SG 44 Steam Cleaner and Hand Steamer Instruction Manual

STEAM CLEANER MANUAL

SAFETY INSTRUCTIONS

User guide and safety instructions. The appliance should be disconnected from the mains after use and before cleaning. Read all these instruction carefully before use.

• Do not direct steam at people, animals or at electrical devices.
• Do not operate machine without water in the tank.
• Do not allow machine to run unattended at any time.
• Close supervision is necessary when this machine is used near children. Do not allow it to be used as a toy.
• The machine is designed for household use only, do not expose to rain.
• Do not overfill the water tank. The machine contains a maximum of 1500ml of water only.
• Excessive filling of the water tank may cause damage of injury.
• Never turn the machine over or tilt more than 45’ when it is switched on or if it’s still producing steam.
• Never use this machine to clean electronic devices or installations.
• Do not run steam cleaner for more than 1 hour at a time.
• Use extra care when cleaning on stairs.
• Do not immerse cord, plug or machine in water or any other liquid.
• Do not operate with a damaged cord, if the power cord is damaged or any improper performance of this machine occurs it should be repaired by a qualified electrician only.
• Keep hair, loose clothing, fingers, feet and all parts of body away from the jet of steam.
• Do not operate machine in bare feet or when wearing open toe shoes or sandals.
• Do not pull or carry by cord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. Keep cord away from heated surfaces.
• Unplug cleaner when not in use. Turn all controls off before unplugging from mains.
• Do not unplug by pulling on cord. Always grasp the plug, not the cord. Never handle plug or appliance with wet hands.
• Store in a dry place. Do not expose machine to freezing temperatures.
• Do not try to repair the appliance yourself. Contact a qualified technician. To avoid danger, a defective cable should be replaced only with an equivalent cable and by the manufacturer, our after sales service or someone with a similar qualification.
• Use only original accessories.
• Regularly check the appliance and the cable. Do not switch the appliance on if it is damaged.
• NEVER open the Pressure Cap during use unless you have correctly followed the instructions elsewhere in this guide. The Pressure Cap gets hot in use; handle it with care.

MACHINE ACCESSORIES/DESCRIPTION

Accessories 11, 12, 19, 20, and 21 are stored beneath the tool storagelid (2).
HOW TO ASSEMBLE YOUR STEAM CLEANER
NOTE: Tool accessories are located in the front section of machine itself.
FILLING THE WATER TANK:

1. Make sure the machine is unplugged from the main.
2. Unscrew the safety cap by pushing down and turning anti clockwise.
3. Use the beaker (17) and funnel (16) to fill the machine with up to 1500ml of water. This should be sufficient to use the steam cleaner for approximately 45 minutes.
4. Once full, replace the safety cap by turning clockwise, and fasten tightly.

RE-FILLING THE WATER TANK DURING USE:
WARNING!: Great care must be taken with this process. Failure to follow this procedure will present the danger of scalding!

1. Switch the machine off using the on/off button.

2. Disconnect the power cable from the main. Wait 5 minitues.

3. Lift the machine off the floor and “Rock” the machine. Left, right, forwards, backwards, then squeeze the steam trigger to release any steam pressure.

4. Wait 5 minutes.

5. Squeeze the steam trigger to release any steam pressure.

6. At arms length attempt to unscrew the pressure cap-wich may be hot to touch! If the cap starts to unscrew, continue slowly in case there has been any further build-up of steam. Turn your head away before fully unscrewing the safety cap. DO NOT FULLLY uncrew the safety cap until any remaning steam pressure has dissipated. If the cap will not unscrew, wait 5 minutes and repeat steps 3 to 6 inclusive.

7. Fill the water tank as necessary using the funnel provided, to 1500ml maximum.

8. Replace the safety cap by turning clockwise. Fasten cap tightly, you are not ready to switch the machine on.
   NOTE: tool accessories are located in the front section of the machine itself.

TURNING THE MACHINE ON:

1. When the water tank has been filled attach the accessory or floor cleaning tool you require to the machine .
2. Now plug the machine into the mains (230V/50Hz) and turn on using the switch at the rear of the cleaner.
3. The machine will build up steam pressure, When the indicator light goes off, the machine is ready, If will take up to 10 minutes to reach the correct pressure level, depending on the amount of water in the tank.

NOTE: The indicator light may come on when the machine is in use. If this happens, release the safety button to close the steam trigger and allow the steam pressure to build up once again. This should take no longer than 40 seconds.
WARNING: If the steam trigger is pressed when the indicator light is on, hot water may be expelled instead of steam.
TURNING THE MACHINE OFF.
Turn of the machine using the same switch at the rear of the cleaner, Now follow the after care instruction. The steam gun has a steam trigger (9) and a safety button (10).
The safety buttons is marked ON and OFF/LOCK.
INTERMITTENT STEAM SPRAY:
Press the safety button to the ON position and then squeeze the steam trigger. Steam comes out whenever the steam trigger is squeezed.

