Greenworks ST24L01 24V 13 Inch Brushless String Trimmer Gen 2 User Manual

ST24L01
STRING TRIMMER
OPERATOR MANUAL

STG403
www.greenworkstools.com

DESCRIPTION

1.1 PURPOSE
This machine is used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost.

1.2 OVERVIEW

1. Rear handle
2. Trigger
3. Lock-out button
4. Speed button
5. Rotate button
6. Upper shaft
7. Auxiliary handle| 8. Coupler
9. Lower shaft
10. Cut-off blade
11. Edge guide
12. Trimmer head
13. Edging guide wheel
14. Guard
---|---

IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING (THIS

POWER TOOL)

WARNING
Read and understand all instructions before using this product. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

• Use only identical manufacturer’s replacement parts and accessories. Use of any other parts may create a hazard or cause product damage.
• Always wear safety glasses with side shields marked to comply with ANSI Z87.1. Everyday glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury. Use face mask if operating in dusty work spaces.
• Avoid Dangerous Environment – Don’t expose power tools to damp or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Don’t use in rain.
• Keep all bystanders, children, and pets at least 50 ft. away.
• Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.
• Use right Appliance. Do not use appliance for any job except that for which it is intended.
• Avoid Unintentional Starting – Don’t carry appliance with finger on switch. Be sure switch is off when battery is plugged in.
• Don’t Force Appliance – It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
• Don’t overreach – Keep proper footing and balance at all times.
• Stay alert – Watch what you are doing. Use common sense. Do not operate this unit when you are tired, ill or under the influence of alcohol, drugs or medication.
• Always store idle power tools indoors – When not in use, power tools should be stored indoors in a dry and high or locked-up place, out of reach of children.
• The machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety. Children should be supervised to ensure that they do not play with the machine.
• Maintain Appliance With Care – Replace string head if cracked, chipped, or damaged in any way. Be sure the string head is properly installed and securely  fastened. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. Failure to do so can cause serious injury.
• Check damaged parts before using the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, damaged mountings, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.
• Remove or disconnect battery before servicing, cleaning or removing material from the gardening appliance.
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care. Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. Use only with Greenworks BAG709 battery or other BAG series.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use only with Greenworks 2903102/CAG801 charger or other CAG series.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130 °C) may cause an explosion.
• Do not dispose of the batteries in a fire. The cells may explode. Check with local codes for possible special disposal instructions.
• Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
• Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Keep guards in place and in working order.
• Keep hands and feet away from cutting area.
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
• Use only with the nylon cutting line of .0080″ (2 mm) diameter. Do not use heavier lines than recommended by the manufacturer and line materials of other types – for example, metal wire, rope, and the like.

SAVE THESE INSTRUCTIONS

SYMBOLS ON THE MACHINE

Some of the following symbols can be used on this machine. Please study them and learn their definition. Proper interpretation of these symbols will let you operate the tool better and safer.

follow all warnings and safety instructions.
| Always wear safety glasses with side shields marked to comply with
ANSI Z87.1 when you operate this machine.
| Keep all bystanders at least 50-ft away.
| Do not install or use any type of blade on the machine or displaying this symbol.
| Thrown objects can ricochet and result in personal injury or property damage.

RISK LEVELS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

will result in death or serious injury.
| WARNING| Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
| CAUTION| Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
| CAUTION| (Without Safety Alert Symbol) Indicates a situation that may result in property damage.

SERVICE

Servicing requires extreme care and knowledge and must be performed only by a qualified service technician. For service we suggest you return the machine to your nearest AUTHORIZED SERVICE CENTER for repair. Use only identical manufacturer’s replacement parts and accessories.

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The toxic and corrosive materials below are in the batteries used in this machine: Lithium-ion, a toxic material.

WARNING
Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding damaged or worn out Lithium-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for Lithium- ion disposal.

WARNING
If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use. Discard it and replace with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:

• Cover the terminals of the battery with heavy-duty adhesive tape.
• DO NOT try to remove or destroy any of the battery pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on skin, and do not swallow it.
• DO NOT put these batteries in your regular household trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.

PROPOSITION 65

WARNING
This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well- ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

INSTALLATION

8.1 UNPACK THE MACHINE

WARNING
Make sure that you correctly assemble the machine before use.

WARNING

• If parts of the machine are damaged, do not use the machine.
• If parts are missing, do not operate the machine.
• If parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

WARNING
For your personal safety, do not insert battery before the tool is assembled completely.

8.2 ATTACH THE GUARD

WARNING
Do not touch the cut-off blade.

