Panasonic ER1421/ER1411 AC/Rechargeable Professional Hair Clipper User Manual

: June 4, 2024
: Panasonic

Table of Contents

Important
Speciﬁcations
Parts identiﬁcation
Charging the hair clipper
Blade maintenance
Lubrication
Documents / Resources

Operating Instructions
AC/Rechargeable Professional Hair Clipper
Model No. ER1421/ER1411

Before operating this unit, please read these instructions completely.

Important

▶ Before use
This clipper is designed for professional use to trim hair and beards. Charge it for 8 hours before use for the first time in order to activate the built‑in rechargeable batteries. It can be operated on either an AC adaptor or rechargeable batteries. Read all instructions carefully before use.
▶ Charging the clipper

Use the ER1421/ER1411 hair clipper with the RE9‑41 adaptor only.
Avoid charging the batteries at temperatures below 5 °C or above 35 °C.
Avoid charging the batteries in direct sunlight or near a radiating heat source.
The charge status ( ) lamp may blink at an early stage when it is used for the first time or if it has not been used for 6 or more months even if it is fully charged. This is not a malfunction.
Even though the clipper may not be used for an extended period, charge every 6 months to preserve battery life.
The power cord cannot be replaced. If it is damaged, the AC adaptor should be discarded.

▶ Using the clipper

Warning ‑ Keep the appliance dry.
The clipper may become warm during operation and/or charging. This is normal.
Check that the blades and the attachments are not damaged before use. Replace them if they are damaged.
You should not allow permanent wave lotion, hair restorer, or hair spray to come into contact with the main body or the blades.
Doing so may result in cracking, discoloring or corrosion.
You should not drop the clipper on the floor.
You should not knock the blades and the attachments against hard objects.
You should not trim the hair of a pet.

▶ Cleaning the clipper

Clean the housing using only a cloth slightly dampened with water or a mild soap solution.
Never use a caustic solution.
Never submerge the clipper in water.

▶ Storing the clipper

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Never tamper with moving parts.
Avoid grabbing the clipper by the power cord, as it may become detached, causing damage or injury.
If the clipper is not working properly, have it inspected at an authorized service center.

Speciﬁcations

Power source: See the nameplate on the product. (Automatic voltage conversion)
Motor voltage: 2.4 V DC
Charging time: 1 hour

Airborne Acoustical Noise: 64 (dB (A) re 1 pW) ER1411
71 (dB (A) re 1 pW) ER1421
READ ALL INSTRUCTIONS BEFORE USE.

Parts identiﬁcation

Panasonic ER1421 ER1411 AC Rechargeable Professional Hair Clipper -
Fig

A The Main Body
1 0·CHARGE/1 switch
2 Charge status ( ) lamp
3 Appliance socket
B Blade
4 Mounting hook
5 Cleaning lever
6 Moving blade
7 Stationary blade| C 3 mm/6 mm comb attachment
D 9 mm/12 mm comb attachment
E 15 mm/18 mm comb attachment
F AC adaptor (RE9‑41)
8 Power cord
9 Appliance plug
G Cleaning brush
H Oil
I Charging stand ER1421
10: Charging plug
11; Socket
J Comb attachment shelf ER1421
K Connector ER1421
---|---

Charging the hair clipper

Charging with the charging stand ER1421
1 Connect the power cord to the charging stand.
2 Slide the 0·CHARGE/1 switch to “0·CHARGE”.
3 Place the clipper on the charging stand and plug the adaptor into a household outlet.

Panasonic ER1421 ER1411 AC Rechargeable Professional Hair Clipper -
Fig1

Charge status ( ) lamp glows in red and charging starts.
Charging is completed when the Charge status ( ) lamp blinks in red once every second. (Max. 1 hour later)
10 minutes after charging is completed, the charge status ( ) lamp blinks in red once every 2 seconds.
1 full charge will provide approximately 80 minutes of continuous operation.

Connecting the comb attachment shelf to the charging stand ER1421
Determine the connection position for the charging stand and comb attachment shelf. Firmly insert the connector into the slot at the bottom of the charging stand. If the unit wobbles, then further push in the connector since it has not been firmly inserted. ▶ Charging without the charging stand

Slide the 0·CHARGE/1 switch to “0·CHARGE”, and insert the appliance plug into the clipper.
Plug the adaptor into a household outlet.

▶ AC operation
If you connect the AC adaptor to the clipper in the same way as for charging and turning on the power, you can use it even if the battery capacity is low.

If the clipper does not operate, charge the clipper for approximately 1 minute.
Be careful not to discharge the battery completely with the power left turned on. It results in shortening the battery life.

Using the hair clipper

▶ Using the comb attachments

Select the trimming heights indicated on the insides and sides of the attachments.
Mount the attachment to the clipper as illustrated.

Removing the attachment from the clipper
Slide one side of the attachment of the mounting in the direction indicated by the arrow.

Blade maintenance

Removing and mounting the blade
▶ Removing the blade

Hold the clipper with the switch facing upward and push the blade with your thumb while catching the blade in your other hand.
• Be sure to turn off the power before you remove the blade.

▶ Mounting the blade

Fit the mounting hook into the blade mounting on the clipper and push in until it clicks.

Cleaning the blade Panasonic ER1421 ER1411 AC Rechargeable Professional
Hair Clipper - Fig9

Brush off any hairs from the clipper and from around the blade.
Remove the blade and brush off the hairs from the blade edge.
Brush the hairs out from between the stationary blade and the moving blade while pressing down on the cleaning lever to raise the moving blade.

Lubrication

Apply a few drops of the oil to the space between the stationary blade and the moving blade.
• Apply the oil to the clipper before and after each use.
Remount the blade on the clipper.

Removing the built-in rechargeable batteries

Remove the batteries as illustrated.

Disconnect the clipper from a household outlet.
Fully discharge the batteries.
Be careful not to short‑circuit the batteries.

WARNING ‑ Do not attempt to replace the batteries for the purpose of reusing the clipper. This could result in the risk of fire or electric shock.
Important notice regarding environmental protection
The built‑in rechargeable Nickel‑Metal Hydride batteries contain substances that may be environmentally harmful. Please remove the batteries before discarding your clipper.
For environmental protection and recycling materials
This clipper contains Nickel‑Metal Hydride batteries.
Please make sure that the batteries are disposed of at an officially assigned location if there is one in your country. Please read “Information for Users on Collection and Disposal of Old Equipment and used Batteries” on page 87.
Please read “Information for Users on Collection and Disposal of Old Equipment and used Batteries” on page 87.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery, and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about the collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service, or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

Cd
This symbol might be used in combination with a chemical symbol. In this case, it complies with the requirement set by the Directive for the chemical involved.

MEMO

Panasonic Electric Works Wanbao (Guangzhou) Co., Ltd.
http://panasonic.net
Printed in China

Documents / Resources

| Panasonic ER1421/ER1411 AC/Rechargeable Professional Hair Clipper [pdf] User Manual
ER1421 ER1411 AC Rechargeable Professional Hair Clipper, ER1421 ER1411, AC Rechargeable Professional Hair Clipper, Professional Hair Clipper, Hair Clipper, Clipper
---|---