XRAY X1 2023 1 10 Formula Kit Excl Body Shell

Product Information

Specifications

• Model : XRAY
• Manufacturer : Team XRAY
• Contains : Lead (CAS 7439-92-1), Antimony (CAS 7440-36-0)
• Chemical Warning: This product contains a chemical known to the state of California to cause cancer and birth defects or other reproductive harm.
• Safety Precautions: Always wear protective glasses and gloves when building, using, and/or operating this model.

Product Usage Instructions

Before You Start

• Before you begin assembly, it is important to read and fully understand the instructions provided. Review the entire manual, download and use the set-up book from the web, and examine all details carefully. If you realize that this product is not what you wanted or expected, do not continue any further. Partially or fully assembled kits cannot be returned or exchanged by your hobby dealer.
• Prior to building and operating your XRAY, it is essential to read through all of the operating instructions and the instruction manual. Make sure you fully understand them in order to maximize your enjoyment and prevent unnecessary damage.
• Please note that the contents of the box may differ from the pictures. The specifications of the kit may also vary without prior notice due to continuous product development.

Customer Support

• We have made every effort to make these instructions as easy to understand as possible. However, if you encounter any difficulties, problems, or questions, do not hesitate to contact the XRAY support team at info@teamxray.com. You can also visit the official website at www.teamxray.com to find the latest updates, set-up information, option parts, and other resources. XRAY takes pride in providing excellent customer care.
• Join thousands of XRAY fans and enthusiasts in the online community at www.teamxray.com.

Contact XRAY USA RC America for any inquiries

• Address : 2030 Century Center Blvd #15 Irving, TX 75062 USA
• Phone : 214-744-2400
• Fax : 214-744-2401
• E-mail : xray@rcamerica.com

Failure to follow these instructions will be considered as abuse and/or neglect.

Safety Precautions
The product contains lead (CAS 7439-92-1) and antimony (CAS 7440-36-0). It is important to be aware of the potential hazards associated with these chemicals. This product contains a chemical known to the state of California to cause cancer and birth defects or other reproductive harm. Take the following precautions

• Wash thoroughly after using.
• Do not use the product while eating, drinking, or using tobacco products.
• May cause chronic effects to gastrointestinal tract, CNS, kidneys, and blood.
• May cause birth defects.

When building, using, and/or operating this model, always wear protective glasses and gloves. Take appropriate safety precautions before operating this model. You are responsible for the assembly and safe operation of this model. Please read the instruction manual before building and operating this model, and follow all safety precautions. Keep the instruction manual at hand for quick reference, even after completing the assembly. Use only genuine and original authentic XRAY parts for maximum performance. Using any third-party parts on this model will void the guarantee immediately.

R/C & Building Tips
Additional R/C and building tips may be provided in the instruction manual. Please refer to the manual for further guidance.

FAQ (Frequently Asked Questions)

• Q: How can I contact XRAY support for assistance?
  A: You can contact the XRAY support team at info@teamxray.com or visit www.teamxray.com for support and resources.

• Q: Can I return or exchange a partially or fully assembled kit?
  A: No, your hobby dealer cannot accept the kit for return or exchange once it has been partially or fully assembled.

• Q: Where can I find the latest updates, set-up information, and option parts?
  A: Visit the official website at www.teamxray.com for the latest updates, set-up information, and option parts.

• Q: What precautions should I take when operating this model?
  A: Always wear protective glasses and gloves. Operate the model in safe environments, away from children and people, residential areas, limited indoor spaces, wet conditions, streets, areas where loud noises can disturb others (such as hospitals and residential areas), and when visibility is obstructed or impaired.

• Q: Can I use third-party parts on this model?
  A: No, using any third-party parts on this model will void the guarantee immediately. Use only genuine and original authentic XRAY parts for maximum performance.

BEFORE YOU START

• This is a high-competition, high-quality RC car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision racing model. This model racing car is not intended for use by beginners, inexperienced customers, or by children without direct supervision of a responsible, knowledgeable adult. If you do not fulfill these requirements, please return the kit in unused and unassembled form back to the shop where you have purchased it.
• Before building and operating your XRAY, YOU MUST read through all of the operating instructions and instruction manual and fully understand them to get the maximum enjoyment and prevent unnecessary damage.