1. Pull the edge guide until the open end on the slot.

2. Remove the screw from the guard with a Phillips head screwdriver (not included).

3. Put the guard onto the trimmer head.
   

4. Align the screw hole on the guard with the screw hole on the trimmer head.

5. Tighten the screw.
   

8.3 ATTACH THE WHEEL

1. Remove the screw from the wheel with a Phillips head screwdriver (not included).

2. Put the wheel onto the trimmer head.
   

3. Align the screw hole on the wheel with the screw hole on the trimmer head.
   

4. Tighten the screw.

8.4 ASSEMBLE THE SHAFT

1. Loosen the screw on the coupler.

2. Push in the release button (1) on the lower shaft.

3. Align the release button with the positioning hole (2) and slide the two shafts together.
   

4. Turn the lower shaft until the button locks into the positioning hole.
   NOTE
   The release button must be fixed in the positioning hole. Using the wrong hole could lead to personal injury, or damage to the unit.

5. Tighten the screw with the hex wrench.
   

8.5 ATTACH THE AUXILIARY HANDLE

1. Remove the knob (1) from the handle.
2. Attach the auxiliary handle and lower clamp (2) on the shaft.
3. Set the auxiliary handle in the comfortable position.
4. Put the bolt (3) through the holes.
5. Tighten the auxiliary handle with the knob.

OPERATION

IMPORTANT
Before you operate the machine, read and understand the safety regulations and the operation instructions.

WARNING
Be careful when you operate the machine and always observe your surroundings before operating tool.

9.1 INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.
• Read, know, and do the instructions in the battery and charger manual.

1. Align the lift ribs on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

9.2 REMOVE THE BATTERY PACK

1. Push and hold the battery release button (1).
2. Remove the battery pack from the machine.
   

9.3 START THE MACHINE

1. Push the lock-out button (1) and pull the trigger (2).
2. Push the speed switch (3) to the desired operating speed. Push the speed switch to position 1 for low speed or position 2 for high speed.
   

9.4 STOP THE MACHINE

1. Release the trigger to stop the machine.

9.5 ADJUST THE LENGTH OF THE CUTTING LINE

NOTE
The machine has an auto-feed head. If the cutting line does not automatically advance, it can be tangled or empty.

1. Start the machine and keep 3s. Release the trigger until the machine totally stops.
2. Repeat the above step until you can hear the line-cutting noise.

NOTE
The line will extend approximately 0.4 in. with each stop and start of the switch trigger until the line reaches the cut-off blade and the cut-off blade cuts the excess length.

NOTE
Do not pull or release the trigger too fast.

NOTE
It will damage the machine if you hit the head to try to advance the line.

9.6 LINE CUT-OFF BLADE
This trimmer is equipped with a line cut-off blade on the guard. The line cut off blade continuously trims the line to ensure a consistent and efficient cut diameter. Advance line  whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep line long enough to advance properly.

9.7 OPERATION TIPS
WARNING
Keep clearance between the body and the machine.

WARNING
Do not operate the machine without guard in place.

Do these tips when you use the machine

• Keep a firm hold with both hands on the machine while you operate the machine.
• Cut tall grass from the top down.

If grass winds around the trimmer head:

• Remove the battery pack.
• Remove the grass.

9.8 CUTTING TIPS

• Tilt the machine toward the area to be cut. Use the tip of the cutting line to cut grass.
• Move the machine from right to left to prevent thrown debris from hitting the operator.
• Do not cut in the danger area.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and breakage. Stone and brick walls, curbs, and wood can wear the cutting line quickly.

9.9 CHANGE TO THE EDGING MODE

NOTE
You can change the trimmer to an edger to keep patios, driveways and sidewalks well groomed.

1. Stop the machine.

2. Push on the edge button (1) and rotate the trimmer head until the guard and the shaft are parallel.
   

3. Push the rotate button (2) and turn the rear handle clockwise 90°.
   

4. Loosen the knob (3) on the auxiliary handle and turn the auxiliary handle to a comfortable position.

5. Tighten the knob.
   

MAINTENANCE

IMPORTANT
Read and understand the safety regulations and the maintenance instructions before you clean, repair or do the maintenance work on the machine.

IMPORTANT
Make sure that all nuts, bolts and screws are tight.
Check regularly that the handles are firmly mounted.

IMPORTANT
Use only the replacement parts and accessories of the initial manufacturer.

10.1 GENERAL INFORMATION

IMPORTANT
Only your dealer or approved service center can do the maintenance that is not given in this manual.
Before the maintenance operations:

• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Use correct clothing, protective gloves and safety glasses.

10.2 CLEAN THE MACHINE

• Clean the machine after use with a moist cloth dipped in neutral detergent.
• Do not use aggressive detergents or solvents to clean the plastic parts or handles.
• Keep the trimmer head free of grass, leaves, or excessive grease.
• Keep the air vents clean and free of debris to avoid overheating and damage to the motor or the battery.
• Do not spray water onto the motor and electrical components.

