CAME C005 Chain Transmission System For Sectional Doors Instruction Manual
- June 15, 2024
- CAME
Table of Contents
CAME C005 Chain Transmission System For Sectional Doors
Specifications
- Product Name: IT Chain Transmission System for Sectional Doors
- Model Number: 119CT66
- Version: 1.0
- Date: 01/2011
Components:
- Chain with joint
- Mounting bracket
- Shaft with pinion Z26
- Linguette A (for hollow shaft) or Linguette B (for solid shaft)
- Crown Z40
- Washer UNI6593 8 x 24
- Screw UNI5739 M8 x 16
- Screw UNI5933 M6 x 16
- Fan-shaped washer
MOUNTING:
- Depending on the type of door shaft, insert either Linguette A or Linguette B.
- Insert the Z40 crown onto the spring rod and secure it using the nut.
- Insert Linguette A into the pinion shaft.
- Insert the shaft into the motor and fasten it using the screw, washer, and nut.
- Fasten the mounting bracket to the gearmotor using the screws.
- Join the two ends of the chain using the clasp and hook it to the crown of the door shaft.
- Release the gearmotor by turning the rod clockwise.
- Position and fasten the gearmotor to the wall after hooking the chain to the pinion shaft (fastening will depend on the type of wall).
WARNING: The crown and pinion must be perpendicularly aligned.
Dismantling and Disposal:
Before proceeding, check your local legislation on the matter. The components of the packaging (i.e. cardboard, plastic, etc.) are solid urban waste and can be disposed of by separating them for recycling. Other components (i.e. control boards, transmitter batteries, etc.) may contain hazardous substances. These must be handed over to specially authorized disposal firms. DO NOT DISPOSE OF IN NATURE!
Disclaimer:
The data and information in this manual may be changed at any time and without prior notice.
COMPONENTS
- Chain with clasp
- Fastening bracket
- Shaft with Z26 pinion
- Bar A, for hollow shaft
- B, for solid shaft Bar
- Z40 crown
- Washer
- UNI6592 Ø6 washer 8 X 24
- UNI5739 M8 x 16 hexagonal screw
- UNI5933 M6 x 16 counter-sunk head screw
- Lock washer
MOUNTING
- Depending on the type of door B, insert 1 either bar A 3 or bar B 4 insert the Z40 crown to the spring rod 2 and secure it using the nut LA).
- Inset bar A 3| into the pinion shaft 5; insert the shaft into the motor 6 and fasten it using the screw, washer and nut 7 C
- Fasten the bracket to the gearmotor using the screws D
- Join the two ends of the chain 9 using the clasp 10 and hook it to the crown of the door shaft 8 E
- Release the gearmotor by turning the rod clockwise 12.
- Position and fasten the gearmotor to the wall after hooking the chain to the pinion shaft 11 F (fastening will depend on the type of wall).|
WARNING: the crown and pinion must by perpendicularly aligned..
Dismantling and disposal – Before proceeding it is always a good idea to check your local legislation on the matter. The components of the packaging (i.e. cardboard, plastic, etc.) are solid urban waste and may be disposed of without much trouble, simply by separating them for recycling. Other components (i.e. control boards, transmitter batteries, etc.) may contain hazardous substances. These must therefore be handed over the specially authorised disposal fi rms. DO NOT DISPOSE OF IN NATURE! The data and information in this manual may be changed at any time and without prior notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>