CUSTOMER SUPPORT

• We have made every effort to make these instructions as easy to understand as possible. However, if you have any difficulties, problems, or questions, please do not hesitate to contact the XRAY support team at info@teamxray.com. Also, please visit our Web site at www.teamxray.com to find the latest updates, set-up information, option parts, and many other goodies. We pride ourselves on taking excellent care of our customers.
• You can join thousands of XRAY fans and enthusiasts in our online community at: www.teamxray.com
• Read carefully and fully understand the instructions before beginning assembly.
• Make sure you review this entire manual, download and use set-up book from the web, and examine all details carefully. If for some reason you decide this is not what you wanted or expected, do not continue any further. Your hobby dealer can not accept your kit for return or exchange after it has been partially or fully assembled.
• Contents of the box may differ from pictures. In line with our policy of continuous product development, the exact specifications of the kit may vary without prior notice.

XRAY Europe

• K Vystavisku 6992
• 91101 Trenčín
• Slovakia, EUROPE
• Phone: 421-32-7401100
• Fax : 421-32-7401109
• E-mail : info@teamxray.com

XRAY USA
RC America, 2030 Century Center Blvd #15 Irving, TX 75062

USA

• Phone : 214-744-2400
• Fax : 214-744-2401
• E-mail : xray@rcamerica.com

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT.

SAFETY PRECAUTIONS

Contains
LEAD (CAS 7439-92-1) ANTIMONY (CAS 7440-36-0)

• WARNING : This product contains a chemical known to the state of California to cause cancer and birth defects or other reproductive harm.
• CAUTION : CANCER HAZARD
• Contains lead, a listed carcinogen. Lead is harmful if ingested. Wash thoroughly after using. DO NOT use product while eating, drinking or using tobacco products. May cause chronic effects to gastrointestinal tract, CNS, kidneys, and blood. MAY CAUSE BIRTH DEFECTS.
• When building, using and/or operating this model always wear protective glasses and gloves.
• Take appropriate safety precautions prior to operating this model. You are responsible for this model‘s assembly and safe operation! Please read the instruction manual before building and operating this model and follow all safety precautions. Always keep the instruction manual at hand for quick reference, even after completing the assembly. Use only genuine and original authentic XRAY parts for maximum performance. Using any third party parts on this model will void guaranty immediately.
• Improper operation may cause personal and/or property damage. XRAY and its distributors have no control over damage resulting from shipping, improper construction, or improper usage. XRAY assumes and accepts no responsibility for personal and/or property damages resulting from the use of improper building materials, equipment and operations. By purchasing any item produced by XRAY, the buyer expressly warrants that he/she is in compliance with all applicable federal, state and local laws and regulation regarding the purchase, ownership and use of the item. The buyer expressly agrees to indemnify and hold harmless XRAY for all claims resulting directly or indirectly from the purchase, ownership or use of the product. By the act of assembling or operating this product, the user accepts all resulting liability. If the buyer is not prepared to accept this liability, then he/she should return this kit in new, unassembled, and unused condition to the place of purchase.

IMPORTANT NOTES – GENERAL

• This product is not suitable for children under 16 years of age without the direct supervision of a responsible and knowledgeable adult.
• Carefully read all manufacturers warnings and cautions for any parts used in the construction and use of your model.
• Assemble this kit only in places away from the reach of very small children.
• First-time builders and users should seek advice from people who have building experience in order to assemble the model correctly and to allow the model to reach its performance potential.
• Exercise care when using tools and sharp instruments.
• Take care when building, as some parts may have sharp edges.
• Keep small parts out of reach of small children. Children must not be allowed to put any parts in their mouth, or pull vinyl bag over their head.
• Read and follow instructions supplied with paints and/or cement, if used (not included in kit).
• Immediately after using your model, do NOT touch equipment on the model such as the motor and speed controller, because they generate high temperatures. You may seriously burn yourself seriously touching them.
• Follow the operating instructions for the radio equipment at all times.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury as your finger, hair, clothes, etc. may get caught.
• Be sure that your operating frequency is clear before turning on or running your model, and never share the same frequency with somebody else at the same time. Ensure that others are aware of the operating frequency you are using and when you are using it.
• Use a transmitter designed for ground use with RC cars. Make sure that no one else is using the same frequency as yours in your operating area. Using the same frequency at the same time, whether it is driving, flying or sailing, can cause loss of control of the RC model, resulting in a serious accident.
• Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio equipment.
• Disconnect the battery pack before storing your model.
• When learning to operate your model, go to an area that has no obstacles that can damage your model if your model suffers a collision.
• Remove any sand, mud, dirt, grass or water before putting your model away.
• If the model behaves strangely, immediately stop the model, check and clear the problem.
• To prevent any serious personal injury and/or damage to property, be responsible when operating all remote controlled models.
• The model car is not intended for use on public places and roads or areas where its operation can conflict with or disrupt pedestrian or vehicular traffic.
• Because the model car is controlled by radio, it is subject to radio interference from many sources that are beyond your control. Since radio interference can cause momentary loss of control, always allow a safety margin in all directions around the model in order to prevent collisions.
• Do not use your model
  • Near real cars, animals, or people that are unaware that an RC car is being driven.
  • In places where children and people gather
  • In residential districts and parks
  • In limited indoor spaces
  • In wet conditions
  • In the street
  • In areas where loud noises can disturb others, such as hospitals and residential areas.
  • At night or anytime your line of sight to the model may be obstructed or impaired in any way.

