Hetoy HL-2888 12V Kids Ride On Car Licensed Mercedes Benz G63 Electric Vehicles Installation Guide

: June 15, 2024
: Hetoy

Table of Contents

SPECIFICATION
PARTS LIST
PARTS DIAGRAM
ASSEMBLY STEPS
HOW TO OPERATE YOUR VEHICLE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Hetoy HL-2888 12V Kids Ride On Car Licensed Mercedes Benz G63 Electric Vehicles Installation Guide

WARNING:

FOR THE SAFETY OF YOUR CHILD, PLEASE READ ALL WARNINGS AND ASSEMBLY/USE INSTRUCTIONS. KEEP THIS GUIDE FOR FUTURE REFERENCE.

ADULT ASSEMBLY REQUIRED. The product contains small parts, which are for adult assembly only. Keep small children away when assembling.
Always remove protective material and poly bags and dispose before assembly

SPECIFICATION

Battery: 12V4.5AH 1
Motor: 12V25W2
Charger: input:100-240VAC 50/60Hz 0.3A output:12VDC 500mA
Maximum load: 30 KG
Work Time: Recharge 8-12h, Use for 1-2h
Speed: 3-5KM/H
Age: 37-96 months
R/C Battery: AAA1.5V2
R/C Distance: 15±5M

Thank you for purchasing our product. Please read this manual carefully before using this product, install

and use this product according to this manual, and pay attention to safety precautions.

PARTS LIST

PART NAME	PICTURE	QTY (PCS)
Vehicle body		1
Seat		1
Driving wheel		4
Steering wheel		1
M10 Nut		4
The spare tire		1
M5 Nut (Placed on the steering wheel)		1
Wrenches		2
Windshield		1
10 Washer		6
ST4*12 Screw (Placed on the steering wheel)		2
Charger		1
Instruction Manual		1
M5*25 (Placed on the steering wheel)		1
Wheel		4

PARTS DIAGRAM

NOTE: Some Parts Shown are assembled on both sides of vehicle

Vehicle body *1
Windshield*1
Seat*1
Gear box*1
Driving wheel*2
Wheel*3
Steering wheel*1
Steering shaft*1
Rear axle*1
M525 bolt1
M10 Nut *4
Rear view mirror*2
M5 Nut*1
ST412 Screw2
Wheel hube*4
Ø10 Washer*6

Tools Required
(not included)

Screwdriver

Pliers

Hammer

Spanner

ASSEMBLY STEPS

Your new vehicle requires adult assembly. Please set aside at least 40 minutes for assembly. Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, or help in assembly of the vehicle.
Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
Assembly tool for need: screwdriver(not included), pliers(not included), hammer(not included), Spanner(not included).

Install the back wheel

Tum over the car body, disconnect the rear axle parts, keep one washer, then put the rear axle through the car body.
Put the gear box is arranged on the left.(when reverse side up)
Put the driving wheel through the back axle and fix it with washer, nut and the wheel hub in turn.
Put the washer, wheel and another washer through the back axle on the other side in turn, then fix them with nut and wheel hub.

Install the front wheel

Remove the nut and washer on the front axle;
As showed in the picture, fix the washer, wheel, washer and nut onto the axle in proper order.
Fasten the nut with spanner.
Fix the wheel hub.
Fix another wheel on the other side.

Install the steering shaft

Turn the vehicle body on its side
Slide the M10 washer onto the steering shaft from the straight end(PIC 1).
Insert the straight end of steering shaft through the hole in the vehicle body and out through the hole in the dashboard.
Insert the bent end into the hole in the front axle secure it with split pins1 and M10 washer1(PIC 2,3).

Install the steering wheel

As showed in the picture, remove the nut and bolt from the steering wheel, connect the steering wheel and gauge board middle connector.
As showed in the picture, install the steering wheel, and fasten with nut and bolt.

Connect the power supply

Plug the wire connector into the motor connector.
Plug the power connector into the terminal on battery as shown.

Install the seat

As showed in the picture, install the seat to the corresponding place, and fasten with the screws.

Install the windshield

As showed in the picture, press the windshield downward to fix it.

Install the rear view mirror

As showed in the picture, press the rear view mirror downward to fix it.

IMPORTANT SUPPLEMENT TO INSTRUCTION MANUAL

After assembling any wheel to the axles, please check the gap between the screw thread and the collapsible (refer to below picture), if the gap is too big, please add two or three washers inside the wheel, But after tightening the nut outside the wheel, please turn the wheel by your finger to check if the wheel can run smoothly, this is very important, because if the wheel can run smoothly, it is ok, but if the nut press the wheel and the wheel can’t run smoothly, the motor will be broken easily! Then you need to decrease one or two washers to make sure the wheel can run smoothly!