.

  2. Select the desired speed/torque range using the
    gear shifter  4  to match the speed and torque to the planned operation.

  3. For Wood, use twist bits, spade bits, power auger bits or hole saws. For Metal, use high-speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry.

  4. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but do not push hard enough to stall the motor or deflect the bit.

  5. Hold tool firmly with both hands to control the twisting action of the drill. If model is not equipped with side handle, grip drill with one hand on the handle and one hand on the battery pack.
    CAUTION: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly to control the twisting action and avoid injury.

  6. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL — THIS CAN DAMAGE THE DRILL.

  7. To minimise stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole.

  8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming.

  9. With variable speed drills there is no need to centre punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep enough to drill without the bit skipping out.

Hammerdrill Operation (Fig. A, D)

  1. Turn the collar  3  to the hammerdrill symbol.

  2. Select the high speed setting by sliding the gear shifter  4  back (away from the chuck).
    IMPORTANT: Use carbide-tipped or masonry bits only.

  3. Drill with just enough force on the hammer to keep it from bouncing excessively or “rising” off the bit. Too much force will cause slower drilling speeds, overheating and lower drilling rate.

  4. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit when drillling as this will cause clogging of the bit flutes and a slower drilling speed.

  5. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with tool still running to help clear debris from the hole.
    NOTE: A smooth, even flow of dust from the hole indicates proper drilling rate.

Screwdriver Operation (Fig. A, D)

  1. Turn the torque adjustment collar  3  to the desired position.

  2. Select the desired speed/torque range using the gear shifter  4  to match the speed and torque of the planned operation.
    NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The lower the number, the lower the torque output.

  3. Insert the desired fastener accessory into the chuck as you would any drill bit.

  4. Make some practice runs in scrap or on unseen areas to determine the proper position of the clutch collar.

  5. Always start with lower torque settings, then advance to higher torque settings to avoid damage to the workpiece or fastener.

MAINTENANCE

  • Your power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.
  • WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury.
    • The charger and battery pack are not serviceable.
  • Lubrication
    • Your power tool requires no additional lubrication.
  • Cleaning
    • WARNING: Electrical shock and mechanical hazard. Disconnect the electrical appliance from the power source before cleaning.
    • WARNING: To ensure safe and efficient operation, always keep the electrical appliance and the ventilation slots clean.
    • WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
  • Ventilation slots can be cleaned using a dry, soft non-metallic brush and/or a suitable vacuum cleaner. Do not use water or any cleaning solutions. Wear approved eye protection and an approved dust mask.

Optional Accessories

  • WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT-recommended accessories should be used with this product. Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

  • Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste.
  • Products and batteries contain materials that can be recovered or recycled, reducing the demand for raw materials.
  • Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com.

Rechargeable Battery Pack

  • This long‑life battery pack must be recharged when it fails to produce sufficient power on jobs that were easily done before. At the end of its technical life, discard it with due care for our environment:
    • Run the battery pack down completely, then remove it from the tool.
    • Li‑Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly
  • DeWALT, 270 Bath Road;
  • Slough, Berks SL1 4DX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Dewalt User Manuals

Related Manuals