To prevent any serious personal injury and/or damage to property, please be responsible when operating all remote controlled models.

IMPORTANT NOTES – ELECTRICAL

• Insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check connectors for if they become loose. And if so, reconnect them securely. Never use RC models with damaged wires. A damaged wire is extremely dangerous, and can cause short-circuits resulting in fire. Please have wires repaired at your local hobby shop.
• Low battery power will result in loss of control. Loss of control can occur due to a weak battery in either the transmitter or the receiver. Weak running battery may also result in an out of control car if your car‘s receiver power is supplied by the running battery. Stop operation immediately if the car starts to slow down.
• When not using RC model, always disconnect and remove battery.
• Do not disassemble battery or cut battery cables. If the running battery short-circuits, approximately 300W of electricity can be discharged, leading to fire or burns. Never disassemble battery or cut battery cables.
• Use a recommended charger for the receiver and transmitter batteries and follow the instructions correctly. Over-charging, incorrect charging, or using inferior chargers can cause the batteries to become dangerously hot. Recharge battery when necessary. Continual recharging may damage battery and, in the worst case, could build up heat leading to fire. If battery becomes extremely hot during recharging, please ask your local hobby shop for check and/or repair and/or replacement.
• Regularly check the charger for potential hazards such as damage to the cable, plug, casing or other defects. Ensure that any damage is rectified before using the charger again. Modifying the charger may cause short-circuit or overcharging leading to a serious accident. Therefore do not modify the charger.
• Always unplug charger when recharging is finished.
• Do not recharge battery while battery is still warm. After use, battery retains heat. Wait until it cools down before charging.
• Do not allow any metal part to short circuit the receiver batteries or other electrical/electronic device on the model.
• Immediately stop running if your RC model gets wet as may cause short circuit.
• Please dispose of batteries responsibly. Never put batteries into fire.

R/C & BUILDING TIPS

• Make sure all fasteners are properly tightened. Check them periodically.
• Make sure that chassis screws do not protrude from the chassis.
• For the best performance, it is very important that great care is taken to ensure the free movement of all parts.
• Clean all ball-bearings so they move very easily and freely.
• Tap or pre-thread the plastic parts when threading screws.
• Self-tapping screws cut threads into the parts when being tightened. Do not use excessive force when tightening the self-tapping screws because you may strip out the thread in the plastic. We recommended you stop tightening a screw when you feel some resistance.
• Ask your local hobby shop for any advice.

WARRANTY

• XRAY guarantees this model kit to be free from defects in both material and workmanship within 30 days of purchase. The total monetary value under warranty will in no case exceed the cost of the original kit purchased. This warranty does not cover any components damaged by use or modification or as a result of wear. Part or parts missing from this kit must be reported within 30 days of purchase.
• No part or parts will be sent under warranty without proof of purchase. Should you find a defective or missing part, contact the local distributor. Service and customer support will be provided through local hobby store where you have purchased the kit, therefore make sure to purchase any XRAY products at your local hobby store. This model racing car is considered to be a high-performance racing vehicle. As such this vehicle will be used in an extreme range of conditions and situations, all which may cause premature wear or failure of any component. XRAY has no control over usage of vehicles once they leave the dealer, therefore XRAY can only offer warranty against all manufacturer‘s defects in materials, workmanship, and assembly at point of sale and before use. No warranties are expressed or implied that cover damage caused by what is considered normal use, or cover or imply how long any model cars‘ components or electronic components will last before requiring replacement.
• Due to the high performance level of this model car you will need to periodically maintain and replace consumable components. Any and all warranty coverage will not cover replacement of any part or component damaged by neglect, abuse, or improper or unreasonable use. This includes

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials, the best compounds for molded parts and the most sophisticated manufacturing processes of TQM (Total Quality Management). We guarantee that all parts of a newly- purchased kit are manufactured with the highest regard to quality. However, due to the many factors inherent in model racecar competition, we but is not limited to damage from crashing, chemical and/or water damage, excessive moisture, improper or no maintenance, or user modifications which compromise the integrity of components. Warranty will not cover components that are considered consumable on RC vehicles. XRAY does not pay nor refund shipping on any component sent to XRAY or its distributors for warranty. XRAY reserves the right to make the final determination of the warranty status of any component or part.

