BEISIT F20H UHF RFID Reader User Manual
- June 15, 2024
- BEISIT
Table of Contents
BEISIT F20H UHF RFID Reader
- Product Name： UHF RFID Reader
- Product Model ：FBUR-F20H-S01
Product Appearance
Hardware Functionality
Product Features
UHF RFID dual-channel industrial-grade reader with high protection level and high performance, possessing strong anti-interference capability. It adopts an industrial connector design and is enclosed in a full aluminum alloy shell, making it suitable for various industrial application scenarios.
Basic Parameters
RFID Protocol |
EPC C1G2/ISO 18000-6C | Sensitivity |
-86dBm |
|---|---|---|---|
Maximum Power |
33dBm | Read Rate |
>800张/s |
Frequency |
860~960Mhz | Read Range |
>15m（Relating to Antennas and Tags） |
Power supply |
DC9~36V | Dimensions |
127(L)109(W)38(H)mm |
Weight |
<600g | Storage Temperature |
-40~+85℃ |
Operating Temperature |
-40~+70℃ | Environmental Humidity |
5%~95%rh |
Interface
****Power Interface| M12-4P-A-Female| Communication Interface|
M12-4P-D-Female(LAN)
M12- 8P-A-Male(RS232、RS485)
---|---|---|---
RF Interface| 2个TNC,External Thread and Internal Pin|
Indicator light
Power light| Green light (always on when powered, indicating normal
operation)
---|---
Signal light| upgrading, it flashes once every 1 second; there is a
fault, it flashes twice every 1 second.
Network light| ** Green light (remains constantly on when the network
connection is successful)
Network data light| Yellow light (flashes during network data
transmission)
Antenna light**| Blue light (remains constantly on after antenna setup,
flashes when reading tag data)
Certification
| Certification | SRRC、CE、FCC、ROHS、IP |
|---|
Software Functionality
Support Agreement
IEC\ISO EPC C1G2/ISO 18000-6C 、ISO 18000-6B(Optional equipment)
Support for Other Features
- Support online firmware burning and upgrading
- Support multiple communication protocols and interfaces
- Support standard functions of air interface protocol: read, write, lock, kill, etc.
- Support various data upload modes including EPC+TID, EPC+USER, EPC+RFU, EPC+TID+USER, EPC+TID+RFU
- Support various tag reading modes for different scenarios: multi-tag group reading, single-tag long-rang reading, adaptive reading, low-power mode
- Support power setting: 5~28dBm, adjustable in 1dBm steps
- Support working frequency band setting for each region, customizable frequency band or frequency point setting
- Support tag return of RSSI, carrier, and phase
- Support over-temperature protection with temperature accuracy of 0.5 degrees
- Support setting of working time and interval time for each antenna
- Support BLF parameter link setting for strong group reading performance
- Support filtering tag operations, support network heartbeat packets, support CW wave switch, Session value setting, Q value setting
- Support software and hardware watchdog
- Support remote restoration of factory settings.
Interface Definition
Power
Working power supply Type 1
Device M12-4PIN-A Male
| P1 VIN
P2 VIN
P3 GND
P4 GND
Working power supply Type 2
Device M12-4PIN-A Female
| P1 VIN
P2 VIN
P3 GND
P4 GND
Communication
Ethernet
Device M12-4PIN-D Female
| P1 TX+
P2 RX+
P3 RX-
P4 TX-
Com
DeviceM12-8PIN-A Male
| P8 NC
P7 NC
P6 RS232-RX
P5 RS232-TX
P4 RS485-B
P3 RS485-A
P2 GND
P1 VIN
Other Parameters
**Product Dimensions
**
**FCC Warning**
**FCC Radiation Exposure Statement:**
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2 : Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
TEL: +0086-571-8936 2888
E-MAIL:info@beisit.com
https://www.beisit.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>