mr steam MS400EB1 Hydro iSteamAQX Steambbath Generator Instruction Manual

Mr steam MS400EB1 Hydro iSteamAQX Steambbath Generator

READ ME FIRST!

WARNING As you follow these instructions, you will notice warning and caution symbols. This blocked intormation is important for the state and eft icient installation and operation of this generator. These are types of potential hazards that may occur during installation and operation:

WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION Indicates a potentially hazardous situation, which, if not avoided may result in minor or moderate injury or product damage.
IMPORTANT NOTE: This highlights information that is especially relevant to a problem-free installation. All information in these instructions is based on the latest product intormation available at the time of publication. MrSteam reserves the right to make changes at any time without notice.

When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS

1. READ & FOLLOW ALL INSTRUCTIONS

2. WARNING Do not permit children under the age of 16 to use this steambath.

3. WARNING Steam is hot and can cause injury or death if improperly used. Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual before installing or using a steam room.

4. WARNING To reduce the risk of injury

   • The wet surfaces of steam enclosures may be slippery. Use care when entering or leaving.

   • The steam head is hot. Do not touch the steamed and avoid the steam near the steam head.

   • Prolonged use of the steam system can raise excessively the internal human body temperature and impair the body’s ability to regulate its internal temperature (hyperthermia). Limit your use of steam to 10-15 minutes until you are certain of your body’s reaction.

   • Excessive temperatures have a high potential for causing fetal damage during the early months of pregnancy. Pregnancy or possibly pregnant women should consult a physician regarding
     correct exposure.

   • Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a steam bath.

   • Persons using medication should consult a physician before using a steambath since some medications may induce drowsiness while other medications may affect heart rate, blood pressure and circulation.

HYPERTHERMIA occurs when the internal temperature of the body reaches a level several degrees above the normnal body temperature of 98.6° F. The symptoms of hyperthermia include an
ncrease in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include:

• Failure to perceive heat;
• Failure to recognize the need to exit the steambath;
• Unawareness of impending risk;
• Fetal damage in pregnant women;
• Physical inability to exit the steambath; and
• Unconsciousness.
  WARNING The use of alcohol, drugs, or medication can greatly increase the risk of hyperthermia.

iSteamAQX Dimensions & Hub Dimensions

Before Installing4

WARNING TO avoid unintentional steambath operation, do not locate the control where other controls, accessories, shower heads, valves, body sprays or similar within the  shower could cause confusion or interfere with the MrSteam control’s intended use and tunction.

CAUTION
To prevent possible injury Do Not use the iSteamAOX control without reading and understanding the MrSteam steam generator Installation and Operation Manual. A peel and stick warning sticker is provided in the MrSteam steam generator Installation, Operation and Maintenance Manual. This manual is provided with every steam generator. The warning sticker must be read and permanently affixed in a conspicuous location near the steam room. Failure to read and affix this warning sticker in a conspicuous location may result in serious injury or death. Please callI MrSteam at 800 767-8326 for a free replacement or it you have any questions regarding the warning sticker.

WARNING
REDUCE THE RISK OF OVERHEATING AND SCALDING

1. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY OR SLEEPY.
   STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING.

2. SUPERVISE CHILDREN AT ALL TIMES.

3. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR HEALTH OR UNDER MEDICAL CARE.

4. BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL DRUGS, OR MEDICATION IS CAPABLE OF CAUSING UNCONScIOUSNESS.

5. DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD.

REDUCE THE RISK OF SLIPPING AND FALL INJURY

1. USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM. FLOOR MAY BE SLIPPERY
   NOTE: FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER’S MANUAL WHICH IS KEP
   THE OWNER’S MANUAL CAN BE FOUND AT WWw.MRSTEAM.COM
   USE OF STEAM ROOM IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL CAN BE DANGEROUS AND CAN RESULT IN INJURY THROUGH SLIP AND FALL OR OTHERWISE.