Limitations of Liability

• XRAY makes no other warranties expressed or implied. XRAY shall not be liable for any loss, injury or damages, whether direct, indirect, special, incidental, or consequential, arising from the use, misuse, or abuse of this product and/or any product or accessory required to operate this product. In no case shall XRAY‘s liability excess the monetary value of this product.
• Take adequate safety precautions prior to operating this model. You are responsible for this model’s assembly and safe operation.
• Disregard of the any of the above cautions may lead to accidents, personal injury, or property damage. XRAY MODEL RACING CARS assumes no responsibility for any injury, damage, or misuse of this product during assembly or operation, nor any addictions that may arise from the use of this product.
• All rights reserved.
• cannot guarantee any parts once you start racing the car. Products which have been worn out, abused, neglected or improperly operated will not be covered under warranty.
• We wish you enjoyment of this high-quality and high-performance RC car and wish you best success on the track!
• In line with our policy of continuous product development, the exact specifications of the kit may vary. In the unlikely event of any problems with your new kit, you should contact the model shop where you purchased it, quoting the part number.
• We do reserve all rights to change any specification without prior notice. All rights reserved.

TOOLS REQUIRED

INCLUDED

ALSO REQUIRED

NOT INCLUDED

COLOR INDICATIONS
At the beginning of each section is an exploded view of the parts to be assembled. There is also a list of all the parts and part numbers that are related to the assembly of that section.
The part descriptions are color-coded to make it easier for you to identify the source of a part. Here are what the different colors mean:

• 372127 STYLE A – indicates parts that are included in the bag marked for the section.
• 371028 STYLE B – indicates parts that are included in the box.
• 374901 STYLE C – indicates parts that are already assembled from previous steps.

GRAPHITE PARTS PROTECTION

To protect and seal edges of graphite parts, sand edges smooth and then apply CA glue. Make it: this for chassis edges and countersunk holes.

FRONT SUSPENSION

• 302132-M CFF™ CARBON-FIBER FUSION UPPER ARM – MEDIUM – FR/RL
• 302142-M CFF™ CARBON-FIBER FUSION UPPER ARM – MEDIUM – FL/RR
• 302311 ALU CASTER BUSHING FRONT 4° / REAR 1.5°/4.5° – 2 DOTS (4)
• 302640 ADJUSTABLE CAMBER SCREW 14mm M4 L/R – HUDY SPRING STEEL™ (2)
• 302666 COMPOSITE BALL JOINT 4.9mm F+R – OPEN (2+2)
• 303122-K ALU SHIM 3x6x1.0mm (10)
• 303141 ALU SHIM 3x5x1.0mm (10)
• 303232 UPPER ARM BALL UNIVERSAL 4.9mm – HUDY SPRING STEEL™ (2)
• 362648 BALL END 4.9mm WITH THREAD 4mm (2)
• 371059 GRAPHITE ARM MOUNT PLATE – NARROW TRACK-WIDTH – 2.5mm
• 371069 GRAPHITE ARM MOUNT PLATE – WIDE TRACK-WIDTH – 2.5mm
• 372092 GRAPHITE FRONT ARM BRACE 2.2mm
• 372127 GRAPHITE LOWER SUSPENSION ARM 2.5mm
• 372177 FRONT COIL SPRING 3.6x6x0.5mm; C=3.5 – GOLD (2)
• 372213 COMPOSITE STEERING BLOCK & BACKSTOPS
• 372286 KING PIN (2)
• 372290 ALU SHIM 3.2×4.8×0.5 (4)
• 372320 COMPOSITE ARM BUSHING (4)
• 373242 COMPOSITE PIVOTBALL UNIVERSAL 6.0mm – SHORT (2)
• 373245 X1 UPPER ARM BALL UNIVERSAL 4.9mm – HUDY SPRING
• STEEL™ (2)
• 375221 FRONT WHEEL AXLE – HUDY SPRING STEEL™ (2)
• 376264 ALU FRONT TOP DECK MOUNT – SWISS 7075 T6
• 376364-K ALU MOUNT 10.8mm – BLACK (2)
• 901304 HEX SCREW SB M3x4 (10)
• 901308 HEX SCREW SB M3x8 (10)
• 902306 HEX SCREW SH M3x6 (10)
• 902308 HEX SCREW SH M3x8 (10)
• 903306 HEX SCREW SFH M3x6 (10)
• 903308 HEX SCREW SFH M3x8 (10)
• 965019 E-CLIP 1.9 (10)
• 970050 O-RING 5×1 (10)
• 371028 X1’23 GRAPHITE CHASSIS 2.5mm

