URBAN 110040-32 Bicycle Kids Helmet User Guide
- June 15, 2024
- Urban
Table of Contents
110040-32 Bicycle Kids Helmet
User Guide
110040-32 Bicycle Kids Helmet
UK
Instruction manual
Bicycle helmet, Kids
Green with robots, 47-53 cm
PANTONE 2915C 2014.02.26 WS-0579
Item no.: 110040-32
Barcode: 5705532089794
This helmet is certified according to the following standard:
- (EU) 2016/425: Guidelines for personal protection equipment
- EN 1078:2012 + A1:2012 – European standard for cyclists, skate boarders and inline skaters
- Certified by: SGS FIMKO OY, P.O. Box 30 (Särkiniementie 3), 00211 Helsinki Finland, notified body No. 0598
- Declaration of Conformity: www.csi-bike.com
EN 1078:2012+A1:2012
Attention: Please note that no helmet is indestructible and will not
prevent all head injuries.
For the best possible protection, please observe the following guidelines:
Usage
This helmet is recommended as protective equipment for the following activities. It is not suitable for the following activities: Warning! Please note that it is necessary for children to remove their helmets before entering playgrounds. This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child gets trapped with the helmet.
Optimum fit
- Please try various sizes for comfort and security, ensuring that the helmet sits horizontally on your head.
- Do not pull the helmet over your forehead, reducing visibility.
- Do not push the helmet towards the back of your head, as this will not protect your forehead.
The helmet can only protect your head if it fi ts correctly.
Adjustment of the head ring
Adjusting the helmet to the individual head size can be achieved, depending on
the type, with the following easy to use fitting systems.
Adjust the rear adjusting wheel for the circumference of the head such that
the FIT SYSTEM helmet fits flush and is comfortable (figure 3).
Adjustment of the straps
When wearing the helmet for the first time, please adjust the straps so that
they meet tautly and comfortably beneath the ears. The easily adjustable
triangular locks on both sides help you in doing so. Make sure the chin-guard,
which must be locked before every ride, doesn’t lie on the jaw-bone.
If
you choose to cut the chinstrap, leave a protrusion of approx. 2 inches or 4
cm above the lock. Heat the cut ends carefully to prevent the webbing from
unravelling. Be careful with high heat near the helmet because the strap and
helmet are flammable. Be careful to avoid contact with melted nylon. Run the
chinstrap through the lock as noted below and use the “O-Ring” to secure any
excess strapping. 
Proper maintenance and care
- Regularly check the helmet for signs of damage.
- Do not alter the specification of this helmet as it will reduce its protective effect.
- Only use original spare parts.
- Do not apply stickers or paint to the helmet as this can be damaging to the materials.
- Do not remodel or misuse the helmet.
- Do not expose the helmet to temperatures in excess of 60˚C. Do not store behind glass, e.g. in a car (burning glass effect), near heaters etc.
- If you suspect that the helmet has received a large impact, even if there is no visible damage, please purchase a new helmet.
- This helmet has a limited life time and must be replaced 5 years after the first time it is used, and at most after 8 years from it’s productions date, even if it displays no clear visible or technical defects.
- The helmet, inner pads and head ring can be cleaned using lukewarm water, solvent-free detergents and a soft cloth.
Made in PRC . CSI A/S . Egeskovvej 15A
DK-8700 Horsens . www.csi-bike.com
CSI_MA_ST5_UK_001 . Nov2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>