PLAY STEAM RC Robot Snake Learning Booklet User Guide
- October 27, 2023
- PLAY STEAM
Table of Contents
PLAY READ INSPIRE
THE LEARNING BOOKLET
— RC ROBOT SNAKE —
Aad CO Xe
EASY TO ASSEMBLE
HOURS OF FUN.
RC Robot Snake Learning Booklet
WARNING MESSAGE
**WARNING MESSAGE
**
GENERAL WARNING
Before you begin, please read through the instructions together with your
children. Make sure you understand the safety messages. Please keep the
packaging and instructions, as they contain important information.
Not suitable for children under 3 years. Small parts.Small ball.
Choking hazard. Children should have parental supervision when assembling the
product.
Water and rain will damage the electronic components.
Please clean the product with a clean cloth when necessary.
Make sure to remove the batteries from the battery compartment before
cleaning.
This toy produces flashes that may trigger epilepsy in sensitized individuals.
Heating parts – Do not touch.
Using a screwdriver
You must always be supervised by an adult when using a screwdriver.
The metal may have sharp edges that can cause injury.
Using batteries
– Do not charge non-rechargeable batteries;
– Do not mix different types of batteries or new and used batteries;
– Insert batteries with correct polarities;
– Remove exhausted batteries from the toy;
– Do not short-circuit supply terminals;
– Remove rechargeable batteries from the toy before charging;
– Charge rechargeable batteries under adult supervision only.
– Do not use rechargeable batteries.
Cement floors may wear out the wheels quickly.
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that maycause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment offand on, the user is Tencouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit difierent from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
PACKAGE CONTENTS
| Serial | Name | Quantity | Serial | Name | Quantity |
|---|---|---|---|---|---|
| 1 | Snake Head | 1 | 7 | Snake Body Base | 5 |
| 2 | Battery Section | 1 | 8 | Ball | 1 |
| 3 | Snake Tail Base | 1 | 9 | Ball Pusher | 1 |
| 4 | Battery Section Cover | 1 | 10 | Pulley | 14 |
| 5 | Snake Tail Cover | 1 | 11 | Latches | 7 |
| 6 | Snake Body Cover | 5 | 12 | Remote Control | 1 |
Necessaey but not included
INSTALLATION
-
Connect the two sections using a latch and pass the rnotor port wire from the snake head through the latch. Then snap the pulleys into the slots on the base.
-
Plug the motor port in the power port from the battery section. Note that the triangles on the ports are on the same side.
-
Op. the battery compartments on battery section and remote control, install 2 AAA batteries in each according to the polarity sign, then close the compartments.
-
Test the snake. Tum the switch at the bottorn of the snake on, the power light on the snake head will start flashing.
-
Tum the remote control to Level 1 or 2 (the power light will turn on). Press the right and left buttons. The snake head will start to glide around.
-
Push each pulley into the pulley shaft buckles on the snake body base and the snake tail base.
-
Connect all snake bodies and the snake tail using latches. Put on the battery section ‘ cover, note that it has 2 arrow on the top.
-
Buckle the snake body and tail covers to their corresponding bases, then insert the ball pusher to the bottom of the snake head base.
Assembly complete!
Controllin the Snake
Before you start, make sure the batteries are installed and the compartments
on the snake and the remote control are properly screwed.
Glide forward
You can start with gliding forward. Push the two buttons on the remote
together, the snake will go straight forward.
Glide like a snake
Since the left and right buttons control left and right tuming, if you push
the two buttons altematively, you will see the snake travels in “S” shape. It
takes sorne practice to master your controlling skill. Take your time and play
a prank on your fellows!
Note: Some surfaces like thick carpet or lawn may interrupt the snake, try to avoid them when playing.
ACTIVITIES
Do you know what BIONIC means?
Bionics or “biologically inspired engineering” is the science of creating
engineering systems inspired by nature.
The robot you have in your hands has a body inspired by snakes. As you may
know, snakes, like many other aquatic and semi-aquatic animals, slither.
They have a flexible body that allows them to slither very fast. be as agile
as a snake, your snake robot has a body composed of several parts assembled
together, giving an irnpression of flexibility.
Train your Snake on free-kicks
You can train your snake to take free-kicks.
You first need goals. You can follow the steps on the next page to make your
own goal frame with a simple sheet of paper. Place the ball at a certain
distance from the snake, with the snake facing it. Then, imagining the whistle
signal, press the remote controllers to make your snake move forward and hit
the ball.
Shape your goal frame
Take a sheet of paper. Follow the three sirnple steps on the figure, folding
along the dotted line (you can draw these lines on your paper to be more
precise).
Then unfold the paper and repeat the sarne steps on the other half of the
sheet. Your sheet of paper should look like figure A. Fold the paper to shape
your goal frarne.
2. Find your best option
you will notice that depending on where you hit the ball, the trajectory will
not be same.
The pusher on the snake is designed to ease the control of the ball. In order
to make the free-kicks easier you can apply a strip of paper as illustrated.
Try with and without the strip of paper and choose the best option for you.
In any case, to be able to take very good free kicks you will have to train
your snake for a little while.
Read to be inspired
What else can the bionic snake do?
There is a kind of robotic snake that can work underwater for construction and
investigation tasks.
**** Read to be inspired
What else can the bionic snake do?
There is a kind of robotic snake used for rescuing because of its flexible and
durable body.
Read to be inspired
Fun Fact!
There is a soccer skill called SNAKE, also known as Flip Flap. It is a
dribbling skill used for fooling defensive players.
Players move the ball in a direction they do not want to go.
PLAYSTEM.COM
©2017 DESIGNED BY PLAYSTEM EDUCATION LIMITED, LONDON.
WEBSITE: WWW.PLAYSTEM.COM
EMAIL: INFO@PLAYSTEM.COM
ADDRESS: SUITE 35 – 36 THE DESIGNWORKS,
PARK PARADE, LONDON, NW10 4HT. MANUFACTURED BY HANGZHOU ZT
MODEL COMPANY LIMITED. ADDRESS: NO 6
MINGDE RD., PUYAN, BINJIANG, HANGZHOU, CHINA.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>