ALTERNATIVE 1

STANDARD TRACK-WIDTH (INITIAL SETTING)
Standard track-width setting is used for standard F1 front tires such HUDY, RIDE, HOT RACE.
To make sure that you use the correct setting, measure the track-width with the tires; the track-width must be maximum 190mm.

ALTERNATIVE 2

WIDE TRACK-WIDTH

• Wide track-width setting is used for the narrow F1 front tires such as Volante.
• To make sure that you use the correct setting, measure the track-width with the tires; the track-width must be maximum 190mm.

YOU CAN INSTALL A LOWER ARM BRACE TO INCREASE STEERING RESPONSE.

1. SOFT – WITHOUT THE BRACE (INITIAL SETTING)
   The car will have less initial steering. Recommended for high- and very-high- traction carpet tracks where the car needs to be easy to drive and less responsive.

2. MEDIUM – WITH BRACE
   Improves in-corner steering but still keeps the car easy to drive. Recommended for medium-high traction carpet tracks and high-traction asphalt tracks.

3. STIFF – WITH BRACE AND CONNECTED TO ALU FRONT STAND
   Provides maximum steering response. Recommended for low-medium traction carpet tracks and for all different traction conditions on asphalt tracks.

SOFTER SPRINGS
Makes the car easier to drive over bumps and increases steering as it makes the car roll more, especially in the middle of a corner.

HARDER SPRINGS
Makes the car more responsive and increases initial steering. Recommended for high-traction and flat tracks.

2x
After assembling the steering block, do the following:

1. Loosen the set-screw slightly.
2. Use your thumb to press down on the top of the kingpin, while using your other fingers to pull up the steering block.
3. Tighten the set-screw.

JAN RATHEISKY (factory driver)
We use different ride heights at indoor and outdoor tracks:

• INDOOR : Ride height is as low as the rules allow, usually 4mm.
• OUTDOOR : Always run at least 5mm ride height.

Rear ride height should always be 0.1-0.2mm higher than the front.
I recommend changing droop using the upper shims on the kingpin, but note that this also changes the ride height by the same amount. Adding +0.5mm shim means 0.5mm less droop because the spring gets more preload which results in a higher ride height. In that case, you should add the same amount (0.5mm) under the lower wishbone.

DROOP SETTING INDOOR
I recommend using a small amount of droop for carpet tracks, somewhere between 0.5-1mm to get the most on-power steering in combination with solid reactive steering

OUTDOOR
You should use more droop for asphalt tracks. At least 1mm up to 2mm. The more droop, the more on-power rear traction you get because of weight transfer to the rear. It also helps to get a more smooth-to-drive car at corner entry.

