Rhine 7250T Remote Control User Guide
- June 15, 2024
- Rhine
Table of Contents
Rhine 7250T Remote Control
Specifications
- Battery: CR2032 3V (1 PCS.)
- Operating Controls: 24bit code combinations
Product Usage Instructions
Setting up the Operating Controls:
- Ensure that the unit is powered by a CR2032 3V battery (not included).
- To prevent battery leakage, remove the battery when the unit is not in use.
- Store the controller away from excess heat or humidity.
- Avoid interference from or to other remote units such as garage door openers, car alarms, or security systems.
Using the Operation Buttons:
- Key – For BOTTOM LIGHT ON/OFF
- For FAN ON/OFF control
Battery Replacement:
- Turn the tool counterclockwise to open the rear battery cover.
- Remove the old battery and insert a new CR2032 3V battery with the cut part facing down.
- Put back the battery cover and lock it clockwise with a tool to complete the battery replacement.
Warning: Keep batteries away from children. See Manual for more details.
General Information:
This remote controller is designed to separately control your ceiling fan
speed and light brightness.
Installation and Operation of Fan Speed Controller:
Setup for Ceiling Fan Controller:
- Turn off the power.
- Press any button on the controller until no LED display is showing to ensure the electricity is entirely released.
- Turn on the power.
- Press the FAN OFF button for more than 3 seconds. The ceiling fan controller will have 2 blinks, indicating a successful setup.
- You can now start controlling the ceiling fan light and fan speed.
Notice: Any changes or modifications not expressly approved by the responsible party may void the user’s authority to operate the equipment.
Important Note: To comply with FCC RF exposure compliance requirements, no changes to the antenna or device are permitted. Any such changes may result in the device exceeding RF exposure requirements and void the user’s authority to operate the device.
Federal Communications Commission Interference Statement:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a different circuit from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
Frequently Asked Questions (FAQ):
- Q: What type of battery does this unit use?
- A: This unit operates on a CR2032 3V battery (1 PCS.), which is not included.
- Q: How do I replace the battery?
- A: Turn the tool counterclockwise to open the rear battery cover, remove the old battery, insert a new CR2032 3V battery with the cut part facing down, put back the battery cover, and lock it clockwise with a tool to complete the battery replacement. Make sure to follow the warning slogans engraved on the back of the shell and keep batteries away from children.
INSTRUCTIONS FOR OPERATION
SETING THE OPERATING CONTROLS
- This unit operates on CR2032*1 PCS.; 3 volts battery (not included). To prevent possible damage if the battery should leak, be sure to remove the battery when the unit is not use.
- Store the controller away from excess heat or humidity.
- This remote-control unit is required with 24bit code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm or security system.
- Operation buttons on the panel of transmitter.
GENERAL INFORMATION
This remote controller is designed to separately control your ceiling fan speed and light brightness.
INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER
Setup for ceiling fan controller
- Turn off the power. (In order to make sure the electricity is entirely released, please press any button on the controller till no LED display showing)
- Turn on the power
- Press the FAN OFF button for more than 3 sec. The ceiling fan controller will have 2 blinks. It means the setup is successful. You could start to control the ceiling fan light and fan speed.
NOTICE:
The changes or modifications not expressly approved by the party responsible
for compliance could void user’s authority to operate the equipment.
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void
user’s authority to operate the device.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAUTION : Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause
Canada, Industry Canada (IC)
Notices
This device complies with Canada license‐exempt RSS standard(s). Operation is
subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada
(IC)radio frequency exposure limits. The Wireless Device should be used in
such a manner such that the potential for human contact during normal
operation is minimized. This device has also been evaluated and shown
compliant with the IC RF Exposure limits under portable exposure conditions.
Information concernant
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>