HTU C126 Car Phone Mount User Manual
- June 15, 2024
- HTU
Table of Contents
HTU C126 Car Phone Mount
Specifications
- Design priorities: safety, convenience, elegance
- Telescopic arms with angle adjustment
- Silicone support stabilizer to prevent vibration and support long arm
- Upgraded suction cup that is reusable and doesn’t yellow or melt
- Suction cup suitable for clean, flat, smooth, and non-porous surfaces
Product Usage Instructions
**Installation
**
The HTU Car Phone Mount can be installed on either the dashboard or windshield of your vehicle. Follow the steps below for proper installation:
Dashboard Installation
- Clean the dashboard surface to ensure it is flat, smooth, and non-porous.
- Wait for the surface to dry.
- Attach the suction cup to the desired spot on the dashboard.
- Rotate the suction cup to the suitable view.
- Press down the suction cup lock fully to fix it in place.
Windshield Installation
If you have a leather or textile dashboard, it is recommended to install the
mount on the windshield instead. Follow the steps below for proper
installation:
- Clean the windshield surface to ensure it is flat, smooth, and non-porous.
- Wait for the surface to dry.
- Attach the suction cup to the desired spot on the windshield.
- Rotate the suction cup to the suitable view.
- Press down the suction cup lock fully to fix it in place.
Practical Tips
Here are some practical tips to ensure optimal usage of the HTU Car Phone
Mount:
- Do not install the suction cup on leather or textile dash surfaces.
- Clean the dashboard or windshield before installing the suction cup each time to maintain its viscosity and absorption force.
A Letter from an Engineer
Dear Customer，
As a product engineer, your detailed suggestions are highly appreciated. To
deserve your trust,I always keep upgrading my products since 2010.
What drives me to be a Car Mount Engineer?
A traffic accident made me realize that the car mount is important for driver
safety, cell phone safety, and vehicle safety, especially on the highway. I’ve
been reading feedback on Amazon’s car mounts to find inspiration to design a
better product for you.
Design priorities: safety first, convenience second, elegance third.
I always design products with driver safety in mind, but it is not easy to match them to hundreds of types of cars, and thanks to many users’ suggestions, this product was originally designed with 5 major improvements:
-
No.1: Without removing the suction cup, our new version can be rotated 360° at any angle when the “LOCK” button is unlocked.
(Normal Version: the suction cup can be only adjusted up and down, forward and backward once fixed, but cannot be rotated 360° .) -
No.2: Our upgraded telescopic arm can be extended to the distance you like without twisting the knob.
(Normal Version: telescopic arms are manually adjusted with a knob, which is inconvenient and dangerous while driving.) -
No.3: The silicone support stabilizer is designed to prevent vibration and support the long arm in case it falls off and also serves as a cable organizer to prevent the car cables from getting messy.
(Normal Version: The long telescopic arms vibrate or even fall off during driving.) -
No.4: Our upgraded suction cup can be reusable after washing and removed without yellow and melting.
-
No.5: For better durability (10,000 times) and thermal stability (-45°F~215°F), we adopt healthy refined materials that have been tested hundreds of times.
All the innovation means surprise or risk, but it will work in long term. I hope that this new car mount with silicone stabilizer will meet your expectation. If it doesn’t fit your vehicle or any problem, pls contact htuservice@163.com to get a solution until you have 100% Satisfaction!
Best Regards!
Product Diagram
**Package Contents
**
**Installation Spot
**
Dashboard or windshield.
Practical Tips
The suction cup is suitable for clean, flat, smooth, and non-porous surfaces.
WARNING:
- Leather or textile dash surfaces are not suitable for installing all suction cups, if you have these dashboards, please install the mount on the windshield.
- To ensure the viscosity and absorption force of the suction cup, please clean the dashboard or windshield first befue installing the suction cup every time
Tips for Using the Suction Cup
- Find a flat and smooth dashboard, clean the surface, and wait for it to dry.
- After attaching the suction cup, rotate it to the suitable view and then press down the suction cup lock totally to fix it.
- After attaching the suction cup, rotate it to the suitable view and then press down the suction cup lock totally to fix it.
- After attaching the suction cup, rotate it to the suitable view and then press down the suction cup lock totally to fix it.
- In the extreme summer heat: Please install the suction cup on the dashboard, not the windshield, and keep the suction cup away from direct sunlight.