REAR SUSPENSION

• 303122-K ALU SHIM 3x6x1.0mm – BLACK (10)
• 303123-K ALU SHIM 3x6x2.0mm – BLACK (10)
• 303130-K ALU SHIM 3x6x9.0mm – BLACK (10)
• 303241 PIVOT BALL UNIVERSAL 5.8mm WITH HEX (4)
• 371082 GRAPHITE REAR BRACE 3.5mm
• 371096 GRAPHITE PLATE FOR MOUNTS 2.5mm
• 371184-K ALU POD LINK GRAPHITE PLATE HOLDER – BLACK
• 371185 GRAPHITE POD LINK PLATE 2.5mm (2)
• 371190 COMPOSITE POD LINK (2)
• 371320 COMPOSITE BODY POST (2)
• 372650 BALL END 4.2mm WITH 6mm THREAD (2)
• 372662 COMPOSITE BALL-JOINT 4.2mm (4)
• 373018 ALU REAR BULKHEAD – MOTOR (RIGHT)
• 373028 ALU REAR BULKHEAD – LEFT
• 373050 GRAPHITE REAR BULKHEAD BRACE 2.0mm
• 373073-K ALU REAR BRACE MOUNT 13mm – BLACK (2)
• 373075 ALU REAR BRACE MOUNT 10.5mm – BLACK (2)
• 373095 ALU CHASSIS PIVOT HOLDER – SWISS 7075 T6
• 373096 ALU POD PLATE PIVOT HOLDER – SWISS 7075 T6
• 373097 COMPOSITE PIVOT BRACE BUSHING
• 373554 GRAPHITE REAR POD UPPER PLATE 2.5mm
• 373585 SIDE SPRING C=0.9 – GOLD (2)
• 373591 COMPOSITE SIDE SPRING HOLDER (2)
• 376150 GRAPHITE ADJUSTABLE BATTERY HOLDER 1.6mm (2)
• 376170 GRAPHITE BATTERY CLAMP 2.2mm (2)
• 376290 LOW PROFILE ALU SELF-LOCKING NUT (2)
• 376328 SIDE BRACE – GRAPHITE 2.5mm – RIGHT & LEFT
• 376361-K ALU MOUNT 26.5mm – BLACK (2)
• 378141 SIDE LINKAGE TUBE (2)
• 378153 COMPOSITE LINKAGE SHAFT (2)
• 901308 HEX SCREW SB M3x8 (10)
• 902256 HEX SCREW SH M2.5×6 (10)
• 902258 HEX SCREW SH M2.5×8 (10)
• 902305 HEX SCREW SH M3x5 (10)
• 902306 HEX SCREW SH M3x6 (10)
• 902308 HEX SCREW SH M3x8 (10)
• 902318 HEX SCREW SH M3x18 (10)
• 903305 HEX SCREW SFH M3x5 (10)
• 903306 HEX SCREW SFH M3x6 (10)
• 903308 HEX SCREW SFH M3x8 (10)
• 960030 NUT M3 (10)
• 981210 PIN 2×10 (10)
• 371163 GRAPHITE REAR POD LOWER PLATE 2.5mm

PIVOT MOUNTING ALTERNATIVE

• REARWARD: (INITIAL SETTING)
  Pivot mounted in rearward chassis holes, and 1mm shim used under the pivot ball. The rearward pivot mounting position gives the most steering and most free rear end. Recommended for high-traction conditions such as US black carpet.

• FORWARD
  Pivot mounted in forward chassis holes, with 3mm shims under the pivot ball. The forward pivot mounting position gives a good balance between front and rear traction.

OPTIONAL SIDE SHOCK
# 378100
Optional side shock can be used to improve traction in low- and medium- traction conditions. The optional side shock REPLACES the 2 side tubes.

CHASSIS FLEX ADJUSTMENT

• SOFT (NO BRACES)
  Generates more mechanical grip. Recommended for low- to medium-traction carpet as well as asphalt.

• MEDIUM
  Braces installed, attached at middle & rear only. This setting is a good compromise between mechanical grip and steering response. Ideal for most conditions.

• STIFF
  Braces installed, attached at front, middle, and rear. This is the stiffest, most stable setting. Recommended for high-traction carpet (such as US black carpet). The car will have less roll but will also have less overall grip.

3. BALL DIFFERENTIAL

• 372070 COMPOSITE RIDE HEIGHT ADJUSTER SET – V2 (2)
• 375012 STEEL REAR AXLE SHAFT – HUDY SPRING STEEL™
• 375026 ALU REAR DRIVE AXLE – RIGHT
• 375036 ALU REAR WHEEL HUB – RIGHT
• 375046 ALU REAR WHEEL HUB – LEFT
• 375050 ALU DIFF HUB
• 375080 D-LOCK DIFF PLATE (2)
• 375090 SET OF ALU SHIMS 6.37×8.4mm (0.5mm, 1.0mm, 2.0mm)
• 375896 COMPOSITE SPUR GEAR – 96T / 64P
• 901304 HEX SCREW SB M3x4 (10)
• 908258 HEX SCREW SOCKET HEAD CAP M2.5×8 (10)
• 930130 CARBIDE BALL 3.175mm (12)
• 930138 CARBIDE BALL-BEARING AXIAL F3-8 3x8x3.5 – V2
• 941438 BALL-BEARING 1/4”x3/8”x1/8” RUBBER SEALED – OIL (2)
• 951438 BALL-BEARING 1/4” x 3/8” x 1/8” FLANGED – STEEL SEALED – OIL (2)
• 960030 NUT M3 (10)
• 963030 CONE WASHER ST 3x8x0.5 (10)
• 981214 PIN 2×14 (10)

