WAGNER 2362049 Spray Attachment Wood Metal Extra Detail User Manual

2362049 Spray Attachment Wood Metal Extra Detail

WOOD &METAL EXTRA DETAIL

Detail spray attachment

Before using the attachment, read these operating instructions and familiarise yourself with the operating instructions for the basic unit. Keep the operating instructions in a safe place. The safety instructions for the basic unit apply to  this Detail spray attachment.
General instruction
The Detail spray attachment was developed for applying water-soluble paints and lacquers as well as paints and lacquers containing solvents.
Thanks to its particularly fine spray jet the attachment allows direct paint application and thus the coating of thin, small and filigree objects. It is excellently suitable for detailed and creative work.
The special form of the 250-ml container makes it possible to mix small quantities of valuable paint and to spray the paint without residues.
CAUTION! • The units may only be used with a functional valve. If paints rises in the ventilating hose (Fig. 1 A, item 12) do not operate the unit further!
Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary.

• Do not place the spray gun on the side.
• Do not combine components from different spray attachments.
  The parts could be damaged.

Description (Fig. 1)

1. Gun body	2) Needle

2. Nozzle seal| 4) Nozzle
3. Air cap| 6) Union nut
4. Material quantity regulation| 8) Trigger
5. Container seal| 10) Feed tube
6. Container| 12) Ventilating hose
7. Valve cover| 14) Diaphragm
8. O-ring| 16) Viscosity test cup

Preparation of the Coating Material
The paints usually need to be diluted for use with the spray gun. The Detail spray attachment can be used to process coating materials up to a maximum flow time (viscosity) of 30 seconds.
Measuring the Viscosity (Fig. 2)

1. Stir the coating material thoroughly before measuring.
2. Dip the viscosity test cup (16) completely into the coating material.
3. Hold the test cup up and measure the time in seconds until the liquid empties out.
   Compare the measured “runout time” with the Viscosity Table.

Detail spray attachment

Viscosity Table

630 W
Thinner-soluble primers| max.30| max.30| max.30| max.30
Thinner-soluble varnishes| max.30| max.30| max.30| max.30
Water-soluble primers| max.30| max.30| max.30| max.30
Water-soluble varnishes| max.25| max.30| max.30| max.30
Wood preservatives, strippers, oils| undiluted
Disinfectants, plant protectants| undiluted
Automobile spray paint| max.25| max.30| max.30| max.30

Adjusting the material quantity
Very small quantities can be processed with this attachment. To prevent paint runs on the object, first adjust the paint quantity by spraying onto a piece of card or paper from the same spraying distance.
First turn the adjustment knob (Fig. 1, Item 7) fully to the left (-) and then slowly increase the material quantity to the desired amount by turning it to the right (+).
For further information on setting the spray pattern and the correct spraying technique refer to the instructions of the basic device.
Spraying technique
With the Detail spray attachment extremely fine free hand lines can be sprayed for creative at small distances and using small amounts of material. If you stick a self-made template to the object, sharp edges result and you can spray the  paint directly on without great losses. In order no to blow away small objects during the coating process, we recommend fastening the object with a clip or double-sided adhesive tape (not included in the scope of delivery).
Further information on the spraying technique can be found in the instructions for the basic device.

Interruption of Work
When processing 2-component varnishes, clean the device immediately.

Shutting down and cleaning
Please also refer to the instructions of the basic device.

1. Switch the unit off. Vent the container in case of longer breaks and after the work has been terminated. This can be done by briefly turning open and then closing the container or by pulling the trigger guard and letting the paint into  the original paint container.

2. Screw of the container and empty it. Pull out the suction tube with container seal.

3. Preclean the container and feed tube with a brush. Clean the ventilating bore (Fig. 1, C).
   CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects.
   The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe.

4. Pull the ventilating hose (Fig. 1 A, 12) at the top from the gun body. Screw off the valve cover (13). Remove the diaphragm (14). Clean all the parts carefully.

5. Unscrew the union nut and remove the air cap and nozzle. Clean the air cap, nozzle seal and nozzle with a brush and solvent or water.

Assembly
The unit may only be operated with an integer diaphragm (Fig. 1A, 14).

1. Place the diaphragm (Fig. 1A, 14) with the pin facing upwards on the bottom section of the valve. Also see the marking on the gun body.
2. Place on the valve cover (Fig. 1A, 13) and screw it closed.
3. Place the ventilating hose (Fig. 1A, 12) on the valve cover and on the nipple at the gun body.
4. Push the nozzle seal (Fig. 1B, 3) over the needle (2); the groove (slot) should point towards you.
5. Put the nozzle (Fig. 1B, 4) onto the gun body and find the correct position by turning it.
6. Put the air cap (Fig. 1, 5) onto the nozzle (4) and tighten it using the union nut (6).
7. Place the container seal from below on the suction tube and slide it over the collar, while turning the container seal slightly.
8. Insert the suction tube with container seal in the gun body.

Spare Parts List (Fig. 1)

AUS (2361 988)
6| Union nut| 2362873
9| Container seal| 2323039
10| Feed tube| 2362935
11| Container 250 ml with cover| 417922
12,13,14| Ventilating hose, Valve cover, Diaphragm| 2304027
15| 0-Ring| 2362875
16| Viscosity test cup| 209058

The CLICK&PAINT SYSTEM with additional spray attachments and accessories off ers the right tool for each work.
Further information about the WAGNER range of products for renovating is available under www.wagner-group.com
Environmental protection
The appliance and accessories should be recycled in an environmentally friendly way. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtain  information from a specialist retailer.
Important Note regarding Product Liability!
Using other accessories and spare parts can lead to partial or total loss of liability and guarantee claims. With original WAGNER accessories and spare parts, you have the guarantee that all safety regulations are fulfi lled.

2 years guarantee

The guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or freeof-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale.

WAGNER SPRAYTECH UK LTD
Opus Park
Moorfield Road
GB-Guildford Surrey GU1 1SZ
T +44 (0) 1483 – 454666
F + 44 (0) 1483 – 454548
Part. No. 2362049
10/2015_RS
© Copyright by J.Wagner GmbH

References

• Group Publishing
• WAGNER Group for industry, craftsmen & do-it-yourselfers | WAGNER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>