10.3 REPLACE THE SPOOL

1. Push the tabs (2) on the sides of the trimmer head at the same time.
   

2. Pull and remove the spool cover (1).

3. Remove the spool (3).
   

4. Replace with a new spool.
   NOTE
   Make sure that the cutting line is in the guide slot on the new spool, and is extended approximately 5 in. before you install the new spool.

5. Put the end of the cutting line through the eyelet (4).
   

6. Extend the cutting line to release it from the guide slot in the spool.

7. Push the tabs and install the spool cover onto the spool housing (5).
   

8. Push the spool cover until it clicks into position.

10.4 REPLACE THE CUTTING LINE

NOTE
Remove the remaining cutting line on the spool.

NOTE
Use only with the nylon cutting line of .0080″ (2 mm) diameter.

1. Cut a piece of cutting line approximately 3m long.

2. Bend one end of the line 1/4 of an inch (6.35mm)
   

3. Insert the line into the anchor hole of the spool.
   

4. Wind the cutting line around the spool tightly in the indicated direction.
   

5. Put the cutting line in the guide slot.
   

6. Do not wind the cutting line beyond the edge of the spool.

TRANSPORTATION AND STORAGE

11.1 MOVE THE MACHINE
When you move the machine, you must:

• Wear gloves.
• Stop the machine.
• Remove the battery pack and charge it.
• Assemble the blade guard.

11.2 STORE THE MACHINE

• Remove the battery pack from the machine.
• Make sure that children cannot come near the machine.
• Keep the machine away from corrosive agents such as garden chemicals and de-icing salts.
• Secure the machine during transportation to prevent damage or injury. Clean and examine the machine for any damage.

TROUBLESHOOTING

2. Check contact and install the battery pack again.
The battery pack is depleted.| Charge the battery pack.
The lock-out button and trigger are not pushed at  the same time.| 1. Pull the lock-out button and hold it.
2. Pull the trigger to start the machine.
The machine stops when  you cut.| The guard is not attached to the machine.| Remove the battery pack and attach the guard to the  machine.
Heavy cutting line is used.| Use only with the nylon cutting line of .0080″ (2 mm) diameter.
The grass winds around the motor shaft  or  the trimmer head.| 1. Stop the machine.
2. Remove the battery pack.
3. Remove the grass from the motor shaft and  trimmer head.
The motor is overloaded.| 1. Remove the trimmer head from the grass.
2. The motor will recover to work as soon as the load  is removed.
3. When you cut, move the trimmer head in and out  of the grass to be cut and remove no more than 8″ in  pass.
The battery pack or machine is too hot.| 1. Cool the battery pack until its function returns to  normal.
2. Cool the machine for approximately 10 minutes.
The battery pack is disconnected from the tool.| Install the battery pack again.
The battery pack is depleted.| Charge the battery pack.
The line does not advance.| Lines are welded to themselves.| Lubricate with silicone spray.
Not enough line on spool.| Install more line.
Lines are worn too short.| Advance the cutting line.
Lines are tangled on spool.| 1. Remove the lines from the spool.
2. Wind the lines.
The line keeps breaking.| The machine is used incorrectly.| 1. Cut with the tip of the line, avoid stones, walls and  other hard objects.
2. Advance the cutting line regularly to keep full cutting width.
The grass winds around the  trimmer head and motor housing.| Cut tall grass at ground level.| 1. Cut tall grass from the top down.
2. Remove no more than 8″ in each pass to prevent  rapping.
The line does not cut well.| The cut-off blade becomes dull.| Sharpen the cut- off blade with a file or replace it.
Vibration increases obviously.| The line is worn down at one side and not advanced in time.| Make sure that the line on both sides is normal.  Advance the line.

TECHNICAL DATA

The recommended ambient temperature range:

LIMITED WARRANTY

3 YEAR
LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. Greenworks, at its own discretion, will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been purchased or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners’ manual supplied with the product when new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.

HELPLINE:
Warranty service is available by calling our toll-free helpline at 1-888-909-6757.

TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless  such return is requested in writing by Greenworks.

USA address:
Greenworks Tools
P.O. Box 1238
Mooresville, NC 28115| Canadian address:
Greenworks Tools Canada, Inc.
P.O. Box 93095, Newmarket,
Ontario L3Y 8K3
---|---

REPLACEMENT PARTS

www.greenworkstools.com

P0804458-00 Rev B

Documents / Resources

| Greenworks ST24L01 24V 13 Inch Brushless String Trimmer Gen 2 [pdf] User Manual
ST24L01, STG403, ST24L01 24V 13 Inch Brushless String Trimmer Gen 2, 24V 13 Inch Brushless String Trimmer Gen 2, 13 Inch Brushless String Trimmer Gen 2, Brushless String Trimmer Gen 2, String Trimmer Gen 2, Trimmer Gen 2
---|---

References

• Greenworks Outdoor Power Equipment, Lawn & Garden Tools

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>