CENTER SHOCK

• 303241 BALL UNIVERSAL 5.8mm HEX (4)
• 308037 COMPOSITE PISTONS 4-HOLE 1.0-1.2mm, 3-HOLE 1.0-1.2mm
• 308042-K ALU SHOCK ADJUSTABLE NUT – BLACK (2)
• 308082 SHOCK ABSORBER MEMBRANE (4)
• 308316 SHOCK BALL JOINT – OPEN (4)
• 308323 ALU XRAY SHOCK BODY (2)
• 308327-K ALU CAP FOR XRAY SHOCK BODY – BLACK
• 308333 COMPOSITE SHOCK PARTS FOR ALU SHOCKS
• 308353-K ALU SHOCK CAP-NUT WITH VENT HOLE – BLACK (2)
• 308263 XRAY 4S SPRING-SET PROGRESSIVE C=2.3-2.6 (2)
• 378062 SHOCK SHAFT
• 378072-K ALU SHOCK SPRING COLLAR – BLACK
• 901303 HEX SCREW SB M3x3 (10)
• 965023 E-CLIP 2.3 (10)
• 970130 O-RING 13 x 1.5 (10)
• 972030 SILICONE O-RING 3 x 2 (10)

SHOCK FILLING

• SOFTER OIL
  Recommended for bumpy and low-traction tracks, generates more traction.

• HARDER OIL
  Recommend for flat and high-traction tracks, improves steering response.

1. Fully extend the piston rod so the piston is at the bottom of the shock body.
2. Hold the shock upright and slightly overfill the shock body with shock oil.
3. Let the oil settle and allow air bubbles to rise to the top. Slowly move the piston up and down to allow oil into all cavities within the shock body.
4. Extend the piston rod most of the way out of the shock body. Let the shock rest for 5 minutes to allow the air bubbles to escape.
5. Add shock oil as necessary.

1. When installing the shock cap assembly on the shock body, some oil will leak out… this is normal.
2. Tighten the cap and clean off any excess oil.
3. After the shock is assembled, the shock rod will push itself out of the shock body fairly quickly.
4. Follow the next procedure to adjust the rebound.

REBOUND ADJUSTMENT AFTER THE SHOCK IS ASSEMBLED YOU HAVE TO SET THE SHOCK REBOUND:

1. Release the shock cap by 2-3 turns.
2. Push the shock shaft fully up. For the first time the extra oil will release through the hole in the alu cap-nut.
3. Tighten the shock cup. When tightening the shock cap, extra oil will again release through the hole in the alu cap – nut. When tightening, the shock shaft will push out from the shock body.

REBOUND CHECK REBOUND CHECK
It is very important to push the shock shaft into the shock body slowly otherwise air can come into the shock body which would create bubles.

• 100% rebound – do not do step 2 and 3
• 75% rebound – repeat steps 1 to 3 until the shock shaft will push out 75% of its length
• 50% rebound – repeat steps 1 to 3 until the shock shaft will push out 50% of its length
• 25% rebound – repeat steps 1 to 3 until the shock shaft will push out 25% of its length
• 0% rebound – repeat steps 1 to 3 until the shock shaft will push out 0% of its length

If the shock shaft does not rebound enough, you will have to refill the shock with shock oil, and then repeat the bleeding and rebound adjustment procedure

Jan Ratheisky (Factory Driver)
Set the ride height for your track and measure it at the link connection of the side pod. Lift the car on the rear part of the center shock. When you unload the shock fully, you can measure the height at the same spot again. The difference to the ride height is the droop amount. The set-up of the rear downstop is very important to find a good balance between traction and rotation. On both indoor and outdoor tracks, I recommend starting with 1mm droop. Less droop gives you more rear traction. Recommended for low-traction conditions. More droop frees up the rear and makes it looser, but results in more steering. You should not use more than 2.5mm rear droop at maximum.

DOWNSTOP ADJUSTMENT
The length of the shock absorber affects the amount of rear downstop. To adjust, thread the ball-joint on or off the bottom spring cap.

FINAL ASSEMBLY

• 305968~294160 PINION GEAR HARDCOATED 18~60T/64P

• 372541-K ALU ADJUSTABLE SERVO SAVER SET – BLACK

• 371202 X1 COMPOSITE ADJUSTABLE FRONT AERO WING – ETS APPROVED

• 371203-K X1 COMPOSITE ADJUSTABLE FRONT WING – BLACK – ETS APPROVED

• 371203 X1 COMPOSITE ADJUSTABLE FRONT WING – WHITE – ETS APPROVED

• 371204-K X1 COMPOSITE ADJUSTABLE FRONT WING – BLACK – FLAT DESIGN

• 371204 X1 COMPOSITE ADJUSTABLE FRONT WING – WHITE – FLAT DESIGN

• 373512-K X1 COMPOSITE ADJUSTABLE REAR WING – BLACK

• 373513-K X1 COMPOSITE ADJUSTABLE REAR WING – BLACK – ETS APPROVED

• 373514 X1 COMPOSITE REAR WING – LIGHTWEIGHT & WIDE – WHITE

• 379701 XRAY X1 1/10 FORMULA BODY

• 379702 XRAY X1 1/10 FORMULA BODY – WORLD CHAMPION EDITION

• 803072 HUDY 1/10 FORMULA RUBBER TIRE – FRONT (2)

