better bathrooms BeBa-26279 Nambi Column Traditional Radiator User Manual

better bathrooms BeBa-26279 Nambi Column Traditional Radiator

Congratulations on your purchase

• And welcome to our growing gang of sawy shoppers
• We’re on a mission to bring you extraordinary bathroom products, for less. From modern to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So, you can fall in love with your space every single day.
• As one of the UK’s largest independent bathroom stores, we’ve received countless awards; including the National Business Awards UK, the Digital Entrepreneur Awards and being placed on The Sunday Times Fast Track 100.
• We hope your new product goes above and beyond your expectations. However, should any problems occur, please:
• log in to your account and contact our customer services team via your self-serve portal – betterbathrooms.com/CustomerAccount/Login. contact us via betterbathrooms.com/content/contact-us.

Important information

• Please read these instructions thoroughly and retain for future reference
• Manufactured to BS EN 442-1 Radiators and convectors
• Please ensure that the product is checked for damage prior to installation, any damage reported after installation will not be covered.
• The pipework must be flushed out to remove any debris which can affect the function of this product.
• A corrosion inhibitor should be used in your installation.

BTU & Wattage info-

Parts

Please note that Parts are for illustrative purposes only and may differ slightly to the actual product

Tools required

• Spanner
• Flathead screwdriver
• Philips screwdriver
• Tape measure
• Drill and 8mm drill bit
• Spirit Level
• Pencil
• Sealing tape

Installation

Please note: Before starting any installation, tum off the water supply.
Please note: Before commencing any installation, the desired location should be checked before drilling, that no pipes or wires can be damaged. First, prepare the water supply pipes to match up with the towel radiator and valve dimensions being used. Fit the radiator valve tail and nut into the radiator (at both sides) and using sealing tape, tighten into position, then follow the installation below.

1. Insert the blanking cap and air vent in the top of the radiator at either side, (add a little sealer tape to secure) and tighten using the spanner, be sure not to  overtighten.
2. Mark the position of the wall hanging brackets (on the wall) on either side. Use a spirit level to ensure these are aligned.
3. Using the drill and 8mm drill bit, drill into the marked positions then insert the wall plugs and tap flush to the finished wall surface.
   • Please note: If drilling into tile, it is recommended to tape the wall to prevent the drill from slipping.
4. Next, position the wall brackets and screw into place using the screws provided with the Philips screwdriver.
5. Once all brackets are secure, hang the radiator until fixed firmly into place and adjust so that the radiator aligns with the pipework.
   • Please note: You may need two people to hang the radiator, depending on the model purchased.
6. Finally, fit the radiator valves to the pipework and connect to the radiator valve tail and tighten all connections.

IMPORTANTI: The product is supplied un-filled. The radiator should be filled with a water (80%) and glycol (20%) mixture if NOT being connected to the central heating system, also allow 5% air gap.

After installation

• After the above installation, tum on the water supply and using the flathead screwdriver, open the air vent via the central screw, open the inlet valve and let the water rush into the radiator. Check all connections for leaks.
• Once water overflows from the air vent, this means that there will be no air bubbles present.
• Use a screwdriver to close the air vent and then the radiator is ready to use.

Cleaning

• This radiator is made from steel with a painted finish.
• To maintain the surface of your product, wipe with a clean damp cloth and wipe dry.
• Do not use abrasive cleaning agents or materials which can strip and scratch the surface; the use of these agents or materials can invalidate your guarantee.
• It is recommended to wipe and dry on a regular basis.

For more information

• visit betterbathrooms.com.
• email customerservices@buyitdirect.co.uk.
• call 0330 390 3062
• write to Trident Business Park, Neptune Way, Huddersfield, HD2 IUA Part of the BuyItDirect Group

Please note: Image is for illustrative purposes only and may differ slightly to the actual product

• Multi-person assembly
• Tools required
• We always recommend using professional tradespeople to install your product
• V2_16.11.22

Thank you for choosing Better Bathrooms. Please read this manual before installing your product and keep for future reference.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>