- The temperature outside the car is over 1040F/40C which causes the temperature inside the car to be over 2030795 C. the adsorption forces would be lower. Please rinse the suction cup to restore the adsorption forces.
- You could change the direction of the telescopic arm without removing the suction cup. The suction cup can be rotated 3600 after turning on the “LOCK” button. And the direction of the telescopic arm will be fixed after pressing the “LOCK” button.
- After every time you turn on the suction cup “LOCK” and rotate the suction cup, please press and hold the suction cup for 5s, then press the “LOCK” button again.
Contact htuservice@163.com to get support if any problem during use.
Tips for Removing the Suction Cup
- Pull up the lock button.
- Pull the tab on the suction cup to allow air to get into it, stick a plastic putty knife and floss underneath to break the seal.
- Once the seal is broken you will be able to remove it easier.
Tips for Reusing the Suction Cup
- If the suction cup is loose, please wash the suction cup and wait for it dry, install it again.
- If the dashboard is not clean, and the suction cup is easy to shake and loosen, please wash the PU gel of the suction cup with water, clean up the dashboard, then reinstall the suction cup.
Temperature rising makes a horrible in-car environment. Please pay attention to the safety of pets and babies.
Car temps over time:
Email : htuservice@163.com
Website : http://htulink.com
Using the suction cup
- Unscrew the nut and remove it.
- Insert the ball joint into the back of the holder, and then screw the nut tightly.
- Find a flat and smooth surface, clean it with a wet and dry towel.
- Turn on the “LOCK” button of the sucker, then tear off the plastic sealing film on the bottom.
- Place the suction cup and rotate it to a suitable view.
- Press the base for 5s and make sure it fits the surface, and then press the lock button.
- Adjust the length and angle of the arm.
- Install the stabilizer, and press it firmly to ensure tight adhesion.
- Fix the telescopic arm in the notch of the stabilizer to make the bracket more stable. C)
- Tighten the knob to ensure stability. Leave it for 20mins to ensure the suction cup is stable before use.
- Place the Phone, Plug the cable in the cable organizer hole when not charging.
Rinsing the bottom of the suction cup and then air-drying to restore its adhesion and reuse.
Pull up the lock button and remove the suction cup.
Clamp the
Phone
- Press the release buttons on the back of the holder.
- Pull down the bottom tray.
- Put the phone, and then press the clamp arms.
How to Get Product
Installation Video?
Scan the QR Code
Frequent Q & A
How to avoid the mount falling off?
- Choose a flat and smooth surface.
- Clean the surface and wait for it to dry.
- Open the lock button.
- Tear off the plastic film on the suction cup.
- Place the suction cup and rotate it to a suitable view.
- Press the base for 5s and then press the lock button.
- Fix the telescopic arm in the notch of the stabilizer to make the bracket more stable. Wait for 20mins, and ensure stability before usage.
- It is recommended to install the windshield below these situations:
- The surface texture of the dashboard has too deep lines or the slope is too big.
- The dashboard is a leather surface, breathable surface, curved surface, plush cloth surface, uneven surface.
- High temperature, strong ultraviolet rays and dirty surface will affect the suction and stickiness, please avoid direct sunlight on the suction cup and clean it to restore vitality.
- When the vehicle is regularly maintained, please check the stability of the mount, which depends on:
- The local road conditions, temperature, and the severity of ultraviolet rays.
- The depth of the texture and slope of the surface.
We will try our best to deserve your trust. No need to return the items. Replacement, 24-hour response, and 5 years warranty until your 100% satisfaction if any problem:
Email : htuservice@163.com
Website : http://htulink.com
Can I reuse the suction cup?
Yes, the upgraded suction cup can be reused after washing and does not yellow or melt.
Can I adjust the angle of the mount?
Yes, the telescopic arm allows for angle adjustment according to your preference.
Is the silicone support stabilizer included?
Yes, the package includes a silicone support stabilizer that prevents vibration and supports the long arm. It also serves as a cable organizer.
How can I contact customer service?
You can contact customer service by emailing htuservice@163.com. They will provide you with a solution until you are 100% satisfied.
How to reuse the suction cup?
If the suction cup is loose, simply restore clean the sticky gel on your suction cup, rinsing the bottom of the suction cup then air-drying to restore its adhesion and reuse.