DINAN D180-0015-B Matte Carbon Fiber Strut Tower Brace User Manual

DINAN D180-0015-B Matte Carbon Fiber Strut Tower Brace

Product Information

• Specifications
  • Manufacturer: Dinan Engineering
  • Model: D180-0015 & D180-0015-B
  • Compatibility: G8x M2/M3/M4
  • Part Number: D183-0073
  • Description: Engine Strut Brace
• Description
  • The Dinan Enhanced Engine Strut Brace is a high-performance product designed to provide increased performance, durability, and an aesthetic design.
  • It is specifically designed for the G8x M2/M3/M4 models.
  • The strut brace is made of high-quality materials and has been meticulously engineered by the Dinan Engineering Team.

Installation Instructions

• Before Installation
  • Prior to performing the installation, it is recommended to familiarize yourself with the instructions provided.
  • If you do not have the required skills or tools, it is advised to seek assistance from a qualified repair facility.
  • For any difficulties during the installation or if the instructions are unclear, please contact Dinan’s Technical Support Staff at 800-341-5480.
• Parts List
  • DINAN PART # D183-0073 – ASSY, STRUT BRACE, G8X – Quantity: 1
  • D183-0073-MT – STRUT BRACE, CF SINGLE PIECE, MATTE – Quantity: 1
  • D672-0008 – M8 RECESS FLANGE NUT – Quantity: 8
• Removal of Stock System
  • Remove the front and rear brace by removing (1) bolt and (8) nuts.
• Dinan Installation
  • Step 1: Placing the Strut Brace
  • The vehicle must be fully on the ground.
  • Place the DINAN engine strut brace into position.
  • Secure it in place using the stock front bolt and the Dinan-supplied recess nuts.
  • If the brace is difficult to fit, proceed to Step 2.
• Tightening Torque:
  • M10x35 Screw (1): Torque to 56Nm (41 ft-lb)
  • M8 Nut (8): Torque to 28Nm (20 ft-lb)
  • Step 2: Adjusting the Brace
  • If the brace does not slide over the studs, adjustment may be needed on both the left and right side of the spring strut support hat. These parts may have some variability from vehicle to vehicle and will not affect alignment.
  • Loosen all bolts shown in the diagram.
  • Adjust until the brace slides over the studs.
  • Step 3: Final Adjustments
  • Loosely put the nuts back on and adjust the support hat so that the brace studs align better (more concentric) with the nuts. Finally, torque the brace down as shown in Step 1.
• FAQ
  • Q: What should I do if I encounter difficulties during installation?
  • A: If you encounter any difficulties during the installation process or if the instructions are unclear, please contact Dinan’s Technical Support Staff at 800-341-5480 for assistance.

overview

• Thank you for being selective enough to choose a Dinan Enhanced Engine Strut Brace.
• The Dinan Engineering Team has spent many hours developing this product to assure that you will receive increased performance, durability and an aesthetic design that you as a customer will be able to enjoy for many years.
• Ease of installation and maintenance is important to us and has been highly considered throughout the design process.
• Prior to performing the installation, familiarize yourself with these instructions as it should help you with the process.
• If you feel that you do not have the required skills or tools, please arrange for a qualified repair facility to perform the installation.
• If you have any difficulties during the installation, or if these instructions are not clear to you, please call Dinan’s Technical Support Staff at 800-341-5480. Again, thank you for choosing Dinan. Enjoy.

Installation Instructions

• D180-0015 & D180-0015-B:
• G8x M2/M3/M4
• Engine Strut Brace
  • Document Revision: C
  • Release Date: October 28, 2023

PARTS LIST

REMOVAL OF STOCK SYSTEM

| STEP 1: Remove front and rear brace by removing (1) bolt and (8) nuts. For M2 only – remove edge seal and cosmetic covers as needed to access rear brace fasteners.
---|---

DINAN INSTALLATION

| STEP 1:  The vehicle must be fully on the ground  Place DINAN engine strut brace into position. Secure into place using the stock front bolt, and Dinan- supplied recess nuts. Go to STEP 2 if brace is hard to fit.
TIGHTENING TORQUE: M10x35 Screw (1): Torque to 56Nm (41 ft-lb) M8 Nut (8): Torque to 28Nm (20 ft-lb)
---|---
| STEP 2: If the brace does not slide over the studs, adjustment may be needed on both left and right side of the spring strut support hat. These parts do have some slop and may vary from vehicle to vehicle. This support is not coupled with the suspension and will NOT affect alignment.  Loosen all bolts shown.  Adjust until the brace slides over the studs.
| STEP 3:** Loosely put the nuts back on and adjust the support hat so the brace studs align better (more concentric) with the nuts.
Re-torque support hat bolts: Red: 28 Nm (20 ft-lb), Angle of Rotation 120® Yellow: 56 Nm (41 ft-lb)  Torque the brace down as shown in STEP 1. ENJOY.
---|---

CONTACT

• Dinan Engineering
• 4800 US Hwy 280 West
• Opelika, AL 36801
• Phone: 800.341.5480
• INS180-0015 REV. C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>