Not actual size

• If an iSteamAQX control is installed outside the steam room a Remote Temperature Probe (PN MSTS) must be installed inside the steam room per installation instructions supplied with the  Remote Temperature Probe. Failure to install according to instructions will result in inoperative control and overheating of the steam room.
• caution Do not route iSteamAQX control wiring inside conduit together with power lines or close to hot water or steam piping. Doing so may result in an inoperative or hazardous installation. Do not alter or modify any Mr. Steam products including the steam generator or iSteamAOX control. Doing so may result in an inoperative or hazardous installation and will void the warranty.

Care Tips
Use only mild soap and water on a soft cloth to clean the control. Do not use abrasive cleansers.

IMPORTANT NOTES

• The iSteamAQX Control is designed to be flush mounted.
• However, the control may be surface mounted when conditions permit. Consult a MrSteam Customer Service or Technical Service representative to determine it the iSteamAOX control can be surtace mounted. turn power to the steam generator OFF before connecting the control to the generator. Failure to turn the power off will result in an inoperable control.
• Do not operate the iSteamAOX control with other than a MrSteam iSteamAQX compatible steam generator. MrSteam residential steam generators with serial numbers lower than 1174000, or any other brand ot steam generator are not to be operated with iSteamAQX controls. Doing so may result in an inoperative installation. If your generator’s serial number is lower than 1174000 contact MrSteam lechnical Service for upgrade options and components to enable your steam generator to function with iSteamAQx.
• This document contains important safety, operation, and maintenance information. Leave this document with the homeowner. Do not discard this document
• Discontinue use of the steam generator or control it if the steam generator is damaged or otherwise not functioning properly. Doing so may result in an inoperative or hazardous installation
• Refer to the Steambath Generator Installation, Operation and Maintenance Manual for locating and installing the steam head.
  WARNING Do Not alter or modify any Mrsteam products. Doing so may result in an inoperable or hazardous installation and will void the warranty.

Locating the Control

Determine the desired installation location of the control. The iSteamAQX controls are designed to be installed inside or outside the steam room as a matter of personal preference. It the control is installed inside the steam room:

• Locate the control 4-5 feet above the floor near the bather seating area.

• The control teatures an integral temperature sensor. Locate the control in a location representative of the desired steam bathing temperatures. Do not locate the control above or near the steam
  head or direct steam emissions.

• Located the control on a vertical wall.

• The control cable is 30 feet. Insure that the control and steam generator are located accordingly.

IMPORTANT NOTES:

• if required, contact MrSteam to purchase an optional 60′ iSteamAQX control cable part number 104541-60.
• If the control is installed outside the steam room a Remote
• Temperature Probe Part Number MSTS must be installed inside the steam room. Refer to the MSTS installation manual before installing the control.
• Insure MrSteam steam generator is iSteamAQX compatible and has a serial number 1174000 or higher.

IMPORTANT NOTE: The control cable should be run in a dedicated 1″ conduit to facilitate installation and service.

INSTALLER INFORMATION

STEP 1
Make a 1 1/4″ diameter hole in the desired control location.
STEP 1
Route the control cable trom the wall cutout to the Hydtrotouch Hub. Plug in and thread the connector collar into the Hub at the location marked Control.
IMPORTANT NOTE:
The connector is keyed, it will only connect one way.
IMPORTANT NOTE: Be careful not to strain, staple, pinch or otherwise damage the control cable. Route cable as required to permit replacement. Do not route cable inside conduit together with power lines or close to hot water or steam piping Finish the iSteamAOX installation using the instructions on page.

Installation Instructions for iSteamAQX

Step 1.
Mount the hub securely. The hub may be mounted in any orientation.
Plug the 30-foot generator cable into the generator and into the hub.

CAUTION Do not force or twist cable ends together Forcing or twisting cable ends may damage the connectors.
Plug the 30-foot control cable into the hub and into the iSteamAOX.
Thread to connector collars together.

