VEVOR KD-8801 Gem Faceting Machine User Manual
- October 30, 2023
- VEVOR
Table of Contents
VEVOR KD-8801 Gem Faceting Machine User Manual
We continue to be committed to offering tools at competitive prices. “Save Half”, “Half Price”, or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and donot necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when placing an order with us if you are saving half in comparison withthetopmajor brands.
Warning-To reduce the risk of injury, user must readinstructionsmanual carefully.
This device complies with Part 15 of the FCC Rules. Operations subject to the following two conditions:
-
This devicemaynot causeharmful interference, and
-
this device must accept anyinterferencereceived, including interference that may cause undesire do peration.
-
LED light
-
Bamboo pipe
-
secure the millstone
-
water tray
-
drainage pipes
-
manipulator
-
switch
-
frequency converter
Fittings of a machine:
-
Diamond millstone
-
Tray
-
Adaptor
-
Cooling water pipes
-
Screw
-
Three different gem fixing rod
GENERAL SAFETY RULES
WARNING: Do not attempt to operate the machine until you havereadthoroughlyand understood completely all instructions, rules, etc. contained inthismanual.Failure to comply may result in accidents involving fire, electric shock, or seriouspersonal injury. Keep thisowner’s manual and review frequently for continuoussafe operation
- Know your machine. For your own safety, read the owner’s manual carefully.Learn its application and limitations, as well as specific potential hazardspertinentto this machine. 2. Make sure all tools are properly earthed.
- Keep guards in place and in working order. If a guard must be removedformaintenance or cleaning,make sure it is properly replaced beforeusingthemachine again.
- Keep your work area clean. Cluttered areas and workbenches increasethechance of an accident.
- Do not use in dangerous environments. Do not use power tools indamporwetlocations, or expose them to rain. Keep work areas well illuminated.
- Keep children away. All visitors should be kept a safe distance fromtheworkarea.
- Do not force the machine. It will do the job better and be safer at therateforwhich it is designed.
- Use the right tools. Do not force the machine or attachments todoajobforwhich they are not designed. Contact the manufacturer or distributor if thereisanyquestion about the machine’s suitability for a particular task.
- Wear proper apparel. Avoid loose clothing, gloves, ties, rings, bracelets, andjewellery which could get caught in moving parts. Non-slip footwear isrecommended. Wear protective hair covering to contain long hair. 10. Do not over-reach. Keep proper footing and balance at all times. 11. Maintain the machine in good condition. Keep the machine cleanfor best andsafest performance. Follow instructions for lubrication and changingaccessories.
- Disconnect the machine from power source before servicing and whenchanging the blade.
- Never leave the machine running unattended. Turn the power off. Donot leave the machine until it comes to a complete stop.
- Do not use any power tools while under the effects of drugs, alcohol ormedication.
- Always wear a face or dust mask if operation creates a lot of dust and/orchips.Always operate the tool in a well ventilated area and provide for proper dust removal. Use a suitable dust extractor.
Instruction
Controller 1. The Stop/Start button. 2. Indicator light. 3. Rotate
forwardandbackward buttons. 4. Speed regulating potentiometer knob
adjustablespeedrange 0-2980 RPM. 5. Machine switch
To fix the screws of the manipulator, the manipulator can move
forwardandbackward
Height adjuster, used to adjust the angle between the operator
andthegrindingdisc, that is, the angle of the workpiece. Unilateral rotation
for fineadjustment
Fan angle card
Dial indexing pin
Hand control lever controls gem Angle
The manual control lever can be disassembled to adjust the angleanddisassemble
the gem.
Screw control 90 degree fine tuning angle
With the positioning rotation of 96 scale, can accurately control thegemAngle
Rotate and fix the slime stick
Remove the orange baffle on the water baffle plate, which can givethestonesurface grinding
Gem surface grinding
LED light switch
Tap switch, can control the water outlet
The faucet is connected to thewater pump
Drain pipe
- Power socket.
- If any indicator light is off, please check the fuse
WARNING!
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this document,
refer toitoften, and use it to instruct other operators. Failure to read,
understand and follow the instructions in this manual may result in fire or
serious personal injury—including amputation, electrocution, or death. The
owner of this machine/tool is solely responsible for its safe use. This
responsibility includes but is not limited to proper installation in a safe
environment, personnel training and usage authorization, proper
inspectionandmaintenance, manual availability and comprehension, application
of safety devices, sanding/grinding tool integrity, and the usage of personal
protective equipment .The manufacturer will not be held liable for injury or
property damage from negligence, improper training, machine modifications or
misuse.
WARNING!
Some dust created by power sanding, sawing, grinding, contains chemical
sknown to the State of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
- Lead from lead-based paints.
- Crystalline silica from bricks, cement and other masonry products.
- Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do thi stype of work. To reduce your exposure to these chemicals: Work in a well ventilate darea, and work with approved safety equipment, such as those dust mask sthat ares pecially designed to filter out microscopic particles
| items| Description
---|---|---
1| Name| Gem Faceting Machine
2| Model| KD-8801
3| Paramete r|
Voltage/Frequency：110-120VAC/60Hz，Power：180W，Variablespeed：0-2980rpm
4| Package Size| 480x380x330mm
5| G.W.| 14.5KG
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>