Fuairmee HMT-2 Greenhouse Heater with Digital Thermostat User Manual

Fuairmee HMT-2 Greenhouse Heater with Digital Thermostat

Temperature Controller HMT-2

Technical Specifications

• Works great for controlling plants or pet heat mats temperature.
• Dual display window, be able to display measured temperature and set temperature at the same time.
• Accurate LED display in 1 degree increments.
• Max load: 3000W(230V)/ 2000W(120V)
• Max Amps: 16A
• 230V Input & output voltage
• Support reading with Centigrade or Fahrenheit unit
• Saves current program after powering off
• Includes power and load indicator lights

Specifications

• Temperature setting Range
• Temperature display range
• Temperature Accuracy
• Temperature Control Mode
• Input Power(EU Plug)
• Temperature Control Output(EU Plug)
• Input Power(US Plug)
• Temperature Control Output(US Plug)
• Buzzer Alarm
• Sensor Length
• Input Power Cable Length
• Output Power Cable Length

Set Up the Thermostat

1. Insert the probe approximately 1-1.5 inches (2.5-4cm) into the testing area.
2. Position the thermostat up. Do not submerge the thermostat.
3. Plug the cooling/heating equipment into the thermostat.
4. Plug the thermostat’s power cord into the power source/electrical outlet. The POWER LED lights up.
5. Set the maximum desired temperature for the cooling/heating equipment.

Using the Controller

WARNING: DO NOT IMMERSE CONTROLLER IN WATER

FAQ

Q: Can I use this temperature controller for both plants and pets?
A: Yes, the HMT-2 temperature controller is suitable for controlling the temperature of both plants and pet heat mats.

Q: What is the maximum load and amps supported by this temperature controller?
A: The HMT-2 temperature controller can handle a maximum load of 3000W (230V)/2000W (120V) and has a maximum amp rating of 16A.

Q: Can I switch between Centigrade and Fahrenheit units for temperature readings?
A: Yes, this temperature controller supports reading temperatures in both Centigrade and Fahrenheit units. You can choose your preferred unit.

Q: Does the temperature controller save the current program after powering off?
A: Yes, the HMT-2 temperature controller saves the current program even after powering off, ensuring that your desired settings are retained.

TECHNICAL SPECIFICATIONS

• Works great for controlling plants or pet heat mats temperature.
• Dual display window, be able to display measured temperature and set temperature at the same time
• Accurate LED display in 1 degree increments.
• Max load:3000W(230V)/ 2000W(120V)
• Max Amps:16A
• 230V Input & output voltage Support reading with Centigrade or Fahrenheit unit;
• Saves current program after powering off
• Includes power and load indicator lights

Specification

SET UP THE THERMOSTAT

1. Insert the probe approximately 1”-1.5”(2.5-4cm) into the testing area.
2. Position the thermostat up. Do not submerge the thermostat.
3. Plug the cooling/ heating equipment into the thermostat.
4. Plug the thermostats’ power cord into the power source/electrical outlet. The POWER LED lights up.
5. Set the maximum desired temperature for the cooling/ heating equipment.

USING THE CONTROLLER

1. Press the SET button to display the current pre-set temperature. The thermostat’s LED screen shows the current temperature whenever the SET button is not activated.

2. Press and hold the SET button for three seconds to enter temperature setting mode.
   Press the ▲(UP) or ▼(DOWN) button to adjust the temperature. The LED screen shows the numbers as you cycle through them. Press the SET button again to set the chosen temperature.

3. HEATING/COOLING MODE: Press and hold the ▲(UP) button for three seconds to switch heating/ cooling mode. The MODE LED lights red when setting in heating mode. And the MODE LED lights green when setting in cooling mode.

4. HEATING MODE: When the measured temperature≤ the setting temperature, the heating indicator light will on, and heating relay starts to work; when the measured temperature ≥ the setting temperature, the heating indicator light will off, and heating relay stops working.

5. COOLING MODE: When the measured temperature the setting temperature, the cooling indicator light will on, and refrigeration relay starts to work; when the measured temperature ≤ the setting temperature, the cooling indicator light will off, and the refrigeration relay stops working.

6. Press the ▲(UP) button for to display the temperature in Celsius. Press the ▼(DOWN) button for to display the temperature in Fahrenheit.

WARNING: DO NOT IMMERSE CONTROLLER IN WATER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>