STEP 2
Peel the double stick adhesive off the back of the iSteamAQX control (2a). Apply a bead of silicone around the rear of the iSteamAQX control to create a moisture seal (26). Carefully feed the cables into the rough-in box and secure the control to the wall. Care must be taken to not pinch the cables. Ensure the control is level.

IMPORTANT NOTE:
The control must be installed facing up.

NOTE: The silicone supplied by MrSteam can be used to meet a variety of sealing and gasketing. It cures to silicone rubber and adheres to glass, wood, metal, porcelain, ceramic tile, painted surfaces, many plastics, and rubber.
Surfaces must be clean and dry. Apply a thin layer of product. Fit together and support if necessary. Allow excess material to cure, then trim with a sharp blade. Sealant “skins” in 5 minutes, dries to touch in 1 hour. Fully cures and bonds in 24 hrs.

IMPORTANT NOTE: Do not apply excessive amounts of silicone. Do not apply silicone to any other parts of the control including the adhesive gasket. Insure the mounting surface is clean and dry as required for good adhesion.
Hold the control with the arrow on the screen protector facing up and press the control against the wall until the adhesive sticks and holds firmly. Control may have to be supported or secured until the silicone has cured for 24 hours.

HOMEOWNER SECTION

READ ME FIRST!
WARNING As you follow these instructions, you will notice warning and caution symbols. The blocked intormation is important for the state and efficient installation and operation of this generator. I these are types of potential hazards that may occur during installation and operation:

WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
caution Indicates a potentially hazardous situation, which, it not avoided may result in minor or moderate injury or product damage.

IMPORTANT NOTE: This highlights information that is especially relevant to a problem-free installation. All information in these instructions is based on the latest product information available at the time of publication. MrSteam reserves the right to make changes at any time without notice.

IMPORTANT SAFETY INSTRUCTIONS

1. READ & FOLLOW ALL INSTRUCTIONS 

2. WARNING Do not permit children under the age of 16to use this steambath.

3. WARNING Steam is hot and can cause injury or death if improperly used.
   Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual before installing or using a steam room.

4. WARNING To reduce the risk of injury

   • The wet surfaces of steam enclosures may be slippery. Use care when entering or leaving.

   • The steam head is hot. Do not touch the steam head and avoid the steam near the steam head.

   • Prolonged use of the steam system can raise excessively the internal human body temperature and impair the body’s ability to regulate its internal temperature (hyperthermia). Limit your use of steam to 10-15 minutes until you are certain of your body’s reaction.

   • Excessive temperatures have a high potential for causing fetal damage during the early months of pregnancy. Pregnancy or possibly pregnant women should consult a physician regarding
     correct exposure.

   • Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a steam bath.

   • Persons using medication should consult a physician before using a steambath since some medications may induce drowsiness while other medications may affect heart rate, blood pressure, and circulation.

HYPERTHERMIA occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6° F. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and tainting. The effects of hyperthermia include:

• Failure to perceive heat;
• Failure to recognize the need to exit the steambath;
• Unawareness of impending risk;
• Fetal damage in pregnant women
• Physical inability to exit the steambath; and
• Unconsciousness.
  WARNING The use of alcohol, drugs, or medication can greatly increase the risk of hyperthermia.

WARNING The peel and stick warning label located in the steam bath generator manual is an essential part of providing a safe environment for steam room users. The peel and stick warning label must be applied to the wall of the shower or steam enclosure, at a point that is visible to all users. Failure to install this sticker may result in serious injury or death. The location where this owner’s
manual is kept shall be written in the space provided on the label using permanent ink. For a replacement, warning label contact MrSteam customer service at 1-800-76 STEAM or hello@mrsteam.comn

WARNING
REDUCE THE RISK OF OVERHEATING AND SCALDING

1. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY.
   STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING.

