MOHAWK EV4N1-5515A Vinyl 4 in 1 Floor Moulding Instruction Manual
- June 15, 2024
- MOHAWK
Table of Contents
MOHAWK EV4N1-5515A Vinyl 4 in 1 Floor Moulding
Product Information
The Mohawk multifunctional 4-in-1 molding is a versatile transition molding that allows you to create four different applications. It is designed to provide smooth transitions between different types of flooring and can be used in various settings such as doorways, walls, fireplace hearths, and sliding glass doors.
Specifications
- Flooring Thickness:
- 2mm – 3mm
- 4mm – 5mm
- 5mm – 6mm
- 7mm – 8mm
- 3mm – 5mm
- 6mm – 7mm
Product Usage Instructions
T-Molding
The T-molding is used to transition between flooring of equal heights and in doorways.
- Remove carpet/end molding transition support from track with a utility knife.
- Leave a 1-1/2 inch space between the two surfaces to be joined.
- Separate the shims into two separate pieces of even widths where folded. Use a utility knife if needed. Note: The universal shim is provided in one single piece. After separating, follow the specific diagrams in these instructions for shim assembly with your flooring height.
- If installing as a T-Molding or Hard Surface Reducer only, remove the narrow portion of each of the two shim pieces. Do not remove this piece if installing as carpet transition or end molding.
- Measure the area where the molding will be installed. Transfer measurements to the molding cover, shims, and track, and trim to fit.
- Line up the cover with the track. Start at one end and use a rubber mallet to tap the track and cover together. Push down firmly onto the track, working from one end to the other.
Carpet Transition
The carpet transition provides a smooth transition between your hard surface floor and carpet.
- Remove carpet/end molding transition support from track with a utility knife.
- Leave a 1-1/2 inch space between the two surfaces to be joined.
- Separate the shims into two separate pieces of even widths where folded. Use a utility knife if needed. Note: The universal shim is provided in one single piece. After separating, follow the specific diagrams in these instructions for shim assembly with your flooring height.
- Measure the area where the molding will be installed. Transfer measurements to the molding cover, shims, and track, and trim to fit.
- Line up the cover with the track. Start at one end and use a rubber mallet to tap the track and cover together. Push down firmly onto the track, working from one end to the other.
Hard Surface Reducer
The hard surface reducer connects two floors of different heights.
- Remove carpet/end molding transition support from track with a utility knife.
- Leave a 1-1/2 inch space between the two surfaces to be joined.
- Separate the shims into two separate pieces of even widths where folded. Use a utility knife if needed. Note: The universal shim is provided in one single piece. After separating, follow the specific diagrams in these instructions for shim assembly with your flooring height.
- If installing as a T-Molding or Hard Surface Reducer only, remove the narrow portion of each of the two shim pieces. Do not remove this piece if installing as carpet transition or end molding.
- Measure the area where the molding will be installed. Transfer measurements to the molding cover, shims, and track, and trim to fit.
- Line up the cover with the track. Start at one end and use a rubber mallet to tap the track and cover together. Push down firmly onto the track, working from one end to the other.
FAQ
Q: What is the purpose of the shims?
The shims provided with the 4-in-1 molding are used to adjust the height and
alignment of the molding based on the thickness of your flooring. They ensure
a proper fit and smooth transition.
Q: Can I use the 4-in-1 molding for different flooring thicknesses?
Yes, the 4-in-1 molding is designed to accommodate different flooring
thicknesses. Refer to the specifications section for the recommended flooring
thickness ranges.
Q: Can I install the 4-in-1 molding myself?
Yes, you can install the 4-in-1 molding yourself by following the provided
instructions. However, if you are unsure or uncomfortable with the
installation process, it is recommended to seek professional assistance.
Q: Can I use the 4-in-1 molding in wet areas such as bathrooms?
No, the 4-in-1 molding is not recommended for use in wet areas or areas with
excessive moisture. It is best suited for dry indoor environments.
The Mohawk multifunctional 4-in-1 molding allows you to utilize a single transition to create four different applications.
Please DO NOT discard the shims. Refer to the instructions for the specific
profile you are installing for details on how to use the shims.
Refer to the installation instructions provided by the flooring manufacturer
for required expansion spaces.
REVIEW INSTALLATION CHECKLIST
- Inspect the moulding cover and track. Ensure that the channel on the moulding cover is uniform in width along the entire length.
- Do not push parts into track until ready to install in final position.
- Do not remove from track once installed.
- Use a new 60–120 fine-tooth finishing saw blade for flooring for best cutting results.
- Use tin snips or a heavy duty cutting tool to cut the track and shims.
- Depending on moulding type, all parts may NOT be used.
- Always install screws in end holes of track and then every other hole.
- For concrete floors, drill hole using 3⁄16” (5mm) diameter concrete drill bit, insert plastic anchor, then use screw.
- Depending on the floor height, attach the shims or track directly to the subfloor (remove any padding or underlayment).
- This product has been finished for you; do not sand or paint.
CHOOSE YOUR TRANSITION TYPE
The kit allows assembly of four different molding options from one single product.
-
Carpet Transition
The carpet transition provides a smooth transition between your hard surface floor and carpet. -
T-molding
The T-molding is used to transition between flooring of equal heights and in doorways. -
End Molding
The end molding can be used to finish flooring where it meets vertical surfaces such as walls, fireplace hearths and sliding glass doors. -
Hard Surface Reducer
The hard surface reducer connects two floors of different heights.
INSTALL YOUR MOLDINGS
Each individual package includes the following:
-
Leave a 1-1/2” space between the two surfaces to be joined.
-
Separate the shims into two separate pieces of even widths where folded. Use a utility knife if needed.
NOTE: The universal shim is provided in one single piece. After separating, follow the specific diagrams in these instructions for shim assembly with your flooring height.
-
If installing as a T-Moulding or Hard Surface Reducer only, remove the narrow portion of each of the two shim pieces. DO NOT remove this piece if installing as carpet transition or end moulding.
-
Measure the area where the moulding will be installed. Transfer measurements to the moulding cover, shims and track and trim to fit.
-
Using proper shim configuration as outlined, begin install of shims and track. Using a polyurethane glue, place a bead of glue between the subfloor and bottom shim, between the shims (if needed for configuration), and between the top shim and track.
Ensure that excess glue is not used so that floating floor cannot bind to track. Once glue is applied with track and shim(s) in place,fasten the shims and track to the subfloor using wood screws or ring shank nails.
If installing onto concrete subfloor, drill anchor holes using a 3/16” diameter concrete drill bit, and utilize concrete anchors and screws. With shim and track fastened, you are now able to install the transition cover onto the track. -
Line up cover with track. Start at one end and use a rubber mallet to tap the track and cover together. Push down firmly onto track, working from one end to the other.
T-MOLDING
The T-molding is used to transition between flooring of equal heights and in
doorways.
- Remove carpet/end molding transition support from track with utility knife.
CARPET TRANSITION
The carpet transition provides a smooth transition between your hard surface
floor and carpet.
HARD SURFACE REDUCER
The hard surface reducer connects two floors of different heights.
- Remove carpet/end molding transition support from track with utility knife.
END MOLDING
The end molding can be used to finish flooring where it meets vertical
surfaces such as walls, fireplace hearths and sliding glass doors.
MOHAWK TECHNICAL SERVICES DEPARTMENT
196 S. INDUSTRIAL BLVD. CALHOUN, GA 30701
888-387-9881
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>