YEELIGHT YLDDL-0083 Smart Ceiling Spotlight User Manual
- June 15, 2024
- Yeelight
Table of Contents
YEELIGHT YLDDL-0083 Smart Ceiling Spotlight User Manual
Product Information
Specifications
- Model: YLDDL-0083, YLDDL-0083-B
- Lamp Holder: GU10
- Rated Input: 220-240V~50/60Hz
- Rated Power: 4.5W each lamp holder
- Maximum wattage placement bulb: 50W
Model:| YLDDL-0084, YLDDL-0084-B
---|---
Lamp Holder:| GU10
Rated Input:| 220-240V~50/60Hz 50mA
Rated Power:| 4.5W each lamp holder
Maximum wattage placement bulb:| 50W
Model:| YLDDL-0085, YLDDL-0085-B
---|---
Lamp Holder:| GU10
Rated Input:| 220-240V~50/60Hz
Rated Power:| 4.5W each lamp holder
Maximum wattage placement bulb:| 50W
Product Description
The spotlight is a lighting fixture designed for indoor use. It comes with a
lock switch for easy operation. The front view of the light body features a
mounting hole for self-tapping screws, while the reverse view includes a
wiring hole. The base plate provides support and stability, and there is a
threading hole for convenient installation. The spotlight also comes with an
expansion tube for mounting purposes.
Product Usage Instructions
Mounting Instructions
- Take out the spotlight from the package and remove the base in the opposite direction according to the installation instructions of the base.
- To avoid any danger, please ask an electrical professional to perform mounting or maintenance.
- Before mounting, make sure to disconnect the power supply to prevent electric shock. Mounting should be performed in strict accordance with the instructions. Improper mounting is liable to cause accidents such as fall, fire and electric shock.
- Use an impact drill 6 mm in diameter to make two mounting holes with a length of ≥ 25mm in the wall (as shown in the following figure). Put the expansion tube into the mounting hole, and then thread the power cord though the wiring hole. Use self-tapping screws to fix the base on the ceiling, and verify the base is securely mounted.
- The wiring hole is suitable for power leads with a cross-sectional area of 1.5-2.5 mm2. Strip the power cord by 11-13mm, and connect the neutral, live and ground wires to the ceiling light.
- A solid or stranded hard wire is used as the power lead.
- Connect the neutral, and live wires to the wiring holes marked with N, and L in turn. (Open the internal junction box at the back of the spotlight, connect the wires and tighten the screws with an electrician’s screwdriver.)
- Holed both sides of the lamp with both hands, align the lamp with the fixed base, then push the spotlight to the left or right at the same time (depending on the orientation of the base). When you hear a “click”, the installation is complete.
- Aways check for proper mounting after you have finished. Improper mounting may cause the product to fall.
- Align the bulb with the GU10 interface in the spotlight tube, and then rotate it clockwise to complete the installation. After completing the installation, please make sure that the spotlight base is securely installed.
Precautions
- Do not replace the light source of the ceiling light by yourself. The light source should only be replaced by the manufacturer, after-sales service, or a qualified electrician.
- The light installation requires a qualified electrician, and the wiring must comply with IEEE electrical standards or national standards.
- Make sure the voltage is consistent with the ceiling light’s operating voltage before use. Using the mismatched voltage may damage the ceiling light and cause safety hazards.
- The ceiling light generates heat during work. Please keep it is well-ventilated for heat dissipation.
- The ceiling light should be installed in a stable location to prevent it from dropping down or falling off.
- Under normal use of conditions, this equipment should be kept a separation distance of at least 20 cm.
- For indoor use only.
EU Declaration of Conformity
Quingdao Yeelink Information Technology Co., hereby declares that type Y00409
devices conform with EU Directives. The full text of the EU Declaration of
Conformity is available at the following web address:
https://edshop.edsystem.cz/prohlaseni-o-shode/article-28393
WEEE
This product must not be disposed of as normal household waste by the EU
Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU).
Instead, it shall be returned to the place of purchase or handed over to a
public collection point for the recyclable waste. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. Contact your local authority or
the nearest collection point for further details. Improper disposal of this
type of waste may result in fines by national regulations.
Bulb Installation
Align the bulb with the GU10 interface in the spotlight tube and rotate it clockwise to complete the installation. After installation, ensure that the spotlight base is securely installed.
FAQ (Frequently Asked Questions)
Q: Can I use this spotlight outdoors?
A: No, this spotlight is designed for indoor use only.
Q: What is the maximum wattage placement bulb for this spotlight?
A: The maximum wattage placement bulb for this spotlight is 50W.
Q: Where can I find the EU Declaration of Conformity?
A: The EU Declaration of Conformity can be found at the following web
address: https://edshop.edsystem.cz/prohlaseni-o-shode/article28393
Dovozce
1262/95, 7900 Ostrava, republika,
www.edsystem.cz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>