BEISIT F500 UHF RFID Reader User Manual
- June 9, 2024
- BEISIT
Table of Contents
F500 UHF RFID Reader
User Manual
Product model:
F500
Product Picture
Technical characteristics
Transponder
Protocol| EPCglobal UHF Class 1 Gen 2/ISO 18000- 6C, ISO 18000-6B (Options)|
Working Current| <500mA@24V
---|---|---|---
Standby Current| <20mA@24V
Working Frequency| 860-960MHz| Communication| RS-232, RS-485
Working Region| FCC 902-928 MHz MI 865.6-867.6 MHz CN 920-925MHz Other Area
can be set up| Interface| 4PIN Green(+RS-485) ,DB-9, 5 SMA RF Connector
RF POWER| 5-30dBm(1dB Step adjustable)| Operating Temperature| -25°C to 65°C
Receiving Sensitivity| <-78dBm| Storage Temperature| -40°C to 85°C
RF Accuracy| ±1 dB| Relative Humidity| 10% – 95%
Flatness Of RF Power| ±0.2dB| Coling Type| Air Cooling
Reading Distance| >3.5m (According to different tag)| Dimensions(W x H x D)|
102.067.017.5mm
Reading Speed| >400 PCS/second| Weight| <115g
LED Indicator| Support| Housing Material| Aluminum alloy
RSSI| Support| Approval| FCC, CE, RoHS
Ambient Temperature
Monitoring| Support| Software Development
Materials| SDK & API
Working Voltage| DC 9-24V| |
Antenna interface
| ANTI : | SMA | DC9-24 V. | DC Power, voltage range9-24V |
|---|---|---|---|
| ANT2: | SMA | GND: | Signal&Power reference GND |
| ANT3: | SMA | 485 A: | Corn RS-485A Signal |
| ANT4: | SMA | 485 B: | Corn RS-485B Signal |
| ANTS: | SMA | RS232 | Standard D9 serial port |
LED Indicator Description
Tricolour light：
Red Lamp — Power，Blue Lamp — On-Reading，Green Lamp — Flash Got Tag。
Announcements：
Do not open the software when the antenna is not connected, otherwise no load
may damage the reader!
Dimensions
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
TEL:+86-571-8936 2888
Email: [email protected]
http://www.beisit.com