• 803082 HUDY 1/10 FORMULA RUBBER TIRE – REAR (2)

• 301370 ALU PLATE FOR REAR GRAPHITE BODY POST HOLDER
• 302612 ALU ADJ. TURNBUCKLE M3 L/R 39mm – SWISS 7075 T6 (2)
• 302663 COMPOSITE BALL JOINT 4.9mm – OPEN – V2 (8)
• 302665 COMPOSITE BALL JOINT 4.9mm – CLOSED WITH HOLE (4)
• 303125-K ALU SHIM 3x6x3.0mm (10)
• 303130-K ALU SHIM 3x6x9.0mm (10)
• 306200-K ALU SERVO MOUNT – BLACK (2)
• 306219 COMPOSITE SET OF SERVO SHIMS (4)
• 306301 ANTENNA MOUNT – THIN
• 309400 BODY CLIP (8)
• 362650 BALL END 4.9mm WITH THREAD 6mm (2)
• 362651 BALL END 4.9mm WITH THREAD 8mm (2)
• 371290-K ALU BODY POST PLATE – BLACK
• 371320 COMPOSITE BODY POST (2)
• 372503 COMPOSITE SERVO SAVER – X-STIFF – SET – V2
• 372540 COMPOSITE STEERING ARM
• 373051 GRAPHITE REAR WING MOUNT 2.5mm
• 373526 GRAPHITE REAR WING HOLDER PLATE 2.5mm (L+R)
• 376132 GRAPHITE BATTERY BACKSTOP 3.0mm – MIDDLE
• 376235 GRAPHITE TOP DECK 2.2mm
• 376364-K ALU MOUNT 10.8mm – BLACK (2)
• 338586 SHIM 5x7x0.5 (10)
• 902205 HEX SCREW SH M2x5 (10)
• 902306 HEX SCREW SH M3x6 (10)
• 902308 HEX SCREW SH M3x8 (10)
• 902314 HEX SCREW SH M3x14 (10)
• 903306 HEX SCREW SFH M3x6 (10)
• 903308 HEX SCREW SFH M3x8 (10)
• 903310 HEX SCREW SFH M3x10 (10)
• 903416 HEX SCREW SFH M4x16 (10)
• 940508 BALL-BEARING 5x8x2.5 RUBBER SEALED – OIL (2)
• 940510 BALL-BEARING 5x10x4 RUBBER SEALED – OIL (2)
• 960030 NUT M3 (10)
• 960040 NUT M4 (10)
• 981210 PIN 2×10 (10)
• 306310 ANTENNA (2)
• 371250 X1 LEXAN FRONT SPOILER (2)
• 373514-K X1 COMPOSITE REAR WING – LIGHTWEIGHT & WIDE – BLACK
• 371201 X1 COMPOSITE FRONT BUMPER

BATTERY MOUNTING POSITIONS
The X1 has 4 battery mounting positions. The more forward the battery is, the car will be easier to drive but it will be less responsive. The more rearward the battery is, the car will be more aggressive and have more steering.

1. Before cutting and making holes on the body, put the unpainted body on the chassis to confirm the mounting position and location for holes and cutouts.
2. Before cutting and making holes on the front wing, put the unpainted wing on the front bumper to confirm the mounting position and location for holes and cutouts. Before painting, wash the inside of the body with mild detergent, and then rinse and dry thoroughly.
3. Mask the helmet shield if you wish.
4. Apply paint masks as appropriate.
5. Paint the body using paints formulated for polycarbonate bodies.
6. When the paint is dry, remove the masking.
7. Carefully cut out the body using appropriate scissors or cutting tools.
8. When you have finished cutting, peel off the external protective films.

KRAY EUROPE XRAY, K VYSTAVISKU 6992, 91101 TRENCIN, SLOVAKIA,

• EUROPE PHONE: +421-32-740 11 00,
• FAX : +421-32-740 11 09,
• info@teamxray.com

KRAY USA
RC AMERICA, 2030 Century Center Blvd #15, Irving, TX 75062,

• USA PHONE : 214-744-2400,
• FAX: 214-744-2401,
• xray@rcamerica.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>