Rhine UC7261T9 Ceiling Fan Remote Control Kit Instructions

UC7261T9 Ceiling Fan Remote Control Kit

Product Information

The remote-control unit requires two AAA batteries with 3 volts capacity (not included). It is recommended to remove the batteries when the unit is not in use to prevent damage in case of leakage. The controller should be stored away from excess heat or humidity to ensure proper functioning. The remote-control unit uses 35bit code combinations to prevent interference from or to other remote units, such as garage door openers, car alarms, or security systems.

FCC Compliance

To comply with FCC RF exposure compliance requirements, no changes to the antenna or device are permitted. Any modifications can result in the device exceeding RF exposure requirements and void the user’s authority to operate the equipment.

Canada License-Exempt RSS Standard

This device complies with Canada license-exempt RSS standard(s). It must not cause interference and must accept any interference that may cause undesired operation of the device.

Product Usage Instructions

1. Insert two AAA batteries into the remote-control unit.
2. Ensure that the batteries are correctly placed and have enough charge.
3. Point the remote-control unit towards the device to be controlled.
4. Press the appropriate button on the transmitter panel to operate the device.
5. After use, store the remote-control unit away from excess heat or humidity and remove the batteries to prevent damage if there is a battery leak.

Note: Any changes or modifications not approved by the grantee can void the user’s authority to operate the equipment. Always refer to the user manual for specific instructions and guidelines.

INSTRUCTIONS FOR OPERATION

SETING THE OPERATING CONTROLS

1. This unit operates on AAA*2PCS.; 3 volts battery (not included). To prevent possible damage if the battery should leak, be sure to remove the battery when the unit is not use.
2. Store the controller away from excess heat or humidity.
3. This remote-control unit is required with 35bit code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm or security system.
4. Operation buttons on the panel of transmitter.

GENERAL INFORMATION

This remote controller is designed to separately control your ceiling fan speed and light brightness.

INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER

Setup for ceiling fan controller

1. Turn off the power. (In order to make sure the electricity is entirely released, please press any button on the controller till no LED display showing)
2. Turn on the power
3. Press the FAN OFF button for more than 3 sec. The ceiling fan controller will have 2 blinks. It means the setup is successful. You could start to control the ceiling fan light and fan speed.

NOTICE: The changes or modifications not expressly approved by the party responsible for compliance could void user’’’’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’’’’s authority to operate the device.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>