2. SUPERVISE CHILDREN AT ALL TIMES.

3. CHECK WITHA DOCTOR BEFORE USE IF PREGNANT, DIABETIC, OR IN POOR HEALJH OR UNDER MEDICAL CAR

4. BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL, DRUGS, OR MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS. DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD.

REDUCE THE RISK OF SLIPPING AND FALL INJURY

1. USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM. FLOOR MAY BE SLIPPERY
   NOTE: FOR ADDITIONAL SAFETY CONSIDERATIONS SEE THE OWNER ‘S MANUAL WHICH IS KEP:
   THE OWNER’S MANUAL CAN BE FOUND AT WWw.MRSTEAM.COM USE OF STEAM ROOM IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL CAN BE
   DANGEROUS AND CAN RESULT IN INJURY THROUGH SLIP AND FALL OR OTHERWISE.

USER/HOMEOWNER INFORMATION

Turning iSteamAXO On and Of:

• To power the iSteamAQX on, momentarily press the button on the bottom edge.
• To power the iSteamAOX oft, press and hold the button on the bottom edge of the control. Follow the onscreen prompts for power the iSteam AQX off
• Show a picture with arrow pointing to the button.

Care Tips
Use only mild soap and water on a sot cloth to clean the control. Do not use abrasive cleansers.

Safety and Operating Information

WARNING A peel and stick warning sticker is provided in the MrSteam steam generator Installation, Operation and Maintenance Manual. This manual is provided with every steam generator. The warning sticker must be read and permanently affixed in a conspicuous location near the steam room. Failure to read and attic this warning sticker in a conspicuous location may result in ir serious injury or death. Please call MrSteam at 800 7678326 for a tree replacement or if you have any questions regarding the warning sticker.

WARNING Set the steam bathing duration and temperature according to personal preference, however, it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels. Set the duration at 10 minutes max. to gauge comfort and safety
levels. This will allow the steam generator to heat up and
begin producing steam.

CAUTION Do not use any iSteamAOX control without reading and understanding the MrSteam steam generator Installation and Operation Manual (PN 100472). Failure to read and understand these instructions may result in an inoperative or hazardous installation.

CAUTION If an iSteamAQX control is installed outside the steam room a Remote Temperature Probe (PN MSTS) must be installed inside the steam room per installation instructions supplied with the Remote Temperature Probe. Failure to install according to instructions will result in an inopera-tive control and overheating of the steam room.

Warranty

To view or download the MrSteam Control Warranty and register your product go to: blog.mrsteam.com/wr

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interterence to radio or television reception, which can be determined by turning the equipment oft and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

ISED Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS-102 and compliance with RSS-102
RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
www.mrsteam.com
Products, information, and specifications are subject to change without notice.
Please call Technical Support at 1.800.76.STEAM (East Coast) or 1.800.72.STEAM (West Coast) for more information.

NOTICE The model and serial number is printed on the data plate on the front of the steam bath generator.
Have this information available when contacting Technical Service.

2U20 Mrsteam and des., A Lifetime of Pleasure, Girl emp0, AromaFlo, AudioWizard, AutoFlush, Autosteam, Butier Package, Chromasteam, lean Steam..Every lime, Club Therapy, Cl Day pa,
Digital 1, Express Steam, Feel Good Inc., From Bathroom to Spa, HomeWizard, iButler, genie, iSpa Package, iSteam, tempo, tempo/Plus, Linear Steamhead, Making Wellness a Way of Lite,
Music Therapy, My Steam, SmartSizing, Spa Package, Steam Genie, Steam on Demand, Steam in a Box, Steam@Home, SteamStart, SteamIherapy, MrSteam, Tala, Tala Bath & Body, Tempo, The
Intelligent Steambath, Valet Package, and Virtual Spa System have registered trademarks of MrSteam.
PUR 100543 REV 2

References

• MrSteam Warranty Registration
• Home | Steam Shower Generators Controls Accessories | MrSteam

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>