CONTINUOUS STEAM SPRAY:
If you want a continuous spray of steam, squeeze the steam trigger, then press the safety button to the OFF/LOCK position.

CLOSE STEAM GUN:
When you have finished steam cleaning. Press the safety button to the ON position. The steam trgger will release. Then press the safety button to the OFF/LOCK position, to lock the steam trigger closed.

HOW TO USE YOUR STEAM CLEANER

The accessories allow you to use the power of steam to blast away grease, grime, midew, scum, dust mites, fleas and harmful germs from difficult-to- reach places-with minimum effort and without chemicals. All wands and accessories snap-lock into place for a leak-free operation.
ATTACHING ADAPTORS:

1. Push the straight adaptor (12) as far as will go onto the steam gun nozzle until you hear a click.
2. To fit any of the accessoires (19, 20& 22) ensure that straight adaptor (12) is fitted securely and then simply push your chosen accessory.

ATTACHING EXTENSION TUBES:
Two extension tubes allow you to select various lengths for comfortable operation, reducing the need to bend and enabling you to reach high places.

1. To fit the extension tubes (14), simply remove the straight adaptor (12) from the steam gun and push the first extension tube as far as it will go onto the steam gun nozzle until you hear a click.
2. If you require the second tube to add extra length push your second tube onto the end of first tube until you hear a click.
3. Once you are happy with height of the extension tube you can now push on one of the adaptors (12 or 11) until you hear a click. The adaptor you choose will depend on your cleaning task.

CLEANING FLOORS.
It is recommended to sweep or vacuum your floor prior to using the mop.
The floor brush (18) is attached to the extension tubes, using the angled adaptor (11). It has spring-loaded clips to hold the cleaning cloth, Its brush bristles loosen dirt and open fibers for steam to penetrate.

1. Push the angled adaptor into the floor brush and twist through 180 degrees to attach.
2. Attach the floor brush to the extension tubes, using the adaptor. Then attach the extension tube to the steam gun.
3. Ensure the extension tubes are firmly connected. To release the extension tubes press the button on each connection.

CLEANING FLOOR & CAPRETS WITH THE FLOOR CLOTH:
While the machine is witched off, attach the floor cloth (13) to the floor brush using the spring-loaded clips, making sure the edges of the cleaning cloth are secured.

DO NOT attempt to do this while the machine is still hot, Never remove the floor cloth while the safety trigger is released or the machine is warm to the touch.
THE FLOOR CLOTH:
These are machine washable, Easily fits to the floor brush via spring-loaded and absorb dirty from sensitive cleaning surfaces.
ROUND BRUSHES (20, 21)
These are essential for cleaning hard-to-reach areas, Use on tile grout and bathroom fittings, These small, round brushes fit on the end of the steam gun, using the straight adaptor (12).

ANGLED NOZZLE (19):
Allows concentrated high pressure steam flow, connects directly to the steam gun using (6) straight adaptor.
SQUEEGEE (22):
Attach to the garment steam and use on mirrors, windows or other smoth surfaces, Steam Loosens surface dirty and the rubber blade of the squeegee (22) scrapes it clean.

BEAKER (17):
Use the measuring jug to ensure you fill the machine with the correct amount of water.
WATER FUNNEL (16):
The funnel ensures no mess when filling the tank!
HELP! I THINK MY STEAM CLEANER HAS A PROBLEM.
Water comes out of the nozzle
The Steam Cleaner develops a massive amount of steam. This may condense as water or water droplets in the steam hose and tools and nozzle, which are then expelled when used after a period of cooling. This is normal and not a cause for concern.
No steam comes out
Check in case the hose has become kinked or blocked, or that you have run out of water or
power!
I can’t get the pressure cap off
Make sure that you have wholly de-pressurized the boiler See the section REFILLING WITH WATER IN USE.
I have hard water and use boiled water from the kettle, or water that I left in the boiler, now my Steam Cleaner doesn’t work well at all.
Boiled water concentrates the minerals that form lime scale rather than boiling them away.
Water left in the boiler will go off and may create a reaction with the boiler and/or the steam hose. So, ALWAYS empty the machine after use and NEVER use boiled water.
WE WILL BE PLEASED TO HELP YOU WITH ANY QUESTIONS.
+31 6 87570777
Send us a message on Whatsapp! This is not a number for calling.
[email protected]
THANK YOU FOR CHOOSING

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>